Prorack K541 User manual
K541
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 2 x 2
x 2 x 2 x 1 x 1
Revision No: 4D 1
Fitting Kit K541
MAX kgs (lbs)
W/P WHD
Renault
Megane Mk3, 5dr Hatch 09-+ ZA 65 kgs (143 lbs) 65 kgs (143 lbs)
Megane Mk3, 5dr Hatch 09-+ CN 65 kgs (143 lbs) 65 kgs (143 lbs)
Megane Mk3, 5dr Hatch 09-Dec 15 EU 65 kgs (143 lbs) 65 kgs (143 lbs)
Megane Mk3, 5dr Hatch 09-Nov 16 AU 65 kgs (143 lbs) 65 kgs (143 lbs)
2
Fitting Kit K541
X
A B C 1 2 3
Megane Mk3, 5dr Hatch 09-+ (ZA) -350mm 345mm - 885mm 845mm -
-13 -3/4ths" 13 9/16ths" - 34 13/16ths" 33 1/4ths" -
Megane Mk3, 5dr Hatch 09-+ (CN) -350mm 345mm - 885mm 845mm -
-13 -3/4ths" 13 9/16ths" - 34 13/16ths" 33 1/4ths" -
Megane Mk3, 5dr Hatch 09-Dec 15 (EU) -350mm 345mm - 885mm 845mm -
-13 -3/4ths" 13 9/16ths" - 34 13/16ths" 33 1/4ths" -
Megane Mk3, 5dr Hatch 09-Nov 16 (AU) -350mm 345mm - 885mm 845mm -
-13 -3/4ths" 13 9/16ths" - 34 13/16ths" 33 1/4ths" -
3
Fitting Kit EN
K541
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4
Fitting Kit EN
K541
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5
Fitting Kit EN
K541
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 752A
B = 753A
C = 754A
6
Fitting Kit EN
K541
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
7
Fitting Kit EN
K541
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 11-04-250
B = 11-04-251
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
8
Fitting Kit EN
K541
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Locate vehicle's fixed points.
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Clamps directly to edge of roof under the
doors, pin locates in hole on vehicle
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
9
Fitting Kit EN
K541
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K488 User manual
Prorack
Prorack K903 User manual
Prorack
Prorack K062 User manual
Prorack
Prorack K507 User manual
Prorack
Prorack K094 User manual
Prorack
Prorack K431 User manual
Prorack
Prorack K832 Operation and installation manual
Prorack
Prorack K382 User manual
Prorack
Prorack K485 User manual
Prorack
Prorack K361 User manual
Prorack
Prorack K718 Operation and installation manual
Prorack
Prorack PR3077 User manual
Prorack
Prorack PR3077 User manual
Prorack
Prorack K453 User manual
Prorack
Prorack K424 User manual
Prorack
Prorack K577W User manual
Prorack
Prorack K1012 User manual
Prorack
Prorack K374 User manual
Prorack
Prorack K129 User manual
Prorack
Prorack K802 User manual
