Zennio MAXinBOX 8 v3 Guide

MAXinBOX 8 v3

Multifunction actuator with 8 outputs (16 A)

ZIOMB8V3 TECHNICAL DOCUMENTATION

FEATURES

•2 different configurable blocks: shutter channels (up to 4), individual

outputs (up to 8) and 2-pipe fan coil control (up to 2)

•Outputs suitable for capacitive loads, maximum 140 µF

•Manual output operation with push button and LED status indicator

•20 logic functions

•Output timing

•Total data saving on KNX bus failure

•Integrated KNX BCU (TP1-256)

•Dimensions 67 x 90 x 79 mm (4.5 DIN units)

•DIN rail mounting according to IEC 60715 TH35, with fixing clamp

•Possibility of connecting different phases in adjacent outputs

•Conformity with the CE, UKCA, RCM directives (marks on the right side)

1. Upper outputs

2. Lower outputs

3. Programming/test LED

4. KNX Connector

5. Fixing clamp

6. Programming/test button

7. Output control button

8. Output status LED indicator

Figure 1: MAXinBOX 8 v3

Programming/Test button: short press to set programming mode. If this button is held while plugging the device into the KNX bus, it enters the safe

mode. If this button is held for more than 3 seconds, the device enters the test mode.

Programming/Test LED: programming mode indicator (red). When the device enters the safe mode, it blinks (red) every half second. The manual mode

is indicated by the green color. During the start-up (reset or after KNX bus failure)and if the device is not in safe mode,it starts a blue blinkingsequence.

GENERAL SPECIFICATIONS

CONCEPT

DESCRIPTION

Type of device

Electric operation control device

KNX supply

Voltage (typical)

29 VDC SELV

Voltage range

21-31 VDC

Maximum

consumption

Voltage

29 VDC (typical)

116

24 VDC¹

240

Connection type

Typical TP1 bus connector for 0.8 mm Ø rigid cable

External power supply

Not required

Operation temperature

0 .. +55 °C

Storage temperature

-20 .. +55 °C

Operation humidity

5 .. 95%

Storage humidity

5 .. 95%

Complementary characteristics

Class B

Protection class / Overvoltage category

II / III (4000 V)

Operation type

Continuous operation

Device action type

Type 1

Electrical stress period

Long

Degree of protection / Pollution degree

IP20 / 2 (clean environment)

Installation

Independentdevice to be mounted inside electricalpanels with DIN rail (IEC

60715)

Minimum clearances

Not required

Response on KNX bus failure

Data saving according to parameterization

Response on KNX bus restart

Data recovery according to parameterization

Operation indicator

The programming LED indicates programming mode (red) and test mode

(green). Each output LED indicates its status

Weight

188 g

PCB CTI index

175 V

Housing material / Ball pressure test temperature

PC FR V0 halogen free / 75 °C (housing) - 125 °C (connectors)

¹ Maximum consumption in the worst-case scenario (KNX Fan-In model).

SAFETY INSTRUCTIONS ANDADDITIONAL NOTES

•Installation should only be performed by qualified professionals according to the laws and regulations applicable in each country.

•Do not connect the mains voltage nor any other external voltage to any point of the KNX bus; it would represent a risk for the entire

KNX system. The facility must have enough insulation between the mains (or auxiliary) voltage and the KNX bus or the wires of other

accessories, in case of being installed.

•Once the device is installed (in the panel or box), it must not be accessible from outside.

•Keep the device away from water (condensation over the device included) and do not cover it with clothes, paper or any other material

while in use.

•The WEEE logo means that this device contains electronic parts and it must be properly disposed of by following the instructions at

https://www.zennio.com/en/legal/weee-regulation.

•This device contains software subject to specific licences. For details, please refer to http://zennio.com/licenses.

OUTPUTS SPECIFICATIONS AND CONNECTIONS

CONCEPT

DESCRIPTION

Number of outputs

Output type / Disconnection type

Potential-free outputs through bistable relays with tungsten pre-contact /

Micro-disconnection

Rated current per output

AC 16(6) A @ 250 VAC (4000 VA)

DC 7 A @ 30 VDC (210 W)

Maximum load per output

Resistive

4000 W

Inductive

1500 VA

Maximum inrush current

800 A/200 μs

165 A/20 ms

Connections in adjacent outputs

Possibility of connecting different phases. It is not allowed to connect power

supplies of different order, SELV with NO SELV, in the same block

Total maximum current in device

80 A

Short-circuit protection

Overload protection

Connection method

Screw terminal block (0.5 Nm max.)

Cable cross-section

1.5-4 mm² (IEC) / 26-10 AWG (UL)

Outputs per common

Maximum response time

10 ms

Mechanical lifetime (min. cycles)

3 000 000

Electrical lifetime (min. cycles)1

100000 @ 8 A / 25000 @ 16 A (VAC)

¹ Lifetime values could change depending on the load type.

⚠In order to ensure the expected status

of the relays, please check that the

device is connected to the KNX bus

before energizing the power circuit.

WIRINGDIAGRAMS

Figure 2: Wiring example (from left to right): 2 loads, 2 loads

connected to different phases, shutter and fan coil

Attaching MAXinBOX 8 v3 to DIN rail:

Removing MAXinBOX 8 v3 from DIN rail:

Figure 3: Mounting MAXinBOX 8 v3 on DIN rail

This manual suits for next models

Table of contents

Other Zennio Controllers manuals

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual