Prorack K671 User manual
K671
Fitting Kit
EN Fitting Instructions for Basic Carrier CAUTION: Professional
installation recommended
x 4 x 4 x 1 x 4
x 8 x 8 x 4 x 4
Revision No: 6D 1
Fitting Kit K671
x 4 x 4 x 4 x 4
x 4
2
Fitting Kit K671
MAX kgs (lbs)
W/P WHD
Chevrolet
Colorado Crew Cab LT/LTZ, 4dr Truck 13-+ US 75 kgs (165 lbs) 100 kgs (220 lbs)
Colorado Crew Cab LT/LTZ, 4dr Ute 13-+ EU 75 kgs (165 lbs) 100 kgs (220 lbs)
Holden
Colorado Crew Cab LT/LTZ, 4dr Ute 12-+ NZ 75 kgs (165 lbs) 100 kgs (220 lbs)
Colorado Crew Cab LT/LTZ, 4dr Ute 12-+ AU 75 kgs (165 lbs) 100 kgs (220 lbs)
Isuzu
D Max LS Double Cab, 4dr Ute 12-+ NZ 75 kgs (165 lbs) 100 kgs (220 lbs)
D Max Eiger, 4dr Ute 12-+ EU 75 kgs (165 lbs) 100 kgs (220 lbs)
D Max Yukon, 4dr Ute 12-+ EU 75 kgs (165 lbs) 100 kgs (220 lbs)
D Max LX Double Cab, 4dr Ute 13-+ ZA 75 kgs (165 lbs) 100 kgs (220 lbs)
D Max LS Crew Cab, 4dr Ute Jul 12-+ AU 75 kgs (165 lbs) 100 kgs (220 lbs)
D Max LS-U Crew Cab, 4dr Ute Jul 12-+ AU 75 kgs (165 lbs) 100 kgs (220 lbs)
D Max LS-M Crew Cab, 4dr Ute Jul 12-+ AU 75 kgs (165 lbs) 100 kgs (220 lbs)
3
Fitting Kit EN
K671
CAUTION:
●Professional installation recommended.
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●This kit fits type A, B, C and D.
4
Fitting Kit EN
K671
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5
Fitting Kit EN
K671
●Attaches to factory-fitted mounting points
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
6
Fitting Kit EN
K671
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
Fitment
●There are 4 concealed mounting points
hidden by the vehicles rubber insert on the
roof.
●Measure from the front of the rubber insert
and make a mark at 355mm and 1245mm.
●From these 2 marks measure 25mm
forward and 25mm back and mark a line
across the rubber insert.
●Carefully lift the rubber insert by hand to
reveal the mounting points as shown, only
lift the minimum amount required to reveal
the mounting point.
●Note: Do not use sharp objects or tools to
lift the rubber moulding.
●Note: Take care when lifting the rubber
insert not to kink or bend it.
●Note: The mounting points are covered
with sealant.
7
Fitting Kit EN
K671
●Now cut the rubber insert at the 2 lines you
marked in the earlier instruction. Once cut
you should end up with 4 x 50mm pieces of
the rubber insert.
●Note: Be careful of sharp edges after
cutting the rubber insert.
●Remove one side of adhesive tape
backing. Apply to underside of rubber
insert as shown. Remove second backing,
then apply downward pressure onto
vehicle.
●To reveal the screw thread in the mounting
points, remove the sealant covering them
with a sharp tool.
8
Fitting Kit EN
K671
●Remove sealant as shown.
●Apply protective strip as shown.
Trim if required.
●Assemble as shown.
●A = 8mm bolt
B = Spring washer
C = Flat washer
D = Rubber seal
E = Protective strip
●Place rubber seal over bolt thread as
shown.
●Place the clamps into position as pictured
at the 4 points, ensure the clamp is
orientated the right way in the vehicle
channel.
●Using 5mm hex key supplied with this kit,
fully tighten the M8 dome head bolt and
washer supplied to 5Nm (3.7 ft lb) hand
tight.
9
Fitting Kit EN
K671
●Select coach bolt and insert through metal
clamp slot.
●Using the 10mm (3/8") spanner supplied
with the crossbars, tighten the nut to 5Nm
(3.7 ft lb) hand tight.
●A = Coach bolt
B = Washer
C = Nut
●Assemble as shown.
●Refer to the underside of the pad for the
part number.
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack WHISPBAR S41 Operation and installation manual
Prorack
Prorack K322 Operation and installation manual
Prorack
Prorack K543 User manual
Prorack
Prorack K452 User manual
Prorack
Prorack K421 User manual
Prorack
Prorack K387 User manual
Prorack
Prorack K800 User manual
Prorack
Prorack K1234 User manual
Prorack
Prorack EXP360 User manual
Prorack
Prorack K766 User manual
Prorack
Prorack K776 Operation and installation manual
Prorack
Prorack K569 User manual
Prorack
Prorack K349 User manual
Prorack
Prorack K527 User manual
Prorack
Prorack K409 User manual
Prorack
Prorack WHISPBAR S45 Operation and installation manual
Prorack
Prorack K178 User manual
Prorack
Prorack K577 Operation and installation manual
Prorack
Prorack K073 User manual
Prorack
Prorack WHISPBAR S53 Operation and installation manual
