KitchenAid KEC56 User manual

Stand Mixer - Bowl Lift

KEC56

KEC66

1Motor Head

2Attachment Hub

3Attachment Knob

4Hub Cover

5Beater Shaft

6Speed Control Lever

7Bowl-Lift Lever

8Beater Height Adjustment Screw

9Bowl Support

10 Locating Pins

11 Bowl*

12 Bowl Handle*

13 Double Flex Edge Beater**

14 Flat Beater

15 Spiral Dough Hook

16 Wire Whip**

17 11-Wire Stainless Steel Elliptical

Whip**

18 Pouring Shield**

19 Spring Latch and Bowl Pin

(Not Shown)

20 Pastry Beater**

21 Flex Edge Beater**

22 Scraper** ***

*Bowl type may vary. Bowls are also available for purchase as separate accessories.

**Included with select models. Picture/Style may vary from product depending on model.

***Can also be used to scrape your Bowl.

0 .5 1 2 3 4 5 6 7 8 9 10

11 12

13 14 15 16 17

522

W11604421A.indb 1W11604421A.indb 1 6/16/2022 11:21:20 AM6/16/2022 11:21:20 AM

PRODUCT SAFETY

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always

be followed, including the following:

1. Read all instructions. Misuse of appliance may result in personal injury.

2. To protect against the risk of electrical shock do not put Stand Mixer in water or

other liquid.

3. This appliance is not intended for use by persons (including children) with

reduced physical, sensory, or mental capabilities, or lack of experience and

knowledge unless they are closely supervised and instructed concerning the

use of the appliance by a person responsible for their safety. Close supervision

is necessary when any appliance is used by or near children. Children should be

supervised to ensure that they do not play with the appliance.

4. Turn the appliance to off (0), then unplug from the outlet when not in use, before

assembling or disassembling parts and before cleaning. To unplug, grasp the

plug and pull from the outlet. Never pull from the power cord.

5. Avoid contacting moving parts. Keep hands, hair, clothing, as well as spatulas

and other utensils, away from beater during operation to reduce the risk of injury

to persons, or damage to the mixer.

6. Never leave the appliance unattended while it is in operation.

7. Do not operate any appliance with a damaged cord or plug, or after the

appliance malfunctions, or is dropped or damaged in any manner. Return

appliance to the nearest Authorised Service Facility for examination, repair, or

electrical or mechanical adjustment.

8. The use of accessories or attachments not recommended or sold by the

manufacturer may cause re, electric shock or injury.

9. Do not use the appliance outdoors.

10. Do not let the cord hang over the edge of table or counter.

W11604421A.indb 2W11604421A.indb 2 6/16/2022 11:21:20 AM6/16/2022 11:21:20 AM

ENGLISH

11. Allow the appliance to cool completely before putting on or taking off parts, and

before cleaning the appliance.

12. Remove the Flat Beater, Wire Whip, Pastry Beater, Flex Edge Beater, Double Flex

Edge Beater or Spiral Dough Hook from the Stand Mixer before washing.

13. To avoid product damage, do not use the Stand Mixer bowls in areas of high

heat such as an oven, microwave, or on a stovetop.

14. Do not use the Stand Mixer on or next to an electric or gas oven, or put it inside

of a warm oven.

15. If the power cord is damaged, it must be replaced by the manufacturer or its

service agent or by qualified personnel to avoid any risk.

16. Children must be supervised to ensure that they do not use the appliance as a

toy.

17. Do not touch hot surfaces. The surface of the heating element is subject to

residual heat after use. Use handles/knobs/buttons.

18. Do not use the device for any other use other than that for which it was

designed. Improper use of the appliance may lead to possible personal injury.

19. Unplug the appliance from the outlet when not in use and before cleaning. Let

the appliance cool down before adding or removing components and before

cleaning.

20. Refer to the “Care and Cleaning” section for instructions on cleaning the

surfaces in contact with food.

21. This appliance is intended for use in the home and for similar applications, such

as the following:

a) By kitchen staff in retail areas, offices and other work environments;

b) Country houses;

c) By clients in hotels, motels or other residential-type settings;

d) Bedroom or dining room settings.

22. Do not use the appliance for any other use other than that for which it was

designed. It could lead to possible injury.

PRODUCT SAFETY

SAVE THESE INSTRUCTIONS

This product is designed for household use only.

W11604421A.indb 3W11604421A.indb 3 6/16/2022 11:21:20 AM6/16/2022 11:21:20 AM

Electrical Shock Hazard

Plug into an earthed outlet.

Do not remove earth prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these

instructions can result in

death, fire, or electrical shock.

