Kamstrup 382 User manual

Manual

Kamstrup 382

www.kamstrup.com

Operating instructions

Connect the meter in accordance with the installation diagram on the meter’s type label.

Depending on the configuration a fixed value will be displayed, or the display will

change between selected indications every 10 seconds.

It is possible to change the display reading manually by activating the push button on

the meter. The available readings will depend on the meter’s configuration.

Security and installation guidelines

The meter shall only to be used for measuring electrical energy and shall operate within

the specified values only.

The meter must be switched off when working on it. It can be highly dangerous to touch

the meter parts when the meter is switched on.

Therefore, the relevant security fuse must be removed and kept in a place where it cannot

be inserted by unauthorized persons.

Current local standards, guidelines, regulations and instruction must be observed. Only

authorized personnel is permitted to install electricity meters.

Meters for direct connection must be protected against short circuit by a security fuse in

accordance with the maximum current stated on the meter.

The meter constant LED blinks proportionally to the consumed active energy.

Only authorized personnel must break the utility sealing.

LCD-displayLCD-display

LED (meter constant)LED (meter constant)

Optical interfaceOptical interface

Push buttonPush button

Type labelType label

The phase indications L1, L2 and L3 have more than one function, they indicate one of

three situations described below:

Segments L1- L3 Indicate

On Both voltage and load above minimum limit.

Active phases indicate consumption.

Off The voltage is below minimum limit.

Blinking Segments L1 – L3 function as load indicators. Voltage is above and

load is below minimum limit.

The load indicator is active 4 hours after meter reset.

If the load exceeds the minimum limit and the meter is configured with this reading,

consumption will be indicated via the quadrant reading.

The meter’s LED can be used provided that the quadrant indicator is not selected.

The measured unit is displayed in the right side of the display.

Tariff indicating active tariff.

Terminals

Size: 1,5 – 25 mm2

1,5 – 35 mm2

Screw: Pz 2

Torch: 2,5 – 3 Nm

LCD display

L1 L2 L3

T1 T2 T3 T4

7-digit identification field Quadrant reading Status reading

Unit field

Tariff reading

Phase indication

Value field

Installation dimensions

Connection diagrams

The valid connection diagram appears from the type label.

3-phase, 4-wire 3-phase, 3-wire (Aron)

201,6

166,9

684-38A-C4-00-010

Sn:

3 x230/400V

50 Hz

LED/S0:1000 imp/kWh

0,5-5(85)A

Kl. A (3) EN 62053-23

EN 50470 1/3

2007W13

40 +70C

T10063

- -

201,5

166,9

123456789101112

P+

S0 +

20 -

123456789101112

P+

S0 +

20 -

5512-474 GB/04.2007/Rev. A1

Table of contents

Other Kamstrup Measuring Instrument manuals

Kamstrup

Kamstrup ULTRAFLOW 54 DN15-125 Parts list manual

Kamstrup

Kamstrup ULTRAFLOW 54 User manual

Kamstrup

Kamstrup flowIQ 3100 Operating and installation instructions

Kamstrup

Kamstrup flowIQ 3100 Series Parts list manual

Kamstrup

Kamstrup MULTICAL 603 Parts list manual

Kamstrup

Kamstrup 162M Parts list manual

Kamstrup

Kamstrup MULTICAL 302 User manual

Kamstrup

Kamstrup MULTICAL 403 Installation and operating instructions

Kamstrup

Kamstrup MULTICAL 62 Parts list manual

Kamstrup

Kamstrup ULTRAFLOW 54 Series Parts list manual

Kamstrup

Kamstrup 382 User manual

Kamstrup

Kamstrup MULTICAL 6M2 User manual

Kamstrup

Kamstrup MULTICAL 602 Parts list manual

Kamstrup

Kamstrup flowIQ 4200 User manual

Kamstrup

Kamstrup MULTICAL 41 Parts list manual

Kamstrup

Kamstrup MULTICAL 402 Installation and operating instructions

Kamstrup

Kamstrup MULTICAL 402 User manual

Kamstrup

Kamstrup OMNIPOWER User manual

Kamstrup

Kamstrup MULTICAL 803 User manual

Kamstrup

Kamstrup MULTICAL 403 Parts list manual

Kamstrup

Kamstrup 66-99-279 Manual

Kamstrup

Kamstrup MULTICAL 403 Parts list manual

Kamstrup

Kamstrup OMNIPOWER User manual

Kamstrup

Kamstrup MULTICAL 21 Parts list manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual