Zennio MAXinBOX 66 Guide

MAXinBOX 66

MAXinBOX 66. Multi-function actuator 6 outputs 16A and 6 A/D inputs

ZN1IO-MB66 Technical Documentation

FEATURES

3 different configurable channels:

shutter channels (up to 3)

individual outputs (up to 6)

6 analog/digital inputs.

Manual output operation with push button and LED

status indicator.

Logical functions included.

Output timing facilities.

Total data saving on power failure.

Size 67 x 90 x 79 mm (4.5 DIN units).

DIN rail mounting (EN 50022), through pressure.

KNX BCU integrated.

Suitable for capacitive loads, maximum 140 µF.

Possibility to connect different phases in adjoining outputs.

Conformity with the CE directives (CE-mark on the right side).

Programming/test button: short press to set programming mode. If this button is held while plugging the device into the KNX bus, it enters the safe

mode. If this button is held for more than 3 seconds, the device enters the test mode.

Programming/Test LED: programming mode indicator (red). When the device enters into safe mode, it blinks (red) every half second. The manual

mode is indicated by the green color. During the start-up (reset or after KNX bus failure) and if the device is not in safe mode, it starts a blue blinking

sequence.

1. Analog/Digital inputs 2. Upper outputs 3. Output status LED indicator 4. Output control button

5. Programming/Test LED 6. Lower outputs 7. KNX connection 8. Programming/Test button

Figure 1. MAXinBOX 66

GENERAL SYSTEM SPECIFICATIONS

CONCEPT

DESCRIPTION

Type of device

Electric operation control device

KNX

supply

Voltage (typical)

29VDC SELV

Voltage range

21…31VDC

Maximum

consumption

Voltage

29VDC (typical)

203

24VDC

(1)

10 240

Bus connection

Typical TP1 bus connector for rigid cable 0.80mm Ø

External power supply

Operation temperature

from 0ºC to +55ºC

Storage temperature

from -20ºC to +70ºC

Operation humidity

5 to 95% RH (no condensation)

Storage humidity

5 to 95% RH (no condensation)

Complementary characteristics

Class B

Protection class

Operation type

Continuous operation

Device action type

Type 1

Electrical stress period

Long

Degree of protection

IP20, clean environment

Minimum clearances

Not required

Installation

Independent device to be mounted inside electrical panels with DIN rail (EN 50022).

Response on KNX bus failure Data saving and relay status change according to parameterization.

Response on KNX bus restart

Data recovering and output status change according to parameterization.

Operation indication

Programming LED indicates programming mode (red) and test mode (green). Output

status LED indicators reflect current output state.

Weight

264g

PCB CTI index

175V

Housing material

PC FR V0 halogen free

(1)

Maximum consumption in the worst case scenario (KNX Fan-In model)

Any combination of the next accessories is allowed in the inputs:

OUTPUTS SPECIFICATIONS AND CONNECTIONS

Contact type

Potential free outputs through bistable

relays with tungsten pre-contact.

Disconnection type

Micro-disconnection

Rated current by output

16A (6) * 250VAC (4000VA)

16A (6) * 30VDC (480W)

Maximum inrush current

800A/200μs (fluorescent lamps)

165A/20ms (resistive lamps)

Outputs per common (channel)

1 individual output

Different phases connection

Possibility to connect different phases in

adjoining outputs

Maximum power

Resistive load

4000W

Inductive load

1500VA

Maximum current

60A

Connection type

Screw terminal block

Recommended cable section

0.5mm² to 4mm² (26-10 AWG)

Cable type

Stranded or solid wire

Maximum response time

50ms

Expected life

Mechanical (min)

3 million operations (60cpm)

Electrical (min.)

100.000 cycles at maximum current

(6cpm and resistive load)

INPUT SPECIFICATIONS AND CONNECTIONS

CONCEPT

DESCRIPTION

Number of inputs per common

Input voltage

+3.3VDC for the common

Input current

1.0mA @ 3.3VDC (each input)

Input impedance

Aprox. 3.3kΩ

Switching type

Dry voltage contacts between

input and common

Connection method

Screw terminal block

Max. cable length

30m

NTC probe length

1.5m

NTC accuracy (@ 25ºC)

0.5ºC

Temperature measure precision

0.1ºC

Cable cross-section

0.5mm² to 2.5mm² (26-12 AWG)

Maximum response time

10ms

Attaching MAXinBOX 66 to DIN rail:

Removing MAXinBOX 66 from DIN rail:

Figure 2: (From up to down and

from left to right) Terminal block 1

wiring examples for shutter channel,

outputs with same phase or outputs

with different phases.

Zennio

Temperature

Probe

Up to two motion sensors

can be plugged into the

same MAXinBOX 66 input

(parallel wiring)

Motion sensor screw

terminal.

Motion sensor references:

ZN1IO-DETEC-P(2)

ZN1IO-DETEC-X

Temperature Probe

Motion Sensor

Switch/Sensor/

Push button

WIRING AND ASSEMBLY DIAGRAMS

(2) The micro switch number 2 in the ZN1IO-DETEC-P sensor must be in Type B position to work properly.

SAFETY INSTRUCTIONS

•Installation should only be performed by qualified professionals according to the laws and regulations applicable in each country.

•Do not connect the mains voltage nor any other external voltage to any point of the KNX bus; it would represent a risk for the entire

KNX system. The facility must have enough insulation between the mains (or auxiliary) voltage and the KNX bus or the wires of

other accessories, in case of being installed.

•Once the device is installed (in the panel or box), it must not be accessible from outside.

•Keep the device away from water and do not cover it with clothes, paper or any other material while in use.

•The WEEE logo means that this device contains electronic parts and it must be properly disposed of by following the instructions at

http://zennio.com/weee-regulation.

⚠

In order to ensure the expected status of the relays, please check that the device

is connected to the KNX bus before energizing the power circuit.

Other manuals for MAXinBOX 66

This manual suits for next models

Table of contents

Other Zennio Controllers manuals

Zennio

Zennio MAXinBOX FC 0-10V FAN User manual

Zennio

Zennio MAXinBOX 16 Plus Guide

Zennio

Zennio MAXinBOX 66 User manual

Zennio

Zennio MAXinBOX 8 v3 Guide

Zennio

Zennio MAXinBOX Hospitality ZCL-HP126 User manual

Zennio

Zennio ZCL-MCC User manual

Zennio

Zennio AudioInRoom ZMU-AUIR User manual

Zennio

Zennio Roll-ZAS User manual

Zennio

Zennio IDAC User manual

Zennio

Zennio ACTinBOX MAX6 User manual

Zennio

Zennio inBOX 24 v2 User manual

Zennio

Zennio inBOX 24 vT User manual

Zennio

Zennio MAXinBOX FC 0-10V VALVE User manual

Zennio

Zennio ZN1VI-TPZAS User manual

Zennio

Zennio MAXinBOX User manual

Zennio

Zennio MAXinBOX SHUTTER 8CH v3 Guide

Zennio

Zennio DIMinBOX 2CH ZDI-DB2C User manual

Zennio

Zennio ZoningBOX 6 Guide

Zennio

Zennio MAXinBOX 8 Guide

Zennio

Zennio MAXinBOX FC 0-10V FAN Guide

Zennio

Zennio ZoningBOX 6 Guide

Zennio

Zennio AudioInRoom User manual

Zennio

Zennio MAXinBOX 24 Guide

Zennio

Zennio MAXinBOX FC 0-10V VALVE User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual