Prorack K319 User manual
K319
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 2 x 4
Revision No: 6F 1
Fitting Kit K319
MAX kgs (lbs)
W/P WHD
Toyota
Corolla, 4dr Sedan 07-13 ZA 40 kgs (88 lbs) 40 kgs (88 lbs)
Corolla, 4dr Sedan 07-13 EU 40 kgs (88 lbs) 40 kgs (88 lbs)
Corolla, 4dr Sedan 07-13 CN 40 kgs (88 lbs) 40 kgs (88 lbs)
Corolla, 4dr Sedan 09-13 US 40 kgs (88 lbs) 40 kgs (88 lbs)
Corolla, 4dr Sedan May 07-13 AU 40 kgs (88 lbs) 40 kgs (88 lbs)
Corolla, 4dr Sedan May 07-13 NZ 40 kgs (88 lbs) 40 kgs (88 lbs)
2
Fitting Kit K319
X
A B C 1 2 3
Corolla, 4dr Sedan 07-13 (ZA) -250mm 450mm - 886mm 880mm -
-9 -13/16ths" 17 3/4ths" - 34 7/8ths" 34 5/8ths" -
Corolla, 4dr Sedan 07-13 (EU) -250mm 450mm - 886mm 880mm -
-9 -13/16ths" 17 3/4ths" - 34 7/8ths" 34 5/8ths" -
Corolla, 4dr Sedan 07-13 (CN) -250mm 450mm - 886mm 880mm -
-9 -13/16ths" 17 3/4ths" - 34 7/8ths" 34 5/8ths" -
Corolla, 4dr Sedan 09-13 (US) -250mm 450mm - 886mm 880mm -
-9 -13/16ths" 17 3/4ths" - 34 7/8ths" 34 5/8ths" -
Corolla, 4dr Sedan May 07-13 (AU) -250mm 450mm - 886mm 880mm -
-9 -13/16ths" 17 3/4ths" - 34 7/8ths" 34 5/8ths" -
Corolla, 4dr Sedan May 07-13 (NZ) -250mm 450mm - 886mm 880mm -
-9 -13/16ths" 17 3/4ths" - 34 7/8ths" 34 5/8ths" -
3
Fitting Kit EN
K319
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4
Fitting Kit EN
K319
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5
Fitting Kit EN
K319
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 218B
B = 414A
6
Fitting Kit EN
K319
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Fit rubber pad (supplied with crossbar) to
foot.
7
Fitting Kit EN
K319
●Make sure the pad fits into the holes
underneath the foot.
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Clamps directly to edge of roof under the
doors
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
8
Fitting Kit EN
K319
●Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
9
Fitting Kit EN
K319
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Other manuals for K319
1
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K598 User manual
Prorack
Prorack K138 User manual
Prorack
Prorack K828 User manual
Prorack
Prorack K340W User manual
Prorack
Prorack K408 User manual
Prorack
Prorack K541 User manual
Prorack
Prorack K707 User manual
Prorack
Prorack K674 User manual
Prorack
Prorack K194 Operation and installation manual
Prorack
Prorack K671 User manual
Prorack
Prorack K304 User manual
Prorack
Prorack K958 User manual
Prorack
Prorack PR3104 User manual
Prorack
Prorack K848 User manual
Prorack
Prorack K462 User manual
Prorack
Prorack K456 User manual
Prorack
Prorack K540 User manual
Prorack
Prorack K156 User manual
Prorack
Prorack K387 User manual
Prorack
Prorack K070 User manual
