ENDA ETS762 User manual

Counting inputs

(INA, INB) 3 channels (5V to 30V pulses)

40ms, 20ms, 10ms, 1ms, 0.5ms, 0.1ms, 50 (selectable by programming)ms

* 72x72mm sized.

* 2x6 digits display.

* Easy to use by front panel keypad.

* On and Off times of the input pulses can be selected.

* Sampling time can be adjusted between 0.2s and 16.0s.

* Output can be energized while process value is greater or lower than the

preset value.

* Ti utput operation.

* Display configuration can be adjusted.

* Easy connection by removable screw terminals.

* Haing CE mark according to European Norms.

* Sensor type can be selected as PNP or NPN.

* Selectable functional reset.

* Double set-points control is made by 2 relays outputs.

me delay can be included to the o

* Output can be energized continuously or just for a time interval of 0.1

to 999.9 seconds.

* Decimal point can be adjusted between 1. and 5. digits.

* Prescaler factor can be adjusted between 0.00001 and 999.999 for calibration.

* Parameter access protection on 3 levels

Minimum On and Off times

for pulses

ENDA ETS762 TACHO LINE/SPEED METER

Thank you for choosing ENDA ETS762 TACHOMETER.

INPUTS

Adjustable between 0.2s and 16.0s.

Sampling time

1/5 ETS762-E-03

ENDA

PRESET TACHO/LINE SPEED METER

IN A IN B OUT1 OUT2

PRESET RESET

SET

ETS762

Read this document carefully before using this device. The guarantee will be expired by

damaging of the device if you don't attend to the directions in the user manual. Also we don't

accept any compensations for personal injury, material damage or capital disadvantages.

ENVIRONMENTAL CONDITIONS

Height Max. 2000m

Ambient/storage temperature

Max. relative humidity

0 ... +50°C/-25 ... +70°C (with no icing)

Rated pollution degree

TECHNICAL SPECIFICATIONS

80% up to 31 decreasing linearly 50% at 40 .°C °C

According to EN 60529 Front panel : IP60

Rear panel : IP20

Do not use the device in locations subject to corrosive and flammable gases.

Supply 230V AC +%10 -%20, 50/60Hz or 24V AC ±%10, 50/60Hz or optional 9-30V DC SMPS module.

Power consumption Max. 7VA

2.5mm² screw-terminal connections

Wiring

Date retention

EMC

Safety requirements

EN 61326-1: 1997, A1: 1998, A2: 2001 (Performance criterion B for the EMC standard)

EEPROM (Min. 10 years)

EN 61010-1: 2001 (pollution degree 2, overvoltage category II)

ELECTRICAL CHARACTERISTICS

OUTPUTS

Control output (OUT1) Relay : 250V AC, 2A (for resistive load), NO+NC

Control output (OUT2)

Open collector output (S.S. OUT1): Max. 30V DC, 100mA.

Relay : 250V AC, 2A (for resistive load), NO+NC

Auxiliary power supply

Open collector output (S.S. OUT2): Max. 30V DC, 100mA.

12V DC, Max. 50mA (without regulation)

.Mechanical 30.000.000 operation; Electrical 300.000 operation

Life expectancy for relays

Note : Relay and S.S.OUT outputs are in synchronization . When OUT1 relay is energized S.S. OUT1 transistor goes into saturation.

Similarly, when OUT2 relay is energized S.S. OUT2 transistor goes into saturation.

HOUSING

Housing type Suitable for flush-panel mounting according to DIN 43 700.

Dimensions W72xH72xD97mm

Weight Approx. 405g (after packing)

Enclosure material Self extinguishing plastics

While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive materials must not be used.

PNP: 5V to 30V pulse with adjustable pulse time between 2ms and 50ms.

NPN: GND terminal is connected to the RESET IN or HOLD IN terminal.

RESET and HOLD inputs

Accuracy ±%0.1

Supply Voltage Order Code

230V AC +%10 -%20 ETS762

24V AC ±%10 ETS762-24AC

9-30V DC SMPS module ETS762-12AC

TERMS

( 2 ) Digital display

( 4 ),( 5 ),( 6 ),( 7 ) Keypad

Panel cut-out

Connection

cables

Depth

97mm 75mm

84mm

DIMENSIONS

68 mm

+0.7

68 mm

+0.7

Rubber packing

Flush mounting

clamp

Panel

72mm

78mm

2/5 ETS762-E-03

ENDA

PRESET TACHO/LINE SPEED METER

IN A IN B OUT1 OUT2

PRESET RESET

SET

ETS762

ENDA

PRESET TACHO/LINE SPEED METER

IN A IN B OUT1 OUT2

PRESET RESET

SET

ETS762

3HOLD IN

4 RESET IN

5 S.S. OUT2

6 S.S. OUT1

7 IN B

8 IN A

9 GND

10 +12V 50mA

OUT1

AC 250V 2A

RESISTIVE

LOAD

OUT2

AC 250V 2A

RESISTIVE

LOAD

ENDA

INDUSTRIAL

ELECTRONICS

ETS762

SN: XXXXXXXXX

230V AC +10% -20%

50/60Hz 7VA

3HOLD IN

4 RESET IN

5 S.S. OUT2

6 S.S. OUT1

7 IN B

8 IN A

9 GND

10 +12V 50mA

OUT1

AC 250V 2A

RESISTIVE

LOAD

OUT2

AC 250V 2A

RESISTIVE

LOAD

ENDA

INDUSTRIAL

ELECTRONICS

ETS762-24AC

SN: XXXXXXXXX

24V AC ±10%

50/60Hz 7VA

input

type

Set.dsp.

config

Digital display (1) : 9.1mm

Digital display (2) : 7.1mm

4 red LEDs

6 digits, seven segment red LED

6 digits, seven segment yellow LED

Micro switch

Character height

( 3 ) State indicators

( 1 ) Digital display

- Push up the flush-mounting

clamp in direction 1as

shown in the figure above.

- Then, pull out the clamp in

direction 2.

For removing mounting clamps:

Note 1) While panel mounting, additional distance required for

connection cables should be considered.

2) Panel thickness should be maximum 10mm.

3) If there is no 90mm free space at back side of the device,

it would be difficult to remove it from the panel.

CONNECTION DIAGRAM

ENDA ETS762 is intended for installation in control panels. Make sure that the device is used only for intended

purpose. During an installation, all of the cables that are

connected to the device must be free of energy. The device must be protected against inadmissible humidity,

vibrations, severe soiling and make sure that the operation temperature is not exceeded. All input and output

lines that are not connected to the supply network must be laid out as shielded and twisted cables. These cables

should not be close to the power cables or components.

The shielding must be grounded on the instrument side.

The installation and electrical connections must be

carried on by a qualified staff and must be according to the relevant locally applicable regulations.

184-253V AC

50/60Hz 7VA

Switch

Fuse

F 100 mA

250V AC

Neutral

Line

SUPPLY :

NOTE :

Fuse should

be connected.

230V AC Supply

Cable size: 1,5mm²

1) Mains supply cords shall meet the requirements of IEC 60227

or IEC 60245.

2) In accordance with the safety regulations, the power supply

switch shall bring the identification of the relevant instrument

and it should be easily accessible by the operator.

Note :

Holding screw 0.4-0.5Nm Equipment is protected throughout

by DOUBLE INSULATION.

(3) State indicators shows the state of the device.

(7) Used for selecting run or programming modes or for adjusting parameters.

(4) Used for adjusting the preset values in the run mode.

Increment or parameter selection key during programming mode.

(5) Decrement or reset key in the run mode.

Decrement or parameter selection key during programming mode

(6) Used for selecting preset1, preset2 or user defined message in the run mode.

Used for selecting oPtion. s or parameter to be changed in the programming mode.

(2)

The value of the parameter selected by parameter during run mode.

Parameter value during programming mode.

(1) The value of the measurement selected by parameter during run mode.

Parameter name during programming mode.

PRESET

SET

Run mode

Process value defined by the parameter is shown on the top display.

Variable selected by the parameter is shown on the bottom

Preset value for out1.

See NOTE 1 for programming.

Preset value for out2.

See NOTE 1 for programming.

PRESET

outPut

oPtýon. PRESET

dýsP.

oPtýon.

SEcur.

oPtýon.

There are eight different input types.

Measurement methods for different input

types are on the next page.