ELECTRICAL REQUIREMENTS

Voltage: 127 V & 220 V

Frequency: 60 Hz

NOTE: The power rating for your Stand

Mixer is printed on the serial plate.

Use an appropriate outlet to plug in your

Stand Mixer. If the plug does not fit in the

outlet, contact a qualified electrician. Do

not modify the plug in any way. Do not

use adapters or T’s.

Do not use an extension cord. If the

power supply cord is too short, have a

qualified electrician or service person

install an outlet near the appliance.

The maximum rating is based on the

attachment that draws the greatest

load (power). Other recommended

attachments may draw significantly less

power.

PRODUCT SAFETY

Electric outlet:

For your safety and to avoid damage to

your product, it is very important that your

product is earthed correctly.

Your appliance power cord features a

hexagon-shaped plug, 10A, per ABNT

(NBR 14136).

Your residence electrical installation must

have a suitable electric outlet for this type

of plug. If not, it is your responsibility to

have one installed by a qualiﬁed electrician.

Use appropriate outlet type for your

appliance plug, as shown below:

Before operating this

appliance, make sure

the main voltage at

the installation site is

the same as indicated

on product technical

data label.

This information is also included on the

label attached to your appliance’s cord

near the plug.

IMPORTANT:

• If it is necessary to convert your 127V

appliance to 220V, use a 1.0 KVA

stabiliser.

• If it is necessary to convert your 220V

appliance to 127V, use a 1.0 KVA

stabiliser.

• Never plug your

appliance into

multiplug adapters

with another

appliance in the same

socket. Do not use an

extension cord. This type of connection

may cause electrical overload in the

mains, and can damage the appliance

and could cause a ﬁre. The appliance

should be plugged into its own outlet.

• In case of oscillation in mains voltage,

install an automatic voltage stabiliser

with minimum rating of 1500 Watts

between the appliance and the socket.

• If the cord of this appliance is damaged,

it must be replaced. Contact your

nearest authorised KitchenAid Customer

Care Centre.

W11604421A.indb 4W11604421A.indb 4 6/16/2022 11:21:20 AM6/16/2022 11:21:20 AM

ENGLISH

ACCESSORY/SPEED GUIDE

ACCESSORY USE FOR DESCRIPTION SPEED

Flat Beater

Mixing and

folding

ingredients

Folding delicate ingredients, egg

whites, cream, etc. Mixing cakes,

frostings, cookies, etc.

1∕2speed for folding

speeds 1-6 for mixing

Flex Edge Beater*,

Double Flex Edge

Beater*

Mixing and

creaming

ingredients

Creaming butter and sugar, mixing

cakes, frostings, cookies, etc. speeds 1-6

Spiral Dough Hook Kneading Breads, rolls, pizza dough, etc. speed 2

Wire Whip*/11-Wire

Stainless Steel Elliptical

Whip* Whipping Eggs, Egg whites, cream, etc. speeds 4-10

Pastry Beater*

Cutting butter

into ﬂour,

mashing fruits/

vegetables,

shredding

meats

Pie dough and other pastries;

mashed potatoes/fruits/vegetables,

shredded chicken

Pastries (Cutting

butter into ﬂour):

speed 1-3,

Mashing fruits/

Vegetables: Up to

speed 2

Mashing potatoes,

Shredding Meat:

speed 2

NOTE: Use Speed 2 to mix or knead yeast doughs. Use of higher speed creates high potential for Stand

Mixer failure. The PowerKnead™ Spiral Dough Hook efficiently kneads most yeast dough within 4 minutes.

The use of a lower speed might slow down the unit and not thoroughly knead the dough.

*Available as an accessory purchase with selected models only.

W11604421A.indb 5W11604421A.indb 5 6/16/2022 11:21:20 AM6/16/2022 11:21:20 AM

PRODUCT ASSEMBLY

IMPORTANT: If the Bowl is not securely snapped into place, it will be unstable and

wobble during use.

To attach the Accessory: Slip the

accessory onto the shaft. Turn to hook it

over the Pin on the shaft.

To Remove the Accessory: Turn Stand

Mixer to “0” (OFF) then unplug. Press

accessory upward and turn to the left. Pull

down the accessory from Beater Shaft.

Turn the Stand Mixer to “0” (OFF) and

then Unplug.

To attach the Bowl: Fit the Bowl

Supports over Locating Pins and press

down on back of the Bowl

until Bowl Pin

snaps into Spring Latch.

Spring Latch

Locating Pin

0 .5 1 2 3 4 5 6 7 8 9 10

To Remove Bowl: Place Bowl-Lift Lever

in the down position. Grasp Bowl Handle

and lift straight up and off Locating Pins.

To raise the Bowl: Rotate the

Bowl-Lift Lever to the straight up

position. The Bowl must always be in the

raised position when mixing.

Test the Beater to Bowl Clearance: Turn

Stand Mixer ON and test each speed,

making sure the beater does not touch

the Bowl during operation. If the Beater

is too far away from the bottom or is

hitting the Bowl, proceed to next step to

make adjustments.

W11604421A.indb 6W11604421A.indb 6 6/16/2022 11:21:21 AM6/16/2022 11:21:21 AM

ENGLISH

(OPTIONAL) To adjust Beater to Bowl

Clearance: Lower the Bowl to the

down position. Turn the screw slightly

counterclockwise (left) to raise the beater,

or clockwise (right) to lower it. Adjust the

beater so that it just clears the surface of

the Bowl. Check again the clearance of

the beater to the Bowl.

Raise Bowl

Lower Bowl

Lower Bowl IMPORTANT: When properly adjusted,

the Flat Beater will not strike on the

bottom or sides of the Bowl. If the Flat

Beater or the Wire Whip is so close that

it strikes the bottom of the Bowl, coating

may wear off the beater or wires on the

whip may wear.

*Available with select models only and available as an accessory purchase.

PRODUCT USAGE

1. Turn the Stand Mixer to “0” (OFF) and then Unplug.

2. Attach Bowl and Flat Beater, Dough Hook, or Wire Whip* to the mixer. Attach Bowl

and raise into locked position.

3. Place the shield onto the Bowl so that the Motor Head covers the U-shaped gap in

the shield. This will position the pouring chute just to the right of the Attachment Hub

as you face the Mixer. Press lightly so that the tabs snap the shield onto the Bowl.

4. Pour ingredients into the Bowl through the Pouring Chute.

USING THE POURING SHIELD*

DISASSEMBLING THE PRODUCT

1. Turn the Stand Mixer to “0” (OFF) and then Unplug.

2. Lift the front of the Pouring Shield* clear of the rim of the Bowl. Pull away from the

Stand Mixer. Lower the Bowl and scrape.

PRODUCT ASSEMBLY

W11604421A.indb 7W11604421A.indb 7 6/16/2022 11:21:21 AM6/16/2022 11:21:21 AM

PRODUCT USAGE

WARNING

Injury Hazard

Unplug mixer before touching

beaters.

Failure to do so can result in

broken bones, cuts, or bruises.

Electrical Shock Hazard

Plug into an earthed outlet.

Do not remove earth prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these

instructions can result in

death, fire, or electrical shock.

1. Plug the Stand Mixer into a grounded

3 prong outlet. Start with lower speed

to avoid splashing and increase it

gradually. Refer to the “Speed Control

Guide”.

2. Do not scrape the Bowl while operating.

Scraping the Bowl once or twice during

mixing is usually sufﬁcient.

OPTIONAL ATTACHMENTS

KitchenAid offers a wide range of optional attachments such as the Spiralizer, Pasta Cutters,

or Food Grinder that may be attached to the Stand Mixer attachment power hub.

Turn the Stand Mixer to “0” (OFF) and

then unplug. Unscrew Attachment

Hub Cover. Insert attachment into

Attachment Hub, making certain that

attachment power shaft ﬁts into the

square Attachment Hub socket.

Tighten the Attachment Knob by turning

it clockwise until the attachment is

secured to the Stand Mixer.

NOTE: See the “Use and Care Guide” of each specific attachment for more details.

W11604421A.indb 8W11604421A.indb 8 6/16/2022 11:21:22 AM6/16/2022 11:21:22 AM

ENGLISH

IMPORTANT: Do not immerse the Stand Mixer body in water or other liquids.

Allow the appliance to cool completely before putting on or taking off parts, and

before cleaning the appliance.

CARE AND CLEANING

1. Turn the Stand Mixer to “0” (OFF) and then Unplug.

2. Wipe the Stand Mixer Body with a soft, damp cloth.

3. The Bowl is full dishwasher-safe.

The following parts are dishwasher-safe, top rack only: Flat Beater, Flex Edge Beater*,

Double Flex Edge Beater*, Spiral Dough Hook, 11-Wire Stainless Steel Elliptical Whip*,

Pastry Beater*, Scraper* ** and Pouring Shield*.

4. The following part should be hand-washed only, using warm, soapy water and drying

thoroughly: Wire Whip* only.

*Available with select models only and available as an accessory purchase.

**Can also be used to scrape your Bowl.

W11604421A.indb 9W11604421A.indb 9 6/16/2022 11:21:22 AM6/16/2022 11:21:22 AM

TROUBLESHOOTING GUIDE

PROBLEM SOLUTION

If Stand Mixer warms up during

use:

Under heavy loads with extended mixing time periods, you

may not be able to comfortably touch the top of the Stand

Mixer. This is normal.

If Stand Mixer emits a pungent

odor during initial use: This is normal. This is common with electric motors.

If the Flat Beater hits the Bowl: Stop the Stand Mixer. See the “Product Assembly” section

and adjust the Beater to Bowl Clearance.

The Speed Control Lever does

not move smoothly or easily: To move the Speed Control Lever with ease, lift slightly up

as you move it across the settings in either direction.

If your Stand Mixer should fail

to operate, please check the

following:

Is the Stand Mixer plugged in?

Is the fuse in the circuit to the Stand Mixer in working

order? If you have a circuit breaker box, be sure the circuit

is closed.

Turn off the Stand Mixer for 10-15 seconds, then turn it

back on. If the Stand Mixer still does not start, allow it to

cool for 30 minutes before turning it back on.

If product shuts off after

extensive use:

Motor has automatic sensor that will keep motor from

overheating by shutting it off. If this occurs, turn speed

switch to off and let Stand Mixer rest for 30 minutes before

restarting.

If mixer is slowing down or

appearing to struggle:

Are you using the appropriate beater and speed? See

“Accessory/Speed Guide“ for more information. Using

1/2 Speed or Speed 1 for bread doughs and heavy loads

might slow down the unit. Breads should knead with the

dough hook at Speed 2. If you have slowdown with heavy

loads at 1/2 Speed, increase to Speed 1 or 2.

If the problem cannot be

corrected:

See the “Warranty and Service” section.

Do not return the Stand Mixer to the retailer; retailers do

not provide service.

WARNING

Electrical Shock Hazard

Plug into an earthed outlet.

Do not remove an earth prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, re,

or electrical shock.

For customers in the US, please visit kitchenaid.com/pinch-of-help for additional product help.

and elsewhere. Used under license in Canada.

W11604421A.indb 10W11604421A.indb 10 6/16/2022 11:21:22 AM6/16/2022 11:21:22 AM

This manual suits for next models

Table of contents

Languages:

Other KitchenAid Kitchen Appliance manuals

KitchenAid

KitchenAid 5KCF0201A User manual

KitchenAid

KitchenAid KAC-22 User manual

KitchenAid

KitchenAid KMC4241 Assembly instructions

KitchenAid

KitchenAid 5KGB User manual

KitchenAid

KitchenAid KESMK4 User manual

KitchenAid

KitchenAid KF26M22 User manual

KitchenAid

KitchenAid KSM1CB User manual

KitchenAid

KitchenAid KBCS24 Parts list manual

KitchenAid

KitchenAid 5FT User manual

KitchenAid

KitchenAid Ceramic Bakeware User manual

KitchenAid

KitchenAid KSM1CB User manual

KitchenAid

KitchenAid KHBV53 User manual

KitchenAid

KitchenAid 5KSM1APC User manual

KitchenAid

KitchenAid 5KSMSFTA User manual

KitchenAid

KitchenAid KMC4241 User manual

KitchenAid

KitchenAid KSMTHPS User manual

KitchenAid

KitchenAid KPCA Quick guide

KitchenAid

KitchenAid KUBL204E User manual

KitchenAid

KitchenAid 780-0018 Product information sheet

KitchenAid

KitchenAid 5KPEXTA Quick guide

KitchenAid

KitchenAid KSMSCA User manual

KitchenAid

KitchenAid W11563953A User manual

KitchenAid

KitchenAid KSM200 Series User manual

KitchenAid

KitchenAid 5KHBV53 User manual

Popular Kitchen Appliance manuals by other brands

Tayama

Tayama TYG-35AF instruction manual

AEG

AEG 43172V-MN user manual

REBER

REBER Professional 40 Use and maintenance

North American

North American BB12482G / TR-F-04-B-NCT-1 Assembly and operating instructions

Presto

Presto fountain popper instruction manual

Westmark

Westmark 1035 2260 operating instructions

Zanussi

Zanussi ZCG64396XA user manual

HOFFEN

HOFFEN SM-9302M instruction manual

Philips

Philips HD3133 user manual

Ronco

Ronco Beef Jerky User guide and recipes

Hendi

Hendi 470411 user manual

Livoo

Livoo MEN386 user manual

Vogue

Vogue D446 instruction manual

croydon

croydon WR-10313-700 instruction manual

ADE

ADE AUTOMATIC-L operating instructions

Chefman

Chefman RJ43-SQ Series user guide

Vacmaster

Vacmaster VP680 user guide

Jetmaster

Jetmaster 900HG operating instructions