Zennio MAXinBOX 24 Guide

MAXinBOX 24

Multifunction actuator with 24 (16A) outputs

ZIO-MB24 Technical Documentation

FEATURES

▪6 configurable blocks:

oShutter channels (up to 12).

oIndividual outputs (up to 24).

o2-pipe fan coil control (up to 6 fan coils).

▪Manual output operation with push button and LED status indicator.

▪Suitable for capacitive loads, maximum 140 μF.

▪Possibility of connecting different phases in adjoining outputs.

▪30 logic functions.

▪Total data saving on KNX bus failure.

▪Integrated KNX BCU.

▪Dimensions 69 x 96 x 210mm (12 DIN units).

▪DIN rail mounting (EN 50022), through pressure.

▪Conformity with the CE directives (CE-mark on the right side).

Programming/test button: short press to set programming mode. If this button is held while plugging the device into the KNX bus, it enters the safe

mode. If this button is held for more than 3 seconds, the device enters the test mode.

Programming/Test LED: programming mode indicator (red). When the device enters the safe mode, it blinks (red) every half second. The manual

mode is indicated by the green color. During the start-up (reset or after KNX bus failure) and if the device is not in safe mode, it starts a blue blinking

sequence.

1. Output

2. Output status LED

3. Output control button

4. Fixing clamp

5. Programming/Test button

6. Programming/Test LED

7. KNX connector

Figure 1. MAXinBOX 24

GENERAL SPECIFICATIONS

CONCEPT

DESCRIPTION

Type of device

Electric operation control device

KNX

supply

Voltage (typical)

29VDC SELV

Voltage range

21…31VDC

Maximum

consumption

Voltage

29VDC (typical)

3.92

113.68

24VDC(1)

240

Connection type

Typical bus connector TP1 for 0.80mm Ø rigid cable

External power supply

Not required

Operation temperature

0ºC to +45ºC

Storage temperature

-20ºC to +55ºC

Operation humidity

5 to 95% RH (no condensation)

Storage humidity

5 to 95% RH (no condensation)

Complementary characteristics

Class B

Protection class

Operation type

Continuous operation

Device action type

Type 1

Electrical stress period

Long

Degree of protection

IP20, clean environment

Installation

Independent device to be mounted inside electrical panels with DIN rail (EN 50022)

Minimum clearances

Not required

Response on KNX bus failure

Data saving according to parameterization

Response on KNX bus restart

Data recovery according to parameterization

Operation indicator

The programming LED indicates programming mode (red) and test mode (green).

Each output LED indicates its status (green)

Weight

700g

PCB CTI index

175V

Housing material

PC FR V0 halogen free

(1) Maximum consumption in the worst case scenario (KNX Fan-In model)

SAFETY INSTRUCTIONS

•Installation should only be performed by qualified professionals according to the laws and regulations applicable in each country.

•Do not connect the mains voltage nor any other external voltage to any point of the KNX bus; it would represent a risk for the entire

KNX system. The facility must have enough insulation between the mains (or auxiliary) voltage and the KNX bus or the wires of other

accessories, in case of being installed.

•Once the device is installed (in the panel or box), it must not be accessible from outside.

•Keep the device away from water and do not cover it with clothes, paper or any other material while in use.

•The WEEE logo means that this device contains electronic parts and it must be properly disposed of by following the instructions at

http://zennio.com/weee-regulation.

Removing MAXinBOX 24 from DIN rail:

Attaching MAXinBOX 24 to DIN rail:

Figure 3. Mounting MAXinBOX 24

on a DIN rail

OUTPUTS SPECIFICATIONS AND CONNECTIONS

CONCEPT

DESCRIPTION

Contact type

Potential-free outputs through bistable relays with tungsten pre-contact.

Disconnection type

Micro-disconnection

Rated current per output

16(6)A * 250VAC (4000VA) 16(6)A * 30VDC (480W)

Maximum power

per output

Resistive

4000W

Inductive

1500W

Maximum inrush current

800A/200μs (fluorescent lamps)

165A/20ms (resistive lamps)

Number of outputs

24 outputs

Outputs per common (Channel)

1 individual output

Different phases connection

Possibility to connect different phases in adjoining outputs

Total maximum current in device

40A per block

Connection type

Screw terminal block

Recommended cable section

0.5mm² to 4mm² (26-10 AWG)

Maximum response time

50ms

Lifetime

Mechanical (min)

3 million cycles (60cpm)

Electrical (min.)

100.000 cycles at max. current (6cpm and resistive load)

WIRING AND ASSEMBLY DIAGRAMS

Figure 2. Wiring examples (from left to right): individual outputs in channel A with the same and different phases, channel A as

shutter channel, and channel A and B as fan coil controller (2 pipe and three-speed fan).

⚠In order to ensure the

expected status of the relays,

please check that the device is

connected to the KNX bus

before energizing the power

circuit.

This manual suits for next models

Table of contents

Other Zennio Controllers manuals

Zennio

Zennio Tecla 55 User manual

Zennio

Zennio MAXinBOX FC 0-10V VALVE User manual

Zennio

Zennio Roll-ZAS User manual

Zennio

Zennio MINiBOX 25v2 User manual

Zennio

Zennio HeatingBOX 230V 4X Guide

Zennio

Zennio MAXinBOX 8 v3 Guide

Zennio

Zennio FANinBOX 230V 1CH Guide

Zennio

Zennio LUMENTO X4 Guide

Zennio

Zennio MAXinBOX SHUTTER 4CH User manual

Zennio

Zennio MINiBOX 45 v3 Guide

Zennio

Zennio Tecla 55 X Sign User manual

Zennio

Zennio MINiBOX 45v2 User manual

Zennio

Zennio MAXinBOX 66 v2 Guide

Zennio

Zennio ZoningBOX 6 Guide

Zennio

Zennio MAXinBOX SHUTTER 8CH v3 Guide

Zennio

Zennio MINiBOX 25 v3 Guide

Zennio

Zennio ZCL-MCC User manual

Zennio

Zennio MINiBOX 40 v3 User manual

Zennio

Zennio MAXinBOX User manual

Zennio

Zennio ZoningBOX 6 Guide

Zennio

Zennio ALLinBOX 1612 v2 User manual

Zennio

Zennio IRSC Zone User manual

Zennio

Zennio inBOX 24 vT User manual

Zennio

Zennio MAXinBOX 8 Plus Guide

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual