SET SET SET
d.PNt..=Display decimal point parameter
Decimal point can be adjusted between 1. and 3. digits.
See NOTE 1 for programming.
L.ScL..=
Scale the lower value of the output,based on parameter
selection, it is 0V,0mAor 4mA
See NOTE 1 for programming.
Lower value of the scale.Adjustable between-1999
H.SCL. and
( ).-10 o.tYP.
H.ScL..= Upper value of the scale.
Adjustable between ( +10) andL.SCL. 9999.
Scale the upper value of the output based on, parameter
selection;it is 10V or 20 mA. and difference can
not be greater than 9999.See NOTE 1 for programming.
otYP.
H.SCL. L.SCL.
Lo.Li..=
See NOTE 1 for programming.
The lower limit of the preset value.
Adjustable between and L.ScL. Hi.Li.( -10).
Hi.Li..=
See NOTE 1 for programming.
The upper limit of the preset value.
Adjustable between and(L.o.li. H.SCl.+10)
o.E.ty. Adjusted type of the output to preset value with button.=
dSAb.
Enb.
S.on
= Output can not be adjusted to preset value with button.
= Output can be adjusted to preset value with button.
= Output is increased to voltage that set value is displayed with button during
See NOTE 1 for programming. r.tI
o.d.ty. Adjusted type of the output to lower limit value with button.=
dSAb.
Enb.
S.oFF
= Output can not be adjusted to lower limit value with button.
= Output can be adjusted to lower limit value with button.
= Output is increased to voltage that lower limit value is displayed with button
during
See NOTE 1 for programming.
dtI.
P.on.C.= Selection of the output parameter behavior
key is pressed while holding down to key
the programming mode is entered
r.ti. = Increasing time for output.
Adjustable between 1-250 seconds.Output is
increased slowly to the lower limit value
during adjusted time.
See NOTE 1 for programming.
d.ti. = Decreasing time for output value.
Adjustable between 1-250 seconds.
Output is decreased slowly the lower limit
value during adjusted time.
See NOTE 1 for programming.
Pi.rt.. = Increasing and decreasing speed
of preset value.
It is adjustedI dSAb.
dSAb , ,100 0
values. is selected,the preset value
can not be changed.
Selected according to the value increase or
decrease the preset buttons for fast switching
mode,the preset value speedy is increased or
decreased “one by one”,10 at each step,100
at each step,1000 at each step.
See NOTE 1 for programming.
1, 10 ve 100
d.Adr.=Device address for ModBus.
Adjustable between 1-247 or selectable
See NOTE 1 for programming
This parameter is active device with communication option.
c.Pot. c.Pot..When is
selected,the device will be master potentiometer and slave
potentiometers can be adjusted dependent on it.
RS485
While the parameter names appear and keys are
pressed together,the program will return to the menu display.
,
Entering from programming mode to run mode:
If no key is pressed within 20 seconds during programming mode data is stored automatically and the run mode is entered.After pressing button and then passed
to the program menu by pressing key is pressed in combination with keys and the information is recorded.
S.Cod =
message
Access code for safety menu.
This parameter should be .
Security code is 0; If key is
pressed continuously for 5 seconds,
is displayed and
return to the factory settings.
2041
dEfP
U.c.Sc.
nonE
P.yEs
P. no
=
=
=
=
U.cnF. menu protection
level parameter.
No menu is seen
Modification feasible
Only traceable
o.tyP...
0-10
4-20
0-20
=
= 0-20mA
See NOTE 1 for programming
Output type selection parameter
= 0-10V output usable
= 4-20mA output usable
output usable
o.C.sc. o.Cnf.
nonE
P.yEs
P. no
= Menu protection
level parameter.
=
=No menu is seen
Modification feasible
= Only traceable
Pno =Menu visible.
d.Pnt.
L.ScL..
H.ScL.
Hi.Li.
d.ADr.
Lo.Li.
bAud
U.CnF..
U.CnF..
o.CnF.
o.cnF.
SECu.
SEcu.
S.Cod.
U.C.sc.
p.YES
Off
DsaB
DsaB
30
30
1
0-10
0
0
9999
0
1
1500
9.60
p.YES
o.typ..
o.C.sc.
pon.C.
o.E.ty.
o.d.ty..
r.ti.
d.ti.
P.i.rt.
SET SET SET
Programming mode
Run mode
baud = RS485Baud rate for the connection.
Adjustable; and .
This parameter is active device with RS485 communication
option.
off,2400,4800,9600,19200 38400
key is pressed whole in the run mode,preset setup mode is entered and PrSt. message is displayed. Message appears when the or button is pressed, the preset value starts to flash. By using
keys ,preset value can be adjusted.Preset value can be adjusted by using external buttons as well.External buttons become disable in programming mode.If the device is also controlled by a potentiometer,
adjustable preset value appears as above.
If and parameters are adjusted to any value expect parameter,
output can be controlled with and buttons.
o.Et.y o.d.t.Y dSAb
Preset
value
Active
output value or 1000 1001 1002 1002
1003
1000 PrSt.
If no key is pressed
for 3 seconds
+
+
= When first energized, output is the voltage or current that lower limit value is indicated.
Attention: If this parameter is selected, the set value that was adjusted before is seen when set button is
pressed at first. In addition,if increasing or decreasing that value is wanted the set value is equalized to
lower limit value and then adjustment can be done.
= When first energized, output is the voltage or current hat the set value is indicated.
= When first energized, output is increased slowly from the voltage or current that lower limit value is
indicated to the voltage or current that set value is indicated during .
See NOTE 1 for programming.
ofF
On
S.Str.
r.ti
For adjusting a selected parameter first press and hold key. Then, by using
keys, adjustment can be made.
Parameter adjustment method
NOTE 1
If increment key is pressed and held 0.6 seconds, the value of the selected parameter
changes rapidly. If waited enough, the value increases 100 at each step. After 1 second following
the release of the key, initial condition is returned. The same procedure is valid for the decrement
key.
SET SET
SET
SET
P.on.C.
o.d.ti.
E.d.ti.
o.E.ty.
E.E.ty.
Lo.li.
Lo.li.
Lo.li.
off
Dsab.
Dsab.
Dsab.
Dsab.
On
Enb.
Enb.
Enb.
Enb.
r.ti.
r.ti.
S.str.
S.ofF
S.ofF
S.on
S.on
r.ti.
d.ti.
d.ti.
E.E.ty. = Returning method of the output to preset value with the external "Up" input.
o.E.tY. is set like the output parameter.
E.d.ty. = Returning method of the output to
preset value with the external "Down" input.
o.d.tY. is set like the output parameter.
DsaB
DsaB
E.E.ty..
E.d.ty..
3. / 3 EDP2041-E-22032019