See NOTE 2 for adjustment.

Minimum On and Off times for the input

pulses can be selected.

See NOTE 2 for adjustment.

Sensor type can be selected.

See NOTE 2 for adjustment.

There are 4 different output types for out1 and out2.

If output type is selected lo, output is energized under

prset value. In contrary, if it

is selected Hi, output is

energized over prset value.

See NOTE 2 for adjustment.

out1 pulse time can be adjusted between 0.1 and 999.9s .

If it is adjusted to 0.0, out1 is energized continuously when

process value reaches PrSEt1 value.

.See NOTE 1 for adjustment

out2 pulse time can be adjusted between 0.1 and 999.9s .

If it is adjusted to 0.0, out2 is energized continuously when

process value reaches PrSEt2 value.

See NOTE 1 for adjustment.

A time delay between 0.0 and 999.9s can be included to the

operation of out1. If process value do not stay over prset1

value for a time interval less than time delay, out1 will not be

energized.

See NOTE 1 for adjustment.

A time delay between 0.0 and 999.9s can be included to the

operation of out2. If process value do not stay over prset2

value for a time interval less than time delay, out2 will not be

energized.

See NOTE 1 for adjustment.

RESET

Calibration (prescaler) value can be adjusted between 0.00001

and

To change the position of decimal point, press and

keys for 0,6s.

999.999. Process value is multiplied by prescaler value

and the result is displayed on the screen.

See NOTE 1 for adjustment.

Decimal point can be adjusted between 1. and 5. digits.

If desired, decimal point is not included.

See NOTE 2 for adjustment.

Display configuration can be selected.

See NOTE 2 for adjustment.

Measurement unit, a message, a constant etc. should be entered

by the user.

See NOTE 1 for adjustment.

If the duration of the pulses at the input is

shorter than the selected minimum pulse time,

this error message appears.

IN A

If the duration of the pulses at the input IN B is

shorter than the selected minimum pulse time,

the error message appears.

If no signal is detected at the input AIN during the

selected limit time, this error message appears.

If no signal is detected at the input IN B during the

selected limit time, this error message appears.

If both IN A and IN B are required in a measurement

methods and no signal is detected at the both inputs

during the selected limit time, this error message

appears.

Overflow error.

Indicates that process value

was greater than 999 999.

RESET RESET

The time base used changes depending

on the selected measurement method.

See NOTE 2 for adjustment.

Sampling time can be selected.

Sampling time defines the time interval

for successive refreshing of the display.

See NOTE 2 for adjustment.

If no input signal is detected during the

defined limit time, an error message

appears on the display.

See NOTE 2 for adjustment.

Minimum pulse time for the external

reset input can be selectable.

See NOTE 2 for adjustment.

PARAMETER TABLE

output oPTIoN.

DisP. oPTIoN.

SEcur. oPTIoN.

inPut

typE

input

t.base

micro

second

meter

per.sec.

rotate

per.sec.

meter

per.min.

rotate

per.min.

meter

per.hr.

rotate

per.hr.

mili

second

0.1

second

Tacho.

inA-inB.

ratio

in1-in2.

ratio

line

speed.

line

speed.

period

time

inter

out1.lo.

out2.lo.

out1.Hi.

out2.Hi.

out1.Hi.

out2.lo.

out1.lo.

out2.Hi.

time

inter

PUls

time

PUls

time

Count.

per.pls.

Count.

per.Cyc.

dEci.

Point

output

config

diSP.

CAL.

out1

PULs.ti.

set.dsp.

config. prset1 prset2

User

define

out2

pUls.t2

User

define.

inP.opt

seCUr.

dSP.oPt.

seCUr.

out.oPt.

seCUr.

nonE

Prog.

yES

nonE

Prog.

yES

nonE

Prog.

Panel

reset

Prog.

yES

reset

input

SEcur.

codE 1111

0 0.0 0.00 0.000 0.0000 0.00000

000..0

0.00001

.............

999.9

999.999

dEFAuL.

SEt.

disp.

resEt.

yES

reset

both

3/5

SET

99999

100000

PrSEt1

100000

PRESET

RESET

ýnPut

oPtýon.

out1

del.ti

out2

del.ti

prset1

equ.

prset1 Pr2.sub

pr1

input oPTIoN.

reset

puls

0.002

second

0.005

second

0.010

second

0.020

second

0.050

second

limit

time 1

0.2

100

16.0

0.04

second

0.02

second

0.01

second

0.001

second

0.0005

second

0.0001

second

0.00005

second

npn pnp

Puls

time

sensor

type

sample

time

ETS762-E-03

PrSEt2

150000

input

type

input

type

RESET

output

config.

input

t.base

Puls

time

Sensor

type

sample.

time

Limit

time

reset

puls

RESET RESET

RESET

deci.

point.

secur.

Code.

inp.opt.

seCUr.

out.opt.

seCUr.

dsp.opt.

seCUr.

disp.

reset

defaul.

set

puls

err.ýna

puls

err.ýnb

ýna no

puls

ýnb no

puls

ýna.ýnb.

no.puls

HýgH.

input

RESET

disp.

CAl

RESET

set.dsp.

config.

set.dsp.

config.

User.

define.

RESET

out1

pUls.tý

RESET

out2

PUls.tý

RESET

out1

del.tý

RESET

out2

del.tý

prset1

eqU.

This menu appers, If or is selected

as input type input.

This menu appers, If , or is

selected as input type.

This menu appears if selected as input type.

Measurement unit, a message, a constant etc. entered by the user appears.

ERROR MESSAGES

PRESET

SET

if key is pressed while holding key, the

programming mode is entered.

Pr2.Sub.

Pr1

= Output is energized when measured value reaches PrSEt1

value.

= The difference between PrSEt2 and PrSEt1 becomes the new

value of PrSEt1'. It means -

Now, o

PrSEt1 (new) = PrSEt2 PrSEt1(old).

utput is energized when process value reaches

PrSEt1(new) value.

See NOTE 2 for adjustment.

PrSEt1

Access code for entering security option menu.

This parameter should be 1111.

See NOTE 2 for modification.

Prog.

yES

Prog.

yES

nonE

Prog.

reset

both

See NOTE 2. for modification.

PAnE.

reSEt

inPut.

While leaving the programming mode,

no = All the modifications are saved.

Yes = Default values are set to parameters.

See NOTE 2. for modification.

Prog.

yES

nonE

Prog.

= No menu is seen.

See NOT 2. for adjustment.

= Menu is seen but can not be programmed.

= Menu is seen and programming is possible.

= Menu is seen but can not be programmed.

= Menu is seen and programming is possible.

= Menu is seen but can not be programmed.

= Menu is seen and programming is possible.

= Display can not be reset.

= Both RESET input and the key can

be used for resetting.

= Display

= Display can be reset by the RESET input.

can be reset by key.

RESET

PARAMETER ADJUSTMENT METHOD

To modify non-mumerical parameters, hold key and use keys.

SET

RESET

SET

PRESET RESET

SET

RESET

SET

NOTE 1

NOTE 2

Holding key the value of the selected parameter is seen on the display. While holding key, the value of the selected parameter can be

changed by using keys. In order to reset all the digits, first press and hold key. And then, press both and keys together.

SET SET SET SET

SET

1.00000

1.01000

1.00000

PRESET RESET

PRESET

Selected

numerical

parameter

MEASUREMENT METHODS ACCORDING TO INPUT TYPES

inPut

tyPE

tacho

inA.inb

ratio

Line

speed

time

inter.

pUls

time.

Count

per.pls.

Count

per.CYc.

period

IN A input

IN inputA

IN B input

IN inputB

HOLD IN input

IN inputB

IN Binput

RESET IN

8910

8 9 10 11 12 13

Note: should be selected according to the minimum On and Off times of the input pulses.

Revolution measurement method (rpm: revolution/minute)

4/5 ETS762-E-03

Process value

Previous value

process value do not changes

(T1+T2+ ..... +Tn)/n

Counting value: 9

Counting value : 13

(1/T1x60) rpm

(1/Ta) / (1/Tb)

(1/T1x60)m/dk.

(1/T2x60)m/dk.

T2.

(1/T3x60)m/dk.

