Zennio Roll-ZAS User manual

Roll-ZAS

KNX Room Controller

ZN1VI-TPZAS

Program: version 1.1

Manual: edition a

PRODUCT MANUAL

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

INDEX

Document updates ............................................................................................................................................... 3

1. Introduction.................................................................................................................................................. 4

1.1. ZAS........................................................................................................................................................ 4

1.2. Installation............................................................................................................................................ 5

2. Configuration ................................................................................................................................................ 8

2.1. Roll-ZAS application.............................................................................................................................. 8

2.2. Touch Area............................................................................................................................................ 9

2.3. Page navigation .................................................................................................................................. 10

2.4. ZAS IR control ..................................................................................................................................... 12

3. ETS Parameterization.................................................................................................................................. 14

3.1. Default configuration ......................................................................................................................... 14

3.2. General ............................................................................................................................................... 15

3.3. Pages................................................................................................................................................... 21

3.3.1. Pages 1-4 .................................................................................................................................... 23

a) Pair buttons ............................................................................................................................................ 24

b) Individual buttons .................................................................................................................................. 28

3.3.2. Configuration page ..................................................................................................................... 30

3.3.3. Security page .............................................................................................................................. 32

3.3.4. Indicators page ........................................................................................................................... 34

3.3.5. Screensaver ................................................................................................................................ 35

3.4. Inputs.................................................................................................................................................. 36

3.4.1. Switch/Sensor............................................................................................................................. 36

3.4.2. Temperature probe .................................................................................................................... 37

3.4.3. Movement detector ................................................................................................................... 38

3.5. Thermostats........................................................................................................................................ 39

3.6. Presence simulation ........................................................................................................................... 40

Annex I. Button icons.......................................................................................................................................... 42

Annex II. Communication objects....................................................................................................................... 43

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

DOCUMENT UPDATES

Version

Modifications

Page(s)

1.1a

Changes since version 1.0 of the application program:

Use of the central area of the touch panel as a binary control.

Introduction: brief explanation about the new functionality in the “Roll-

ZAS” application program.

Changes in the factory defaults. Possibility to enter the programming mode

from the buttons of the touch panel.

Section 2.4: note added on the use of the remote control.

Section 3.3: screenshot updated; information added about using the

central area of the touch panel as a binary control.

22,23

Section 3.3.5: information added about parameter “Execute Page 1 actions

at screensaver exit?”.

Annex II: object 246 “[General] Central Button” added.

General improvement of this English version of the manual –texts and

minor issues.

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

1. INTRODUCTION

1.1. ZAS

Room controller ZAS (Zennio Analogue Screen) is a touch panel that includes a thermostat,

an IR receiver, and analogue/binary inputs. ZAS is a smart solution for demanding applications in

hotel rooms, apartments, offices, and in any other environment where it is necessary to control

climate, shutters, lights, scenes, etc.

Figure 1.1. ZAS Room Controller

The most relevant features of ZAS are shown below.

1.8" back-lighted display with 128 x 64 pixels

Temperature sensor with thermostat function

12 touch buttons

Screensaver showing current time and temperature (internally measured by ZAS or by an

external device), with a letter size suitable for being read from several meters away

Two opto-coupled inputs, configurable as switches/sensors, temperature sensors or

movement detectors.

Two different downloadable application programs to choose from:

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

ZAS: this application puts together all the functionality of the controller within a Menu,

which is divided into several submenus (Thermostat, Security, Scenes, etc.). It is possible

to configure the functionality of up to 8 buttons in total, which will carry out different

actions, according to the ETS configuration. Button actions do not vary while navigating

though the Menu. Moreover, every action over them is confirmed with an easily readable

pop-up. The whole functionality of this application can be checked in the corresponding

user manual, available at http://www.zennio.com.

Roll-ZAS: a more versatile application with an intuitive user interface and with a high

degree of usability, functionality and capacity. Information is divided into pages (up to a

total of 4 direct-action button pages, besides specific pages as Security, Configuration,

etc.). For every button page it is possible to configure up to 8 buttons, which will carry out

different actions, according to the ETS configuration. Moreover, starting with version 1.1,

it is also possible to use the central area of the touch panel as an additional binary

control, providing the user with a quick manner of, for example, turning a light source on

or off whenever it is required.

1.2. INSTALLATION

ZAS is connected to the KNX installation as any other KNX device, through the KNX

connector located at the back.

For installing ZAS, it is first necessary to fix the metallic piece into the squared/rounded standard

box where it is going to be installed, with the corresponding screws.

Next, the KNX bus and the input terminal must be connected using the corresponding connectors;

both terminals are located in the rear part of the device.

Once the inputs and the KNX bus are connected, the device is fitted into the metal platform with the

help of the included magnets.

Finally, it is necessary to check, from both sides, that nothing unless the ZAS outline can be seen

(the metal platform should be completely hidden by ZAS).

This device does not need any additional external power supply since it is powered through the

KNX bus.

In figure 1.2, the element outline of ZAS is shown.

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

Figure 1.2. ZAS Element scheme

The programming button (3) is used to set ZAS into the programming mode, by means of a short

push (the programming LED lights in red).

Note: If this button is held while plugging the device into the KNX bus, ZAS will go into secure

mode. The LED blinks in red.

Apart from the programming button(3), and particularly when it turns to be inaccessible, it will be

possible to enter the programming mode from the touch interface itself. In the factory default state,

after being connected to the KNX bus and prior to any type of download, the device will show a

certain interface, with almost no functionality at all, which, however, will commute between pages

“1” and “C” (Configuration) by pressing the “Menu” button (upper left button). Under page “C”,

pressing button number 5 (labelled with the text “Prog. LED” in the screen) will be totally equivalent

to pressing the programming button (3).

Figura 1.3. Screens “1” and “C” in the factory state

1.-KNX connector

2.- Temperature sensor

3.- Programming button

4.- Programming LED

5.- Inputs (A/D)

6 - Magnet

7.- Touch box

8 - Display

9.- IR receiver

10. Central touch panel area

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

Once the download of the application program finishes, it is necessary to calibrate ZAS. The touch

calibration is carried out pressing buttons 1, 2, 7 and 8, in this order (the sequence is shown in

Figure 1.3). The Display screen will indicate the button to be pressed each time (only if a text string

associated to this process has been previously configured in ETS, under "General Labels". See

section 3.2).

Figure 1.3. Calibration sequence

To obtain more detailed information about the technical features of ZAS, as well as security and

installation information, please read the controller Datasheet, included in the original package of the

device and also available at: http://www.zennio.com.

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

2. CONFIGURATION

2.1. ROLL-ZAS APPLICATION

The Roll-ZAS application allows controlling a series of functionalities in a domotic installation

in a simple and intuitive way.

There are several parameters that refer to the general functionality of the controller, such as:

luminosity, touch panel locking, initial update, internal sensor, contrast, buzzer sound, presence

simulation, etc.

Pages

The information shown in the Display is divided into pages. It is possible to enable and

configure up to a total of 4different button pages (Page 1-4), as well as the specific pages

Configuration, Security, Indicators and Screensaver. All of them are explained in detail in

section 3.3 Pages of this manual.

The access and navigation through the configured pages is explained in section 2.3.

Inputs

ZAS incorporates 2 opto-coupled inputs each of which may be individually configured as a

switch/sensor, atemperature probe or a movement detector. Depending on the selected

configuration, it is necessary to connect different external elements to the ZAS inputs: push

buttons or switches, temperature probes (like Zennio ZN1AC-NTC68) or movement sensors

(Zennio ZN1IO-DETECT).

Thermostats

ZAS allows enabling and configuring in an independent manner up to 2 thermostats, with the

"Building" functionality. How they work and the ETS configuration of this kind of thermostat is

detailed in the specific documentation "Zennio Building Thermostat", available at:

http://www.zennio.com.

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

2.2. TOUCH AREA

ZAS incorporates 12 touch buttons for controlling all its functionality. Moreover, this is

complemented by the central area of the touch panel, which can also be used as a binary control.

See figure 2.1.

Figure 2.1. Touch Area

The first row of the touch panel consists of the following buttons:

Menu button: to navigate through the different pages of ZAS (only if this option is enabled

by parameter; see section 3.3).

Arrow buttons: to navigate through the different pages of ZAS (only if this option is

enabled by parameter; see section 3.3). Moreover, with the arrow buttons it is possible to

increase/decrease, one by one, the values of contrast, illumination and time of the Display

from the Configuration page, as well as establishing times for the timers (in the case of the

buttons configured with such purpose; see section 3.3.1).

OK Button: button to confirm and to select the desired option.

Under this first row, there are 8 more buttons, distributed into 4 rows of two buttons each. They can

be configured through ETS to operate either independently or in pairs, implementing joint functions.

They are direct-action buttons, i.e., they will carry out the parameterized action every time they are

pressed. The executed action will depend on the parameterization for the buttons in every enabled

page.

Touch Area

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

Each button contains a central LED that lights on during the time the button is kept pressed, thus

making it clear that the key press has been detected. The illumination status of the LED can be

customized, choosing between a normal illumination or dependant on the associated

communication object status. (See section 3.3.1 for further information). No LED will on in the case

of the central binary control of the touch panel.

ZAS will emit a soft beep every time a control in the touch area is pressed, unless the buzzer has

been disabled through the corresponding object.

2.3. PAGE NAVIGATION

The Roll-ZAS application has an intuitive user interface that allows, through the use of

pages, knowing at any time the chosen functionality for every button of a page.

Figure 2.2 shows how the pages are represented in the Display.

Figure 2.2. Example of page representation in the Display

Header

In the left side of the header a name (configured by parameter. See section 3.3.1) will be

shown, which identifies the current page (“ROOM 2”, in the above sample picture).

In the right side a navigation scheme is shown, composed by the sequence of numbers and

letters "i 1234 C S":

"i" refers to the Indicators page.

"1 2 3 4" refer to the pages where the direct-action controls are.

"C" refers to the Configuration page.

"S" refers to the Security page.

Header

Buttons

Other manuals for Roll-ZAS

This manual suits for next models

Table of contents

Other Zennio Controllers manuals

Zennio

Zennio MINiBOX 25 v3 Guide

Zennio

Zennio IRSC Plus User manual

Zennio

Zennio MAXinBOX66 Guide

Zennio

Zennio MAXinBOX 66 v2 Guide

Zennio

Zennio LUMENTO X4 Guide

Zennio

Zennio MAXinBOX FC 0-10V VALVE User manual

Zennio

Zennio MAXinBOX FC 0-10V VALVE User manual

Zennio

Zennio MINiBOX 45v2 User manual

Zennio

Zennio ZCL-8HT230 User manual

Zennio

Zennio ZN1VI-TPZAS User manual

Zennio

Zennio ZCL-FC010F Guide

Zennio

Zennio Tecla 55 User manual

Zennio

Zennio MAXinBOX 16 Guide

Zennio

Zennio MAXinBOX SHUTTER 4CH User manual

Zennio

Zennio Roll-ZAS User manual

Zennio

Zennio HeatingBOX 24V 4X User manual

Zennio

Zennio MAXinBOX FC 0-10V FAN User manual

Zennio

Zennio DIMinBOX 2CH ZDI-DB2C User manual

Zennio

Zennio MAXinBOX SHUTTER 8CH v3 Guide

Zennio

Zennio AudioInRoom User manual

Zennio

Zennio MAXinBOX User manual

Zennio

Zennio ZoningBOX 6 Guide

Zennio

Zennio IDAC User manual

Zennio

Zennio MAXinBOX 8 Guide

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual