Aries 203015 User manual
PAGE 1 • 203015-INS-RB • 800.798.0813 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM
Notes and Maintenance
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
To protect the product, wax after installing. Regular waxing is recommended to
add a protective layer over the finish. Do not use any type of polish or wax that may
contain abrasives that could damage the finish.
For gloss black finishes, mild soap may be used to clean the product.
Level of Difficulty
Easy
Tools Required
Rachet Tape measure
Socket, 17mm Wrench, 17mm
Level Hex bit, 6mm
Scan
for helpful
install tips
INSTALLATION MANUAL 203015
Parts List
1Driver / left side bar
1Passenger / right side bar
2Mounting bracket, front
2Mounting bracket, rear
8Clip on nut, 10mm
8Button head bolts, 10mm x 25mm
8Lock washer, 10mm
32 Flat washer, 10mm
8Nylock nut, 10mm
16 Hex bolt, 10mm x 30mm
Product Image
Brackets
Front
Rear
ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 800.798.0813 • 203015-INS-RB • PAGE 2
Step 1
Starting on the driver side of the vehicle,
locate the three mounting locations along
the rocker panel.
This installation will use the
front and rear mounting locations.
The mounting brackets are specific
to a front or rear mounting location.
When mounting the brackets have
the cradle facing towards the middle
of the truck for proper placement.
Step 2
Starting at the front of the driver side,
remove the factory tape covering the
mounting holes.
On the inner rocker panel, insert a 10mm
clip-nut onto each mounting location.
Step 3
Attach the top of the bracket by
threading two 10mm hex bolts and
flat washers into the 10mm clip nuts
from step 2.
Insert a 10mm hex bolt and flat washer
into the bottom mounting holes and
secure with a second flat washer
and nylock nut.
Snug the hardware,
but do not fully tighten.
Step 4
Repeat steps 1 through 3 for installing
the rear mounting bracket.
PAGE 3 • 203015-INS-RB • 800.798.0813 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM
Step 5
To determine the front of a side bar, the
measurement from the end of the side
bar to the center of the rivet nut should
be 15 1/2".
Step 6
Carefully mount the driver side bar into
place.
Attach the side bar to the mounting
bracket using a 10mm button head bolt
and flat washer.
Snug the hardware,
but do not fully tighten.
Step 7
Finish the passenger side bar installation
by repeating the installation process used
on steps 5 and 6 on the driver side.
Level and adjust the side bars to the
desired position and tighten all hardware.
Step 8
Congratulations on the installation of
your new ARIES 3" round side bars.
With the side bars installed, periodic
inspections should be performed to ensure
all mounting hardware remains tight.
To protect your investment, see the
'Notes and Maintenance' section on
the first page of this instruction manual.
Table of contents
Other Aries Automobile Accessories manuals
Aries
Aries 2055122 User manual
Aries
Aries 2055100 User manual
Aries
Aries 2051101 User manual
Aries
Aries 25630AB User manual
Aries
Aries 205045-2 User manual
Aries
Aries 202003 User manual
Aries
Aries 2153000 User manual
Aries
Aries 2055117 User manual
Aries
Aries S225044 User manual
Aries
Aries AL235017 User manual
Aries
Aries 205039 User manual
Aries
Aries 202020 User manual
Aries
Aries AL239042 User manual
Aries
Aries S224054 User manual
Aries
Aries 2081004 User manual
Aries
Aries 2164003 User manual
Aries
Aries Avicenum LYMPHO 360 User manual
Aries
Aries 203039 User manual
Aries
Aries 1500201 User manual
Aries
Aries 205008-2 User manual
