Prorack K707 User manual
K707
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 1 x 1
x 1 x 1 x 1 x 1
x 1 x 1 x 1 x 1
Revision No: 2A 1
Fitting Kit K707
MAX kgs (lbs)
W/P WHD
Audi
A7 Sportback, 5dr Hatch 11-+ NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
A7 Sportback, 5dr Hatch 11-+ AU 50 kgs (110 lbs) 50 kgs (110 lbs)
A7 Sportback, 5dr Hatch 11-+ ZA 50 kgs (110 lbs) 50 kgs (110 lbs)
A7 Sportback, 5dr Hatch 11-+ EU 50 kgs (110 lbs) 50 kgs (110 lbs)
A7 Sportback, 5dr Hatch 11-+ US 50 kgs (110 lbs) 50 kgs (110 lbs)
2
Fitting Kit EN
K707
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3
Fitting Kit EN
K707
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
4
Fitting Kit EN
K707
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = A025
B = A026
C = A027
D = A028
5
Fitting Kit EN
K707
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 293A
B = 294A
C = 295A
D = 296A
6
Fitting Kit EN
K707
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
●Clamps onto anchor points under rubber
door frame mouldings
7
Fitting Kit EN
K707
●The rubber seal must be peeled back from
the vehicle body to allow the clamp to be
inserted between the vehicle body and the
rubber seal.
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Press adjusting screw to adjust the leg
positions on the crossbar.
8
Fitting Kit EN
K707
●Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
●Tighten locking screw on both legs evenly,
3 Nm (2.2 ft lb).
●Check crossbar is securely attached to the
vehicle.
9
Fitting Kit EN
K707
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K945 User manual
Prorack
Prorack K319 User manual
Prorack
Prorack K604 User manual
Prorack
Prorack PR3600 User manual
Prorack
Prorack K757 User manual
Prorack
Prorack K683 User manual
Prorack
Prorack K335 User manual
Prorack
Prorack K394 User manual
Prorack
Prorack PR3213 User manual
Prorack
Prorack K182 Operation and installation manual
Prorack
Prorack K382 User manual
Prorack
Prorack K340W User manual
Prorack
Prorack K324 User manual
Prorack
Prorack K133 Operation and installation manual
Prorack
Prorack S16 User manual
Prorack
Prorack K564 User manual
Prorack
Prorack K432 User manual
Prorack
Prorack K1214 User manual
Prorack
Prorack K105 User manual
Prorack
Prorack K102 User manual
