Smeg SA9065LPG User manual

Contents

1. INSTRUCTIONS FOR SAFE AND PROPER USE________________ 4

2. INSTALLATION OF THE APPLIANCE_________________________ 6

3. GAS CONNECTION_______________________________________ 7

4. ADAPTATION TO DIFFERENT TYPES OF GAS _______________ 10

5. FINAL OPERATIONS_____________________________________ 12

6. DESCRIPTION OF CONTROLS ____________________________ 14

7. USE OF THE HOB _______________________________________ 21

8. USE OF THE OVEN______________________________________ 23

9. AVAILABLE ACCESSORIES _______________________________ 25

10. COOKING HINTS________________________________________ 26

11. CLEANING AND MAINTENANCE ___________________________ 32

12. EXTRAORDINARY MAINTENANCE _________________________ 34

13. PROBLEMS AND CAUSES ________________________________ 36

Thank you for choosing our product.

We advise you to read this manual carefully. It contains all necessary

instructions for maintaining unaltered the appearance and functional

qualities of the cooker.

INSTRUCTIONS FOR THE INSTALLER: these are for the authorised

persons who must carry out a suitable check of the gas system, install

the appliance, set it functioning and carry out an inspection test.

INSTRUCTIONS FOR THE USER: these contain user advice,

description of the commands and the correct procedures for cleaning

and maintenance of the appliance.

Introduction

1. INSTRUCTIONS FOR SAFE AND PROPER USE

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND

THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE

PLACE FOR THE WHOLE WORKING LIFE OF THE COOKER. WE ADVISE

READING THIS MANUAL AND ALL THE INSTRUCTIONS THERE IN BEFORE

USING THE COOKER.

INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN

ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS

INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT

REGULATIONS IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY

OUT THE FOLLOWING FUNCTIONS: COOKING AND HEATING-UP OF FOOD.

ALL OTHER USES ARE CONSIDERED IMPROPER.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER

USE.

DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT. SEPARATE

THE VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST

SPECIAL GARBAGE COLLECTION CENTRE.

IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED

ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES.

IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION

TEST OF THE APPLIANCE, FOLLOWING THE INSTRUCTIONS BELOW.

SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE

SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE.

NEVER ATTEMPT TO REPAIR THE APPLIANCE.

ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION

(OFF) WHEN YOU FINISH USING THE HOB.

NEVER PUT INFLAMMABLE OBJECTS INTO AN OVEN: IF THEY CATCH FIRE

THEY COULD CAUSE A FIRE IN THE HOME.

THE I.D. PLATE WITH TECHNICAL DATA, REGISTRATION NUMBER AND

BRAND NAME IS POSITIONED VISIBLY IN THE STORAGE COMPARTMENT.

THE PLATE MUST NOT BE REMOVED.

DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS

ON THE HOB GRIDS.

Introduction

DURING USE THE APPLIANCE BECOMES VERY HOT. TAKE CARE NOT TO

TOUCH THE HEATING ELEMENTS INSIDE THE OVEN.

DO NOT USE CONTAINERS OR BROILERS THAT EXTEND BEYOND THE

OUTER PERIMETER OF THE HOB.

IF THE APPLIANCE IS TO BE POSITIONED ON A PLATFORM IT MUST BE

INSTALLED IN SUCH A WAY AS TO PREVENT IT FROM SLIPPING OFF THE

FORMER.

THE APPLIANCE IS DESIGNED FOR USE BY ADULTS. DO NOT ALLOW

CHILDREN OR INFIRM PERSONS TO GO NEAR OR PLAY WITH IT.

DURING USE THE APPLIANCE BECOMES HOT. CARE SHOULD BE TAKEN

TO AVOID TOUCHING THE HEATING ELEMENTS INSIDE THE OVEN. KEEP

CHILDREN AWAY FROM THE OVEN.

REPLACED APPLIANCES MUST BE TAKEN TO A SPECIAL GARBAGE

COLLECTION CENTRE.

WHERE THIS APPLIANCE IS INSTALLED IN MARINE CRAFT OR IN

CARAVANS, IT SHALL NOT BE USED AS A SPACE HEATER.

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT

IS IN OPERATION.

BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE LABELS AND

PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED.

The manufacturer declines all responsibility for damage to persons

or things caused by non-observance of the above prescriptions or by

interference with any part of the appliance or by the use of non-original

spares.

Instructions for the installer

2. INSTALLATION OF THE APPLIANCE

It is the law that all gas appliances are installed by authorised persons.

Clearance around the cooker must comply with the requirements of

AS5601.

2.1 Electrical connection

Make sure that the power line voltage matches the specifications

indicated on the rating plate located inside the storage compartment.

This rating plate must never be removed.

On the power line, install a two-pole cut-off device with contact cut-off

distance greater than or equal to 3 mm, located in an easily accessible

position near the unit.

The wire section on the cable must not be less

than 2.5 mm2(3 x 2.5 cable), keeping in mind

that the end to be connected to the cooker

must have the ground wire (yellow-green)

longer by at least 20 mm. Use only the special

cables available at our Service Centres.

The manufacturer declines all responsibility for damage to persons

or things caused by non-observance of the above prescriptions or by

interference with any part of the appliance.

Overall dimensions: location of gas and electrical connection points (all

measures in mm).

A 60

B 410

C 60

D 70

Instructions for the installer

3. GAS CONNECTION

This appliance is suitable for installation with

Natural Gas or LPG (liquid petroleum gas). Refer to

page 12 for the relevant burner pressure and

appropriate injector sizes. When the appliance is to

be connected to Natural Gas then the pressure

regulator supplied must be fitted to the gas inlet. A

test point (for checking the gas pressure) is

supplied either with the regulator or as a separate

fitting in the case of LPG (propane) appliances.

Connection of the appliance to the gas supply must

be in accordance with the requirements of AS5601.

A ½” BSP connector at the inlet is recommended

and the gas supply line to the appliance must be of

adequate length to allow sufficient withdrawal of

appliance for service or disconnection and be:

1. annealed copper pipe or;

2. flexible hose according to AS/NZ1869 & be at

least Class “B”, 10 mm diameter.

The appliance must be installed with provision to allow the gas to be

turned off and disconnected for servicing and removal of the appliance

as required from the gas supply.

Before the appliance is operated make certain all relevant parts are

placed in the correct position.

When the installation is completed the installation connections of

appliance will require to be leak tested, the burner operating pressure

and flame checked and adjusted.

Warranty service calls do not cover these adjustments!

To check the operating pressure of the appliance it is recommended at

least 2 large size burners are used. Ensure appliance is secured to wall

when installation is completed.

N.G. A regulator must be fitted to the ½ BSP thread at the rear of the

appliance. An approved manual shut-off valve must be installed. The

N.G. regulator must be checked and adjusted to 1.0kPa after installation.

LPG: Can be connected to the inlet fitting

directly. The pressure must be checked to

ensure it is operating at 2.75kPa. A separate

test point fitting must be installed between the

piping & the appliance for the pressure to be

checked to ensure it is operating at 2.75kPa.

Instructions for the installer

3.1 Room ventilation

Caution – This cooker may only be installed and operated in rooms

permanently ventilated in accordance with current regulations. For

proper operation of a gas appliance it is essential for the air necessary

for combustion of the gas to be able to flow naturally into the room. Air

must flow directly into the room through openings in its outside walls.

This (these) opening (s) must have a free passage cross-section of at

least 100 cm2, or 200 cm2for appliances not equipped with gas safety

device. These openings must be constructed so that they cannot be

obstructed indoors or outdoors, and should preferably be close to the

floor on the side opposite to the combustion gas discharge point. If it is

not possible to make the openings in the room where the cooker is

installed, the necessary air may be taken from an adjoining room,

proveded it is not a bedroom or a room with fire risk.

3.2 Clearance above and around domestic cookers

Extract from AS5601

Instructions for the installer

REQUIREMENTS

1Overhead clearances – (Measurement A)

Range hoods and exhaust fans shall be installed in accordance with

the manufacturer’s instructions. However, in no case shall the

clearance between the highest part of the hob of the cooking

appliance and a range hood be less than 600 mm or, for an overhead

exhaust fan, 750 mm.

Any other downward facing combustible surface less than 600 mm

above the highest part of the hob shall be protected for the full width

and depth of the cooking surface area in accordance with Clause

5.12.1.2. However, in no case shall this clearance to any surface be

less than 450 mm.

2Side clearances – (Measurements B& C)

Where B, measured from the periphery of the nearest burner to any

vertical combustible surface, is less than 200 mm, the surface shall

be protected in accordance with Clause 5.12.1.2 to a height Cof not

less than 150 mm above the hob for the full dimension (width or

depth) of the cooking surface area. Where the cooking appliance is

fitted with a ‘splashback’, protection of the rear wall is not required.

3Additional requirements for Freestanding and Elevated Cooking

Appliaces – (Measurements D& E)

Where D, the distance from the periphery of the nearest burner to a

horizontal combustible surface is less than 200 mm, then Eshall be

10 mm or more, or the horizontal surface shall be above the trivet.

See insets above.

NOTES

1Requirement 3 does not apply to a freestanding or elevated

cooking appliance which is designed to prevent flames or the

cooking vessels from extending beyond the periphery of the

appliance.

2The ‘cooking surface area’ is defined as that part of the

appliance where cooking normally takes place and does not

include those parts of the appliance containing control knobs.

3For definition of hob, see Clause 1.4.64.

4For definition of trivet, see Clause 1.4.109.

5Consideration is to be given to window treatments when

located near cooking appliances. See Clause 5.3.4.

Instructions for the installer

4. ADAPTATION TO DIFFERENT TYPES OF GAS

Before performing any cleaning or maintenance work, disconnect the

appliance from the mains.

The hob of the cooker is adjusted for use with either natural gas at a

pressure of 1.0kPa (SA 9066 – SA 9065) or LPG (liquid petroleum gas)

at a pressure of 2.75 kPa (SA 9066 LPG – SA 9065 LPG). If used with

other types of gas, you have to replace the nozzles, then adjust the

minimum flame on the gas taps. For nozzle replacement and burner

adjustment operate as described in the following paragraph.

4.1 Replacement of nozzles on the hob

This operation requires no primary air regulation.

1. Extract the grids and remove all the caps and flame-spreader

crowns;

2. unscrew the burner nozzles with a 7 mm socket wrench;

3. replace the nozzles according to the type of gas to be used and the

description in paragraph "3.2 Burner and nozzle characteristics

table".

4. Replace the burners in the correct position.

Instructions for the installer

4.2 Burner and nozzle characteristics table

Burner

LPG (LIQUID PETROLEUM GAS) –2.75 KPa

Nominal gas

consumption

(MJ/h)

Turn-down gas

consumption

(MJ/h)

Injector

(mm)

Auxiliary 3.9 1.5 0,54

Semi rapid 6.3 1.5 0,68

Rapid 10 2.7 0,88

WOK 12.8 5.4 1,00

Fish pan 7 2.2 0,72

Burner

NG –1.0 KPa

Nominal gas

consumption

(MJ/h)

Turn-down gas

consumption

(MJ/h)

Injector

(mm)

Auxiliary 4 1.5 0,90

Semi rapid 7 1.5 1,20

Rapid 12 2.7 1,55

WOK 15 5.4 1,75

Fish pan 8 2.2 1,26

Instructions for the installer

5. FINAL OPERATIONS

After replacing the nozzles, reposition the flame-spreader crowns, the

burner caps and the grids.

5.1 Adjustment of the hob burner minimum level for natural gas

Light the burner and take it to the minimum .

Remove the gas tap knob and turn the

adjustment screw inside of the tap shaft

(depending on the model) until there is a regular

minimum flame. Replace the knob and check

burner flame stability: (rapidly turning the knob

from maximum to minimum position, the flame

should not go out). Repeat the operation on all

the gas taps.

5.2 Arrangement of the burners on the hob

Burners

1 Auxiliary

2 Semi rapid

3 Rapid

4 Wok

7 Fish burner

This manual suits for next models

Table of contents

Popular Kitchen Appliance manuals by other brands

Tayama

Tayama TYG-35AF instruction manual

AEG

AEG 43172V-MN user manual

REBER

REBER Professional 40 Use and maintenance

North American

North American BB12482G / TR-F-04-B-NCT-1 Assembly and operating instructions

Presto

Presto fountain popper instruction manual

Westmark

Westmark 1035 2260 operating instructions

Zanussi

Zanussi ZCG64396XA user manual

HOFFEN

HOFFEN SM-9302M instruction manual

Philips

Philips HD3133 user manual

Ronco

Ronco Beef Jerky User guide and recipes

Hendi

Hendi 470411 user manual

Livoo

Livoo MEN386 user manual

Vogue

Vogue D446 instruction manual

croydon

croydon WR-10313-700 instruction manual

ADE

ADE AUTOMATIC-L operating instructions

Chefman

Chefman RJ43-SQ Series user guide

Vacmaster

Vacmaster VP680 user guide

Jetmaster

Jetmaster 900HG operating instructions