(1/T2x60) rpm (1/T2x60) rpm

sampling time

T3 T4

ZERO

Tb Tb Tb Tb

Ratio of the revolutions of IN A and IN B

Speed measurement method

Time difference measurement method

Pulse duration measurement method

Pulse counting method

Period measurement method

second

out1.Hi

out2.Hi

999,999

Reset

Preset1

Out1

Out2

Preset2

out1

del.ti

out2

del.ti

out1.lo

out2.lo

999,999

Reset

Preset2

Out1

Out2

Preset1

out1

del.ti

out1

del.ti

out2

del.ti

out2

del.ti

out1.Hi.

out2.lo.

999,999

Reset

Preset2

Out1

Out2

Preset1

out1

del.ti

out2

del.ti out2

del.ti

out1.lo.

out2.Hi.

999,999

Reset

Preset1

Out1

Out2

Preset2

out1

del.ti

out2

del.ti

out1

del.ti

OUTPUT TYPES

T³20ms

Td³20ms

out2

puls.ti. out2

puls.ti.

Adjusting or to a value between 0.1 and 999.9 seconds,

a pulse output is obtained.

Adjusting or to 0.0, a continuous output is obtained.

out1

Puls.ti. out1

puls.ti.

Puls

time

Puls

time

Puls

time

Puls

time

Puls

time

Puls

time

Puls

time

Puls

time

output

config.

output

config.

output

config.

output

config.

PNP PROXIMITY SWITCH

GND

OUT

+ 12V

PNP PROXIMITY SWITCH

GND

+ 12V

GND

OUT

TYPICAL SENSOR CONNECTIONS

TERMINAL CONNECTIONS

Terminal descriptions

3 : Hold input

4 : Reset input

5 : Solid state out2 (Max 30V 100mA open collector NPN)

6 : Solid state out1 (Max 30V 100mA open collector NPN)

7 : IN A input (Max 30V 10kHz)

8 : IN B i input (Max 30V 10kHz)

9 : GND

10 : +12V 50mA auxiliary power supply

11,12 : SUPPLY inputs

13,14,15 : 1. relay output (Max 2A 250V AC)

16,17,18 : 2. relay output (Max 2A 250V AC)

SÝSEL MÜHENDÝSLÝK ELEKTRONÝK SAN. VE TÝC. A.Þ.

Yukarý Dudullu 34775 - ÜMRANÝYE/ÝSTANBUL-TÜRKÝYE

Tel : +90 216 499 46 64 Pbx. Fax : +90 216 365 74 01

url : www.enda.com.tr

Barbaros Cad. Kutup Sok. No:20

5/5 ETS762-E-03

230V AC Supply

Switch

Cable size: 1,5mm²

Fuse

F 100 mA

250V AC

230V AC Supply

Switch

Cable size: 1,5mm²

Fuse

F 100 mA

250V AC

3HOLD IN

4 RESET IN

5 S.S. OUT2

6 S.S. OUT1

7 IN B

8 IN A

9 GND

10 +12V 50mA

OUT1

AC 250V 2A

RESISTIVE

LOAD

OUT2

AC 250V 2A

RESISTIVE

LOAD

ENDA

INDUSTRIAL

ELECTRONICS

ETS762

SN: XXXXXXXXX

230V AC +10% -20%

50/60Hz 7VA

3HOLD IN

4 RESET IN

5 S.S. OUT2

6 S.S. OUT1

7 IN B

8 IN A

9 GND

10 +12V 50mA

OUT1

AC 250V 2A

RESISTIVE

LOAD

OUT2

AC 250V 2A

RESISTIVE

LOAD

ENDA

INDUSTRIAL

ELECTRONICS

ETS762

SN: XXXXXXXXX

230V AC +10% -20%

50/60Hz 7VA

3HOLD IN

4 RESET IN

5 S.S. OUT2

6 S.S. OUT1

7 IN B

8 IN A

9 GND

10 +12V 50mA

OUT1

AC 250V 2A

RESISTIVE

LOAD

OUT2

AC 250V 2A

RESISTIVE

LOAD

ENDA

INDUSTRIAL

ELECTRONICS

ETS762

SN: XXXXXXXXX

230V AC +10% -20%

50/60Hz 7VA

NOTE: NPN PROXIMITY SWITCH connection is the same as PNP PROXIMITY SWITCH connection.

Table of contents

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual