Sunbeam SCK02SMWBS User manual

PTT092106

User’s Manual

Beer Dispenser

Model: SCK02SMWBS

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS 3

GROUNDING INSTRUCTIONS 5

PRODUCT DIAGRAM 6

INSTALLATION INSTRUCTIONS 7

OPERATION INSTRUCTIONS 11

BEFORE CALLING FOR SERVICE 12

IMPORTANT SAFETY INSTRUCTIONS

READ ALL SAFETY INSTRUCTIONS BEFORE USING THIS APPLIANCE

When using electrical appliances, basic safety precautions should be followed, including the following:

Read all instructions before using the beer dispenser.

Plug into a grounded 3-prong outlet; do not remove grounding plug; do not use an adapter; do not

use an extension cord.

Replace all panels before operating.

It is recommended a separate circuit be used for this unit. Use outlets that cannot be turned on and

off with a switch or pull chain.

Never clean unit parts with ﬂammable ﬂuids. Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any other appliance. Fumes can create a ﬁre hazard or

explosion.

Before cleaning or doing any maintenance to the unit, ensure the power is turned off and the power

cord is disconnected from the power outlet.

Do not attempt to service the unit unless it is speciﬁcally recommended in this manual. All other

servicing should be referred to a qualiﬁed technician.

Use two or more people to move and install the unit. Failure to do so may result in back or other

injury.

To ensure proper ventilation, the front of the unit must be completely unobstructed. Choose a well-

ventilated area with temperatures between 60°F and 90°F.

Do not place this unit near heat sources.

This unit must be installed with all electrical, water, and drain connections in accordance with state

and local codes. A standard electrical supply properly grounded in accordance with the National

Electrical Code and local codes and ordinances is required.

Do not kink or pinch the power supply cord.

The fuse or circuit breaker should be 15 amperes.

It is important the unit be level in order for it to work properly. You may need to make several

adjustments.

All installation must be in accordance with local plumbing code requirements.

Make certain the pipes are not pinched, kinked, or damages during installation.

Check for leaks after connection.

Never allow children to operate, play with, or crawl inside the unit.

Do not use this unit for anything other than its intended purpose.

Before throwing away an old unit, remove the doors, but leave the shelves in place so that children

cannot easily climb inside.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

IMPORTANT SAFETY INSTRUCTIONS (continued)

CO2cylinders contain high-pressure compressed gas which can be hazardous if not handled properly.

Make sure to read this section and understand the following procedures:

Always connect the CO2cylinder to a regulator. Failure to do so may result in explosion with

possible death or injury when the cylinder valve is opened.

Never connect the CO2cylinder directly to the product container.

Always follow correct procedures when cylinders are changed.

Always secure the cylinder in an upright position.

Never drop or throw a CO2cylinder.

Always keep CO2cylinders away from heat. Store extra cylinders in a cool place. Securely fasten

with a chain in an upright position.

Always ventilate and leave the area immediately if CO2leakage has occurred.

Always check the D.O.T. test date on the cylinder neck before installation. If over ﬁve years old, do

not use; return cylinder to gas supplier.

Never connect a product container unless there are two safeties in the pressure system: one at or on

the CO2regulator and one at or on the product coupler on in the pressure gas line.

CO2GAS CAN BE DANGEROUS

INSTALLATION

Before connecting the beer dispenser, let the unit sit upright for approximately 2 hours. This will

reduce the possibility of a malfunction in the cooling system from handling during transportation.

Clean the interior surface with warm water and a clean cloth.

This appliance is designed to be free-standing only and should not be recessed or built-in.

Place your beer dispenser on a ﬂoor that is strong enough to support the unit when fully loaded.

Allow three inches of space between the back and sides of the beer dispenser to allow proper air

circulation for the compressor to cool.

Keep the beer dispenser away from direct sunlight and heat sources. Direct sunlight may affect

the acrylic coating and heat sources may increase electrical consumption. Extremely cold ambient

temperatures may also cause the unit to preform poorly.

Keep the unit out of moist areas.

Plug the unit into an exclusive, properly installed, grounded wall outlet. Do not, under any

circumstances, cut or remove the third prong from the power cord.

After plugging in the unit, allow it to cool down for 2-3 hours before placing any contents in the

compartment.

•

GROUNDING INSTRUCTIONS

This beer dispenser must be grounded. In the event of an electrical short circuit, grounding reduces risk

of electric shock by providing an escape wire for the electric current.

WARNING: Improper use of the grounding plug can result in risk of electric shock.

ELECTRICAL REQUIREMENTS

The electrical requirements for this beer dispenser are 115/120V, 60Hz electrical outlet with three-

prong ground.

The beer dispenser is equipped with a 3-prong grounding plug. It must be plugged into a wall outlet

properly installed and grounded.

Extension cords are not recommended.

Do not unplug the beer dispenser by pulling the power cord. Always grip the plug ﬁrmly and pull

straight out from the socket.

•

PRODUCT DIAGRAM

Beer tower

Plastic gasket

Safety guard rail

Drip tray

Adjustable thermostat

CO2regulator

CO2gas cylinder

CO2gas cylinder support

Evaporator

Reversible door

Beer keg (not included)

Metal plate

Metal gasket (2)

Castors with lock (4)

10.

11.

12.

13.

14.

INSTALLATION INSTRUCTIONS

INSTALLING THE CASTORS

Install the four castors provided into the unit’s bottom. The two metal gaskets are used on the front

two castors.

•

INSTALLING THE CO2CYLINDER SUPPORT

Install the metal support provided onto the 4 studs located on

the exterior back wall.

Align the holes in the support with the studs and push down

ﬁrmly.

•

INSTALLING THE CO2CYLINDER

Install your fully-charged cylinder into the support stand.•

INSTALLING THE CO2REGULATOR

Attach the CO2regulator to the cylinder by turning the

regulator nut onto cylinder valve, making sure washer is

securely inserted into connecting nut.

Tighten using an adjustable wrench (not supplied) and assure

there are no leaks.

•

INSTALLING THE CO2AIR LINE TO OUTSIDE CABINET

Remove plug located at the exterior back (top left corner).

Save it for later use if you decide to convert unit to an “all-

refrigerator”.

Insert the open end of the air line (red) from the cabinet

through the uncovered hole.

•

INSTALLING THE CO2AIR LINE TO REGULATOR

Attach the open end of the red hose to the hose barb

connection on the regulator.

Secure hose by using one of the provided clamps.

Use pliers/screwdriver to tighten clamp and assure no

leaks.

•

INSTALLATION INSTRUCTIONS (continued)

INSTALLING THE BEER TOWER

Remove the top plug by twisting and pulling out, saving it for later use if you decide to convert unit

to an “all-refrigerator”.

Unravel the beer line (clear hose) from the tower and insert the beer line and wing nut through the

uncovered hole on top.

Lock the beer tower assembly to the top and make sure to position the beer faucet so it is aligned with

the cabinet front (6 o’clock position). To do so, align the bottom of the beer tower to the 3 grooves on

the top cabinet and tighten by hand clockwise to properly lock.

•

INSTALLING THE PROTECTIVE METAL PLATE

This plate should always be installed when the keg is in place to protect against unnecessary damage

to the ﬂoor of the cabinet.

•

INSTALLING THE PROTECTIVE METAL PLATE

Position the beer keg directly in front of the open door.

Using keg handles only, carefully lift the beer keg.

To place the beer keg inside the cabinet, brace your

knees behind the beer keg. Lift the front of the keg just

enough so the front edge of the keg is resting on the

front edge of the Beer dispenser bottom cabinet.

Grasp the keg handles and slide it all the way into the

cabinet.

•

INSTALLATION INSTRUCTIONS (continued)

INSTALLING THE KEG COUPLER

Insert the provided keg coupler into the locking neck of the beer keg and turn it clockwise to lock into

position, making sure the keg coupler is in the closed position.

•

INSTALLING THE CO2AIR LINE HOSE

Attach the end of the provided air line hose (red) to the hose connection on the keg coupler.

Secure hose by using the connector and make sure there are no leaks.

•

INSTALLING THE BEER TOWER TO COUPLER

Make sure the washer is properly inserted into the wing nut.

Place wing nut into the top of the coupler turning until tight.

•

INSTALLING THE CO2CYLINDER MAIN VALVE

Make sure the secondary shut-off valve is closed.

To open the main CO2cylinder valve, slowly turn the main valve counter-clockwise until fully open.

The needle on the gauge will start to climb.

•

ADJUSTING THE CO2REGULATOR

Release the adjustment lock nut.

Using a ﬂat screwdriver, turn the regulator screw. If you want to increase the low pressure, rotate

screw clockwise. By rotating it counter clockwise, low pressure will be decreased.

When the required operating pressure is attained, retighten lock nut.

Open secondary shut off valve to let CO2ﬂow into the keg.

•

INSTALLATION INSTRUCTIONS (continued)

INSTALLING THE PLASTIC FAUCET LEVER

Attach the provided black plastic lever (pull handle) on

the top of the faucet tightening it by hand clockwise

until the end, holding in the silver snug underneath so

it does not move.

If there is a small drip from the faucet, you may have

tightened the plastic lever too much. Unscrew the

silver snug counter-clockwise one turn.

•

CONVERTING TO AN “ALL-REFRIGERATOR”

Turn the control knob to the “OFF” position.

Close the main valve on the CO2cylinder.

Close the secondary shut-off valve on the regulator pipe.

Close the connection between the beer keg and the keg coupler.

Drain any remaining beer from the lines.

Disconnect the beer line and CO2air line from the keg coupler.

Remove the beer keg.

Remove the keg coupler.

Disconnect the air line from the CO2cylinder.

Remove the CO2air line from cabinet plug.

Replace the air line rear cabinet plug.

Remove the beer tower and pull the beer line through the top of the cabinet.

Replace the top cabinet plug.

Order the optional wire shelves and install them on the side supports.

Adjust temperature as desired.

•

REVERSING THE DOOR

Loosen and remove the three door hinge screws from the bottom hinge on the lower right base and

remove the hinge.

Remove the door and set aside.

Remove the plug from the top left corner of the door and place in top right of door.

Loosen and remove the two door hinge screws on the top right of the unit.

Place the top hinge on the left side of the unit front and, using the two previously removed screws,

tighten.

Remove the stopper from the bottom left side of the unit by removing the screw and replace on the

right side of the unit where the bottom hinge was previously removed.

Place door on top hinge of unit and replace the bottom hinge to the bottom left of the unit using the

three screws and tighten.

•

Table of contents

Other Sunbeam Kitchen Appliance manuals

Sunbeam

Sunbeam Pie Magic PM4210 User manual

Sunbeam

Sunbeam SBWC033A1S Assembly instructions

Sunbeam

Sunbeam CKSBSK12B-033 User manual

Sunbeam

Sunbeam Pie Magic PM040 Operational manual

Sunbeam

Sunbeam EasyClean Snack-For-Four GR6400 Operational manual

Sunbeam

Sunbeam JE8500 Operational manual

Sunbeam

Sunbeam CAFE PRESS GR8400 Operational manual

Sunbeam

Sunbeam Food Slicer User manual

Sunbeam

Sunbeam FPSBFCM40 User manual

Sunbeam

Sunbeam DIAMONDFORCE WWM7000DF User manual

Sunbeam

Sunbeam FP6000 User manual

Sunbeam

Sunbeam ES9600 User manual

Sunbeam

Sunbeam JE8600 User manual

Sunbeam

Sunbeam GR8450 Cafe Press User manual

Sunbeam

Sunbeam Snack Heroes BW1100 User manual

Sunbeam

Sunbeam 4804 Technical specifications

Sunbeam

Sunbeam Snack Heroes CC4000 User manual

Sunbeam

Sunbeam FPSBPP7310-033 User manual

Sunbeam

Sunbeam CAFE PRESS GR8400 Operational manual

Sunbeam

Sunbeam Cafe Creamy EM0180 Service manual

Sunbeam

Sunbeam Pattie CC3200 Operational manual

Sunbeam

Sunbeam Pie Magic Traditional 4 Up User manual

Sunbeam

Sunbeam VersaCook MU2000 X5 Operational manual

Sunbeam

Sunbeam FoodSaver VAC430 User manual

Popular Kitchen Appliance manuals by other brands

Tayama

Tayama TYG-35AF instruction manual

AEG

AEG 43172V-MN user manual

REBER

REBER Professional 40 Use and maintenance

North American

North American BB12482G / TR-F-04-B-NCT-1 Assembly and operating instructions

Presto

Presto fountain popper instruction manual

Westmark

Westmark 1035 2260 operating instructions

Zanussi

Zanussi ZCG64396XA user manual

HOFFEN

HOFFEN SM-9302M instruction manual

Philips

Philips HD3133 user manual

Ronco

Ronco Beef Jerky User guide and recipes

Hendi

Hendi 470411 user manual

Livoo

Livoo MEN386 user manual

Vogue

Vogue D446 instruction manual

croydon

croydon WR-10313-700 instruction manual

ADE

ADE AUTOMATIC-L operating instructions

Chefman

Chefman RJ43-SQ Series user guide

Vacmaster

Vacmaster VP680 user guide

Jetmaster

Jetmaster 900HG operating instructions