ENDA EPV241A User manual

OUTPUTS

Alarm output Relay: 250V AC, 8A (for resistive load), NO+NC

Mechanical 30.000.000 ; Electrical 100.000 operation.

Life expectancy for relay

0 ... +50°C/-25 ... 70°C

HOUSING

Housing type Suitable for flush-panel mounting. (According to DIN 43 700)

Dimensions W xH xD7 mm77 35 1

Weight

Enclosure material Self extinguishing plastics.

ENDA EPV 41 AC/DC VOLTMETER2 A

While cleaning the device, solvents (thinner, benzine, acid etc.) or must not be used.corrosive materials

Approx. 350g (after packing)

* 77 x 3 mm sized.

* 3 digits display.

* Easy to front panel keypad.

* Multifunctional alarm output (NO+NC) for upper and lower

* Measuring type can be selected AC, DC or True RMS.

configure with

limits.

* With insulated rs485 ModBus protocol communication

feature.(optional)

Values between -100V and 100 V can be indicated with one

decimal point.

* For maximum 50V AC/DC measurements;10 times the

sensitivity of the measurement values between -50V and +50V

with two decimal places to show.

Supply 230V AC +10% -20%, 50/60Hz or 24V AC 10% , 50/60Hz or optional 9-30V DC / 7-24V AC 10% SMPS± ±

Power consumption 2.5mm² screw-terminal connections

Wiring

Scale

Sensitivity

ELECTRICAL CHARACTERISTICS

If ; is selected,it isC.InP 500 0V...500V or If C.inP ;50 is selected,it is 0....50V

If ; is selected, it is -500V DC....500V DC or If ; is selected,it is -50V DC....50V DCC.InP 500 C.InP 50

0,01V (If ;50 is selected )C.InP

Max. 5VA

AC and RMS

1. / 4 EPV 41 -E-100520192 A

Accuracy

EMC

Safety requirements

EN 61326-1: 2006

EN 61010-1: 20 (Pollution degree 2, overvoltage category II)10

RMS

DC ±1%

(Full scale) (For square wave form 2%)±

(Full scale)

Input Impedance 870kΩ

Frequency Range

Input Range -500V...500V (If is selected,device breaks down at more than 1250 DC voltages.)

....50V ( is selected,device breaks down at more than 125 DC voltages.)

CINP 500

If cInp 50

-50V ±

±(Full scale) (For square wave form 2%)±

DC , 10Hz - 200Hz (For square wave form 10Hz-70Hz)

Thank you for choosing ENDA EPV 41 AC/DC voltmeter.2

Read this document carefully before using this device. The guarantee will be expired by

device damages if you don't attend to the directions in the user manual. Also we don't

accept any compensations for personal injury, material damage or capital disadvantages.

Technical Specifications

.Do not use the device in locations subject to corrosive and flammable gases

ENVIRONMENTAL CONDITIONS

Ambient/stroge temperature

Max. Relative humidity

Rated pollution degree

Height

Relative humidity for temperatures to relative humidity80% up to 31°C decreasing linearly 50% at 40°C.

According to EN 60529 Front panel : IP6 , Rear panel :5 IP20

Max. 2000m

0,1V (If is selected and higher than -100V or lower than 100V for input values)CINP;500

1V ( )If is selected and lower than -100V or higher than 100V for input valuesCINP 500;

1-Output

R......Relay

None...No relay

2 Supply Voltage- 3-ModBus

230VAC...230V AC

24VAC.....24V AC

SM...........9-30V DC / 7-24V AC

RSI..... Insulated ModBus (optional)

110VAC...110V AC

SETSET

EPV 241A

ENDA

OUT AC DC ACDC

Order Code : EPV241A- - -

E-mail : info@suran-elektronik.de

Internet : www.suran-elektronik.de

Tel.: +49 (0)7451 / 625 617

Fax: +49 (0)7451 / 625 0650

SURAN Industrieelektronik

Dettinger Str. 9 / D-72160 Horb a.N

english

UP.l1

UP.l1 HYS.U+

UP.l1 HYS.U-

LO.l1

LO.l1 HYS.L+

LO.l1 HYS.L-

Out

dly.U

A.out n.c.=

A.out n.o.=

dly.U dly.ldly.l

Input

Dimensions

:Note

71mm

2. / 4 EPV 41 -E-100520192 A

-A

T3T/2

T/2 2T

T3T/2

T/2 2T

T3T/2

T/2 2T

T3T/2

T/2

3T/2

T/2

T3T/2

T/2 2T

T2T

0.308 A

0.386 A

0.000

Aπ

A12

A13

ac Ac.dc

dc (rms)

To remove the device from panel:

-While pushing the the flush-

mounting clamp in direction pull out

it in direction 1,

1) Panel thickness should be maximum

7mm.

2) If there is no 60mm free space at the back

side of the device, it would be difficult to

remove it from the panel.

Panel cut-out

Connection Diagram

SUPPLY:

NOTE :

184-253V AC

50/60Hz 5VA Line

Neutral

Not :e

Cable Size: 1,5mm²;

230V AC

Supply

Switch

Fuse

F 100mA

250V AC

Fuse should be connected.

1) Mains supply cords shall meet the requirements of

IEC 60227 or IEC 60245.

2) In accordance with the safety regulations, the power

supply switch shall bring the identification of the relevant

instrument and it should be easily accessible by the operator.

Faz

Nötr

Equipment is protected throughout by

DOUBLE INSULATION

Holding screw 0.4-0.5Nm.

Panel

Depth

61mm 5mm

Rubber

packing

Flush mounting

clamp

ENDA EPV241A is intended for installation in control panels. Make sure that the device is used

only for intended purpose. The electrical connections must be carried out by a qualified staff

and must be according to the relevant locally applicable regulations. During an installation, all of the

cables that are connected to the device must be free of electrical power. The device must be protected

against inadmissible humidity, vibrations, severe soiling.Make sure that the operation temperature is not

exceeded. The cables should not be close to the power cables or components.

77mm

SETSET

EPV 241A

ENDA

OUT AC DC ACDC

CAT II

1 2 3 4 5 6 7 8 9 10

ENDAINDUSTRIALELECTRONICS

SN: XXXXXXXXX

EPV241A-R-230VAC-RSI

PROGRAMMABLE

AC/DC VOLTMETER

11 12

OUTPUT

250V AC 8A

RESISTIVE LOAD

COM.

8 680407 704934

230V AC +10% -20%

50/60Hz 5VA

Made in Turkey

+Max. 5

AC / DC

00V

0VMax. 5

AC / DC

CAT II

1 2 3 4 5 6 7 8 9 10

ENDAINDUSTRIALELECTRONICS

SN: XXXXXXXXX

EPV241A-230VAC

PROGRAMMABLE

AC/DC VOLTMETER

11 12

8 680407 704903

230V AC +10% -20%

50/60Hz 5VA

Made in Turkey

+Max. 5

AC / DC

00V

0VMax. 5

AC / DC

CAT II

1 2 3 4 5 6 7 8 9 10

ENDAINDUSTRIALELECTRONICS

SN: XXXXXXXXX

EPV241A-230VAC-RSI

PROGRAMMABLE

AC/DC VOLTMETER

11 12

COM.

8 680407 704910

230V AC +10% -20%

50/60Hz 5VA

Made in Turkey

+Max. 5

AC / DC

00V

0VMax. 5

AC / DC

CAT II

1 2 3 4 5 6 7 8 9 10

ENDAINDUSTRIALELECTRONICS

SN: XXXXXXXXX

EPV241A-R-230VAC

PROGRAMMABLE

AC/DC VOLTMETER

11 12

OUTPUT

250V AC 8A

RESISTIVE LOAD

8 680407 704927

230V AC +10% -20%

50/60Hz 5VA

Made in Turkey

+Max. 5

AC / DC

00V

0VMax. 5

AC / DC

i “ ” .If nput type is selected, the measurement terminals 9 and 12 of the terminals must be connected Otherwise the measurement is done incorrectly.C.Inp 500

If ıC np 50input type “ ” is selected, the measurement terminals 10 and 11 of the terminals must be connected.Otherwise the measurement is done incorrectly.

SET

SET SET

Used for .displaying and configuring the selected parameter value

Programming

key

Used for increasing the setpoint value

When held down for a few seconds, and changing parameters.

configured numeric value increases faster.

Used for decreasing the setpoint value

When held down for a few seconds, and changing parameter.

configured numeric value decreases faster.

Increment

key

Decrement

key

EPV 41 PROGRAMMING DIAGRAM2

If both keys are

pressed upper limit

value can be adjusted.

Measurement value

If this key is pressed

upper limit value

appears.

If this key is pressed

upper limit value

appears.

If both keys are

pressed lower limit

value can be adjusted.

ADJUSTING ALARM VALUETHE

y using and keys upper limit value can be adjusted between -500V and 500V.

This parameter can’t be lower than ( ) value.

B ,

If ;it is 50 this parameter adjustable between -50.00V-50.00V.,C.Inp

lo.l1 HYS.l HYS.U+ +

y using and keys upper limit value can be adjusted between -500V and 500V.

This parameter can’t be lower than ( ) value.

B ,

If ;it is 50 this parameter adjustable between -50.00V-50.00V.,C.Inp

UP.L1 - -HYS.l HYS.U

Loc mode; the menu can not be accessed and other functions.

It can be seen only the measured value

Loc

Measurement value

If key is pressed, “unL” mode is entered.

uNL mode; the menu and other functions can be accessed.

unL

Measurement value

If keys are pressed together,revision date,day and month are displayed.

12.03 2013

While the revision date is shown as day/month,if key is pressed the revision date is displayed as year.

Measurement value

If key is pressed, “Loc” mode is entered.

If both & keys are pressed and held for seconds,programming mode is entered3 .If keys are pressed while parameter names are displayed,then it returns to mensured

value made.

Upper limit

value

SET

y using and keys upper limit value can be adjusted between -500V and 500V.

This parameter can’t be lower than ( ) value.

B ,

(lo.l1 HYS.l HYS.U+ +

If this key is pressed

upper limit value

appears.

,SET

If key is pressed, it returns to parameter name.

Hysteresis value

for upper limit

SET

y using and keys hysteresis value for upper limit can be adjusted between 0.0V and

20.0V. This parameter can’t be higher than ( - - ) value.

B ,

Up.l1 Lo.l1 Hys.l

If this key is pressed

hysteresis value ,

for upper limit appears

SET

If key is pressed, it returns to parameter name.

Delay time for

upper limit alarm

SET

y using and keys delay time for upper limit alarm can be adjusted between 0 and

900 seconds.

B ,

If this key is pressed

delay time ,

for upper

limit appears

SET

If key is pressed , it returns to parameter name.

Lower limit

value

SET

y using and keys lower limit value can be adjusted between -500V and 500V.

This parameter can’t be r than ( ) value.

B ,

highe UP.l1 HYS.U HYS.L- -

If this key is pressed

lower limit value

appears.

,SET

If key is pressed, it returns to parameter name.

SET

B ,y using and keys hysteresis value for lower limit can be adjusted between 0.0V and

20.0V. This parameter can’t be higher than ( - - ) value.Up.l1 Lo.l1 Hys.U

If this key is pressed

hysteresis value ,

for lower limit

appears

SET

If key is pressed,it returns to parameter name.

Delay time for

lower limit alarm

SET

y using and key s delay time for lower limit alarm can be adjusted between 0 and

900 seconds.

B ,

If this key is pressed,

delay time for lower

limit appears

SET

If key is pressed ,it returns to parameter name.

Alarm

output position

SET

y using and keys alarm output can be adjusted or If

at alarm condition.

B , state to it is adjusted non.o. N.c. ,

output relay is powered

If this key is pressed

alarm output

appears.

state SET

If key is pressed ,it returns to parameter name.

If ;it is 50 this parameter adjustable between -50.00V-50.00V.,C.Inp

10.0 If ;it is 50 this parameter adjustable between 0.00 and 20.00.,C.Inp

If ;it is 50 this parameter adjustable between -50.00V-50.00V.,C.Inp

If ;it is 50 this parameter adjustable between 0.00 and 20.00.,C.Inp

10.0

Hysteresis value

for lower limit

SET

ENDA

ACDC

ACOUT

EPV 141

SET

ENDA

ACDC

ACOUT

EPV 141

SETSET

EPV 241A

ENDA

OUT AC DC ACDC

PROGRAMMING MODE

3. / 4 EPV 41 -E-100520192 A

Sampling time of the measurement value is shown on the screen. If the selected;sampling time of the measurement is 250ms,

If 2 is selected,it is 500ms.If 3 is selected, it is 750ms.If 1 is selected,it is 1 second.

Optn

If this key is pressed

measuring type

appears.

y using and keys measuring type can be adjusted , orB , to ac dc acdc.Three leds

at the top of the display show measuring type.

Measuring

type

SET

If this key is pressed,

address of the device appears.

Adrs 1

By using and keys address of the device can be adjusted between 1-247.

SET

If this key is pressed,

sampling time measurement

value appears.

SET

Sampling time

measurement value

ACdC

SET

If key is pressed,it returns to parameter name.

SET

If key is pressed, it returns to parameter name.

SET

If key is pressed, it returns to parameter name.

SET

baud OFF

By using and keys, baudrate value of the device can be adjusted to OFF,1200,2400,4800,9600,19200.

SET

If key is pressed,it returns to parameter name.

(*)There are only parameters in the devices those have no relay.

The and parameters are only in the devices those have modbus.(**) AdrS baud

, ,tYPE optn CInp ,

If any key is pressed in 25 seconds or the device is powered down and powered upş,then it returns to operation mode.

NOTE:

If key is held down while the device is powered up, the message will appear and the factory settings will be restored.d.PAr

Means, measured current value is higher than scale.maximum Means, measured current value is lower than scale.minimum

ERROR MESSAGES

When this key is pressed,

baudrate is seen.

SET

C.Inp 500

When this key is pressed,

measurement input type

s seen.

i “ ” .If nput type is selected, the measurement terminals 9 and 12 of the terminals must be connected Otherwise the measurement is done incorrectly.C.Inp 500

If ıC np 50input type “ ” is selected, the measurement terminals 10 and 11 of the terminals must be connected.Otherwise the measurement is done incorrectly.