Zennio HeatingBOX 230V 4X Guide

HeatingBOX 230V 4X

Heating actuator for up to 4 outputs 230VAC

ZCL-4HT230 TECHNICAL DOCUMENTATION

FEATURES

•4 configurable outputs for 230VAC valve control.

•4 thermostats.

•10 logic functions.

•Total data saving on KNX bus failure.

•Manual control through buttons and status LED indicators.

•Common 230VAC supply required for the 4 outputs.

•Integrated KNX BCU.

•Dimensions 67 x 90 x 35mm (2 DIN units).

•DIN rail mounting (EN 50022), through pressure.

•Conformity with the CE directives (CE-mark on the right side).

1. 230V input (live phase)

2. Valve outputs

3. Output control button

4. Output status Indicator LED

5. Programming/Test LED

6. Programming/Test button

7. KNX connector

Figure 1: HeatingBOX 230V 4X

Programming/test button: short press to set programming mode. If this button is held while plugging the device into the KNX bus, it enters the safe

mode. If this button is held for more than 3 seconds, the device enters the test mode.

Programming/Test LED: programming mode indicator (red). When the device enters the safe mode, it blinks (red) every half second. The manual mode

is indicated by the green color. During the start-up (reset or after KNX bus failure) and if the device is not in safe mode, it emits a red flash.

GENERAL SPECIFICATIONS

CONCEPT

DESCRIPTION

Type of device

Electric operation control device

KNX supply

Voltage (typical)

29VDC SELV

Voltage range

21..31VDC

Maximum

consumption

Voltage

29VDC (typical)

7.5

217.5

24VDC¹

240

Connection type

Typical TP1 bus connector for 0.80mm Ø rigid cable

External power supply

230V 50/60Hz (only phase, for valve supply)

Operation temperature

0°C .. +55°C

Storage temperature

-20°C .. +55°C

Operation humidity

5 .. 95% (No condens.)

Storage humidity

5 .. 95% (No condens.)

Complementary characteristics

Class B

Protection class

Operation type

Continuous operation

Device action type

Type 1

Electrical stress period

Long

Degree of protection

IP20, clean environment

Installation

Independent device to be mounted inside electrical panels with DIN rail (EN

50022)

Minimum clearances

Not required

Response on KNX bus failure

Data saving according to parameterization

Response on KNX bus restart

Data recovery according to parameterization

Operation indicator

The programming LED indicates programming mode (red) and test mode

(green). Each output LED indicates its status (fixed=active output;

flashing=overload or short-circuit). The blue blinking of the programming

LED indicates a 3 minutes lock due to the suffering of 3 short-circuits in less

than 3 minutes.

Weight

98g

PCB CTI index

175V

Housing material

PC FR V0 halogen free

¹ Maximum consumption in the worst case scenario (KNX Fan-In model)

SAFETY INSTRUCTIONS

•Installation should only be performed by qualified professionals according to the laws and regulations applicable in each country.

•Do not connect the mains voltage nor any other external voltage to any point of the KNX bus; it would represent a risk for the entire

KNX system. The facility must have enough insulation between the mains (or auxiliary) voltage and the KNX bus or the wires of other

accessories, in case of being installed.

•The facility must be equipped with a device that ensures the omnipolar sectioning. Installation of a 10A mini-circuit-breaker is

recommended. To prevent accidents, it must remain open in case of manipulation of the device.

•Once the device is installed (in the panel or box), it must not be accessible from outside.

•Keep the device away from water and do not cover it with clothes, paper or any other material while in use.

•The WEEE logo means that this device contains electronic parts and it must be properly disposed of by following the instructions at

http://zennio.com/weee-regulation.

OUTPUTS SPECIFICATIONS AND CONNECTIONS

CONCEPT

DESCRIPTION

Number of outputs

Output type

Solid state switching device

Maximum

recommended load per

output (AC/DC)

Quantity of valves ²

Stationary current

200mA (@ 35°C)

Maximum inrush current

2.5A

Short-circuit protection

YES

Overload protection

YES

Connection method

Screw terminal block

Cable cross-section

0.5-4mm² (IEC) / 26-12AWG (UL)

² This value could be more restrictive depending on the valve stationary current and inrush current.

EXTERNAL POWER SUPPLY SPECIFICATIONS AND CONNECTIONS

CONCEPT

DESCRIPTION

Voltage

230VAC 50/60Hz

Connection method

Screw terminal block

Cable cross-section

0.5-4mm² (IEC) / 26-12AWG (UL)

Connecting more than one valve to each output is allowed as long as the maximum current per output is not exceeded:

WIRINGDIAGRAMS

230VAC

50/60Hz

Valve 1

Valve n

(n≤5)

Valve

Figure 2: Wiring example: several valves per output and one valve per

output.

Figure 3: Mounting HeatingBOX 230V 4X on

DIN rail

Attaching HeatingBOX 230V 4X to DIN rail:

Removing HeatingBOX 230V 4X from DIN rail:

•NOTE: Simultaneous connection of one

valve to several outputs is not allowed.

Several valves per output

connection schematic

One valve per output

connection schematic

Other manuals for HeatingBOX 230V 4X

This manual suits for next models

Table of contents

Other Zennio Controllers manuals

Zennio

Zennio IRSC Zone User manual

Zennio

Zennio MAXinBOX 24 Guide

Zennio

Zennio MAXinBOX FC 0-10V VALVE User manual

Zennio

Zennio ZN1CL-IRSC User manual

Zennio

Zennio inBOX 24 vT User manual

Zennio

Zennio Tecla 55 X Sign User manual

Zennio

Zennio DIMinBOX 2CH ZDI-DB2C User manual

Zennio

Zennio MAXinBOX FANCOIL 2CH2P User manual

Zennio

Zennio ZIO-IB24 User manual

Zennio

Zennio MAXinBOX FC 0-10V FAN Guide

Zennio

Zennio MINiBOX 40 v3 User manual

Zennio

Zennio ZCL-8HT230 Guide

Zennio

Zennio ZCL-FC010F Guide

Zennio

Zennio MAXinBOX FANCOIL 4CH2P Guide

Zennio

Zennio MAXinBOX FC 0-10V FAN User manual

Zennio

Zennio AudioInRoom ZMU-AUIR User manual

Zennio

Zennio MAXinBOX 16 Plus Guide

Zennio

Zennio Tecla 55 User manual

Zennio

Zennio ZCL-MCC User manual

Zennio

Zennio MAXinBOX 8 v3 Guide

Zennio

Zennio IDAC User manual

Zennio

Zennio MAXinBOX FC 0-10V FAN Guide

Zennio

Zennio FANinBOX 230V 1CH Guide

Zennio

Zennio MAXinBOX 66 Guide

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual