Univex ALMFC12 User manual

OPERATORS

MANUAL

ALMFC12

ALMFC12/09 ED 1

MEAT & FOOD

CHOPPER

TO INSURE BOTH SAFE AND TROUBLE-FREE PERFORMANCE WE

STRESS THAT ALL PERSONNEL THAT WILL BE INVOLVED WITH

YOUR NEW UNIVEX MEAT AND FOOD CHOPPER MUST READ

AND UNDERSTAND THESE INSTRUCTIONS BEFORE ATTEMPTING

TO OPERATE THIS UNIT.

•••••••••••••••••••••••••••••••••••••••

WE APPRECIATE YOUR COOPERATION AND YOUR BUSINESS.

SHOULD THERE BE A UESTION OR IF WE CAN BE OF FURTHER

ASSISTANCE, PLEASE CALL US.

1-603-893-6191

INTRODUCTION

Please read the following instructions carefully before assembling the ALMFC12 Meat and Food

Chopper. This instruction manual contains vital information concerning inspection, safe operation and

cleaning of the unit.

INSPECTION

The FLMFC12 Meat and Food Chopper has been inspected and tested at the factory, however, the user

should inspect the unit and compare the parts received with the parts list on page 4 prior to use. Any

damage should be reported to the carrier immediately and any shortage or deviation of parts should be

reported to Univex Corporation.

INSTALLATION

Before attempting to mount the ALMFC12 Meat and Food Chopper to the power source equipment for

processing, be sure all equipment is located to save the operator steps and that sufficient clearance is

provided all around for safety and ease of operation.

SAFETY

The Univex ALMFC12 Meat and Food Chopper is supplied with a feed pan and a feed stomper.

Product to be processed should always be inserted into the chopper housing throat by way of the pan and

pressed into the worm with the stomper. NEVER ATTEMPT TO FEED PRODUCT WITH YOUR

FINGERS OR USE ANY UTENSILS OTHER THAN THE STOMPER TO PUSH PRODUCT

INTO THE CHOPPER

NEVER PUT FINGERS OR OBJECTS INTO THE HOLES IN THE PLATES

TO AVOID ACCIDENTAL START-UPS, DISCONNECT THE ELECTRICAL POWER TO THE

POWER SOURCE E UIPMENT BEFORE MOUNTING OR DISMOUNTING THE ALMFC12

MEAT AND FOOD CHOPPER.

ALL POWER SOURCE E UIPMENT IS PROVIDED WITH A THUMB SCREW ON THE POWER

TAKE-OFF HOUSING. MAKE SURE THIS THUMB SCREW IS FIRMLY TIGHTENED BEFORE

OPERATING THE MEAT AND FOOD CHOPPER.

ALWAYS REMOVE THE MEAT AND FOOD CHOPPER FROM THE POWER SOURCE

E UIPMENT BEFORE CLEANING. NEVER ATTEMPT TO WASH OR RINSE THE MEAT AND

FOOD CHOPPER WITH A HOSE IF THE MEAT AND FOOD CHOPPER IS MOUNTED TO THE

POWER SOURCE E UIPMENT. HOSING A MOUNTED MEAT AND FOOD CHOPPER INVITES

ELECTRICAL SHOCK.

IT IS A VIOLATION OF UNITED STATES DEPARTMENT OF LABOR REGULATIONS TO

PERMIT OPERATION OF THIS UNIT BY ANY PERSON UNDER THE AGE OF 18 YEARS.

Page 1

ASSEMBLY AND LUBRICATION

Before assembling the ALMFC12 Meat and Food Chopper wash all components thoroughly according

to the cleaning instructions below. Lubricate the drive shaft and the fiber washer with a light coat of

sanitary Petrol-Gel. Do not lubricate with cooking oil; it becomes gummy. Lubricate the knife and the

plate with a light coat of beef tallow.

To assemble the ALMFC12 Meat and Food Chopper:

• Coat the knife and plate with Petrol-Gel.

• Place the knife, sharp edges facing out, on the square extension of the worm assembly.

• Place the plate on the pin in the end of the worm and into the chopper housing aligning the

notch in the plate with the pin in the chopper housing.

• Screw the ring onto the chopper housing using minimum force. The ring controls the pressure

between the knife and the plate. Too much pressure will damage the knife and the plate.

Adjusting the ring will not change the consistency of the product, consistency is determined

by the plate you use.

Do not run the ALMFC12 Meat and Food Chopper unless it is processing product. The knife and plate

are easily ruined by running dry.

MOUNTING

DISCONNECT THE ELECTRICAL POWER TO THE POWER SOURCE EQUIPMENT

BEFORE MOUNTING THE ALMFC12 MEAT AND FOOD CHOPPER

To mount the ALMFC12 Meat and Food Chopper slide the chopper assembly, without the pan and

stomper, into the power take-off hub of the power source equipment. Align the pin in the chopper

housing with the hole in the power take-off hub and slide the chopper assembly all the way into the hub.

Make sure there is a firm fit between the drive shaft and the mating power take-off adapter provided

with the power source equipment. Tighten the thumb screw on the power take-off hub. Fit the pan to the

chopper housing and connect the electrical power to the power source equipment.

Page 2

Worm

Fiber Washer

Drive Shaft

Apply Petrol-Gel to these

Surfaces Prior to Assembly

WORM ASSEMBLY

FIGURE 1

OPERATING THE ALMFC12 MEAT AND FOOD CHOPPER

• Slice meat into strips, not chunks, which will easily slip down the throat of the chopper housing.

• Place a suitable container at the discharge of the chopper.

• Place the meat in the feed pan and turn the power source equipment on.

• Hand feed the meat into the chopper. DO NOT place fingers inside the throat of the chopper, use

the stomper to push the meat into the worm.

• If the power source equipment is a food mixing machine, adjust the speed from “1” to a speed that

produces the best results.

• Do not use the stomper to force feed the meat into the chopper at an increased rate. Best results

are obtained when the meat is fed only as fast as the chopper processes it.

• Switch the power “OFF” when processing is interrupted. Do not run the chopper when it is not

processing product.

• When the processing has been completed, switch the power “OFF” and disconnect the power

supply cord.

CLEANING

For proper sanitation, dismount and wash the ALMFC12 Meat and Food Chopper immediately after use.

Disassemble the components and hand wash them in a warm water and mild soap solution. Handle the

knife carefully, IT IS SHARP AND CAN EASILY CUT FINGERS Dry the components with a soft

cloth. Store the unit in a refrigerator after cleaning for extra sanitation.

REPAIR

Problems with the ALMFC12 Meat and Food Chopper usually be traced to improper assembly,

mounting, dull, worn, or broken parts. Check for solutions in that order.

Page 3

Page 4

STOMPER

ALIGNMENT PIN

RING

PLATE

KNIFE

WORM ASSEMBLY

CHOPPER HOUSING

FEED PAN

ALMFC12 MEAT AND FOOD CHOPPER

FIGURE 2

Warranty

The Univex ALMFC Meat and Food Chopper carries a

six (6) month, on-site parts and labor warranty against

any defects in materials or workmanship. The six month

period begins on the date of purchase by the end user and

remains in full effect provided the unit is used properly

and in accordance with our instructions for six months.

Please call the Univex Warranty Service Department at

800-258-6358 to report warranty claims before arranging

repair of the unit. The unit must be delivered to Univex

authorized service agent or to the Univex facility for

warranty repairs. The end user is responsible for all travel

or shipping charges arising from the repair or servicing of

this unit under warranty. Any service or repair must take

place in the United States. Univex will not cover over-

time charges of any kind.

Damages incurred in transit or incurred because of

installation error, accident, alteration, or misuse are not

covered by this warranty. Transit damages should be

reported to the carrier immediately.

Univex will not be liable for any consequential,

compensatory, incidental or special damages.

TOLL FREE ORDERING FAX 1-800-356-5614

3 Old Rockingham Road, Salem, N.H. 03079-2140 Telephone -603-893-6191 Fax 1-603-893-1249

Table of contents

Other Univex Kitchen Appliance manuals

Popular Kitchen Appliance manuals by other brands

Tayama

Tayama TYG-35AF instruction manual

AEG

AEG 43172V-MN user manual

REBER

REBER Professional 40 Use and maintenance

North American

North American BB12482G / TR-F-04-B-NCT-1 Assembly and operating instructions

Presto

Presto fountain popper instruction manual

Westmark

Westmark 1035 2260 operating instructions

Zanussi

Zanussi ZCG64396XA user manual

HOFFEN

HOFFEN SM-9302M instruction manual

Philips

Philips HD3133 user manual

Ronco

Ronco Beef Jerky User guide and recipes

Hendi

Hendi 470411 user manual

Livoo

Livoo MEN386 user manual

Vogue

Vogue D446 instruction manual

croydon

croydon WR-10313-700 instruction manual

ADE

ADE AUTOMATIC-L operating instructions

Chefman

Chefman RJ43-SQ Series user guide

Vacmaster

Vacmaster VP680 user guide

Jetmaster

Jetmaster 900HG operating instructions