Panasonic CZ-RWS3 User manual

Installation Instructions

Infrared Remote Controller

Model No. CZ-RWS3

Safety Precautions ...................................... 2

Supplied accessories.................................. 4

Speciﬁcations .............................................. 4

Installation Precautions.............................. 5

Before Starting............................................. 6

When using the wall mounted type

indoor unit.................................................... 6

Miscellaneous Settings............................... 7

Auto Address ............................................... 8

H0921-0

Contents

English

Read through the Installation Instructions before you proceed

with the installation.

In particular, you will need to read under the “Safety

Precautions” on page 2.

2(EN)

Safety Precautions

We assume no responsibility for accidents

or damages resulting from methods other

than those described in the installation

instructions or methods without using

speciﬁed parts.

Malfunctions that occurred due to the

unauthorised installation methods are not

covered by the product warranty.

 Read the installation instructions supplied

with indoor units as well.

 After the installation is complete,

perform test operation to conﬁrm that no

abnormality is present.

 When relocating or repairing this

controller, provide the Installation

Instructions to the servicing personnel.

 Do not clean inside the controller by

users. Engage authorised dealer or

specialist for cleaning.

WARNING

This symbol refers to a hazard or unsafe

practice which can result in severe personal

injury or death.

CAUTION

This symbol refers to a hazard or unsafe

practice which can result in personal injury or

product or property damage.

WARNING

 Turn oﬀthe circuit breaker of

the units before installation.

 Select an installation location

which is rigid and strong

enough to support or hold

the controller, and select a

location for easy maintenance.

 This controller must not be

modiﬁed or disassembled

under any circumstances.

Modiﬁed or disassembled

controller may cause ﬁre,

electric shock or injury.

Read before installation

This controller must be installed by the sales dealer or installer.

These instructions are all you need for most installation sites and maintenance conditions.

If you require help for a special problem, contact our sales/service outlet or your certiﬁed

dealer for additional instructions.

(EN)

CAUTION

 Do not allow infants and small

children to prevent them from

accidentally swallowing the

batteries.

 Do not use the controller at

the following locations.

• Location where

condensation occurs

• Location where ﬂammable

gases, etc. may leak

• Location where corrosive

gases, etc. may leak

• Location with lots of water

or oil droplets (including

machine oil)

• Location where there

is a machine producing

electromagnetic radiation

• Location where droplets of

organic solvents spread

• Location where acidic or

alkaline solutions or special

sprays are frequently used

 Do not wash with water.

 Do not operate with wet

hands.

 Do not drop or throw. (It may

cause malfunction.)

 Do not insert the battery the

wrong terminals (+ and -). (It

may cause electrolyte leakage

and may cause a ﬁre.)

NOTICE The English text is the original instructions. Other languages are translation of

the original instructions.

4(EN)

Supplied accessories

< >: Number of pieces

Remote Control Holder

Screw M4×15.5

LR03 Size Battery (for test)

Operating Instructions

Installation Instructions

Instructions Disc

<1>

<2>

<1>

Speciﬁcations

Model No. CZ-RWS3

Dimensions (H) 165 mm × (W) 59 mm × (D) 22 mm

Weight 100 g (Batteries and remote control holder are not included)

Temperature/Humidity

range

0 ˚C to 40 ˚C / 20 % to 80 % (no condensation)

*Indoor use only

Power Source Two LR03 size batteries

(EN)

Installation Precautions

The controller uses a very weak infrared light for its signal, which can result in the signal not being

received because of the following inﬂuences, so take care in where the indoor unit is installed.

• Inverter or rapid-start type ﬂuorescent lights (Models without glow lamps)

• Plasma display or LCD televisions

• Direct sunlight or other sources of bright light

Install in a location that does not interfere the operation

• You cannot operate if the distance between the remote controller and the receiver is greater than

that signals can travel.

• Make sure nothing is between the remote controller and the receiver that could block the signal.

• Make sure the air conditioner works with the remote controller in the location where it will be

installed.

Avoid the following locations for installation.

• Under direct sunlight

• Location near heat source

• Location where the controller will be splashed with water or aﬀected by dampness or humidity

• Uneven surface

• Location that is subject to excessive vibration or physical impacts. (Fixing screws may come oﬀ,

and the controller may drop.)

• Location with large amount of oil smoke or steam (such as kitchen or machine factory)

Install the controller vertically to the ﬂoor.

Install the controller at a location with suitable temperature and humidity for using.

Do not install controller at the locations with the equipment (medical equipment, etc.) which

generates the high-frequency emissions. (It may interfere with the equipment and may cause

accidents due to malfunction.)

Install at least 1 m away from TV, radio, PC. etc. (To prevent fuzzy images or noise)

6(EN)

Before Starting

Install this controller referring to the “Operating Instructions”.

(1) Insert the batteries. (Installing Batteries)

(2) Set the current time. (Setting the Current Time)

(3) Install the remote control holder. (Using the Remote Controller)

(4) Perform the pairing address setting,if required. (Paring Addresses)

When using the wall mounted type

indoor unit

Note

Also refer to the installation instructions supplied with the wall mounted type indoor unit.

When using the infrared remote controller and the wired remote controller in combination, set the

wired remote controller to [Main].

When only using the infrared remote controller, it is necessary to set the selector switch on the

indoor unit circuit board (S011 or SW502) from “OFF” to “ON”.

When group-controlling the multiple wall mounted type indoor units, set “OFF” to “ON” on only one

unit.

(Example)

Grille

Cover

SW502

(EN)

Miscellaneous Settings

• These settings are saved in nonvolatile memory in the remote controller, so evenwhen its batteries

are changed, the settings do not have to be made again.

• Furthermore, making changes to these settings may cause actual operation to deviate from what is

printed in the Operating Instructions, so be sure to fully explain this to the customer.

• Do not change any settings other than those items in table below.

1. Press , and at the same time for 4 seconds or longer

when the controller is stopped (displaying the current time only).

• “ ” starts blinking and the setting screen is displayed.

Setting data

Item number

2. Press / to select item number,

press / to select setting data,

and press .

3. Press .

Setting item Setting data Factory

setting Check

1Operation Mode*1

2Flap Display

3Select Fan Speed

5Clock Display 00: 24-hour

4Temperature Display 00: °C 01: °F 00: °C

00:

5 levels

(Cool in 5 levels) +

Swing + Stop

00: Speed 5

(1 to 5, Auto)

6Ventilation Fan Setting*2 00: Off 01: On 00: Off

18 Energy Saving Setting*2 01: On

19 ECONAVI Setting*2 01: On

20 nanoeTM X Setting*2

*1 Set to [02: / / ] or [03: / ] if you are using the unit only for cooling.

*2 Press the function setting button for 4 seconds or longer while current time is displayed to switch the function On/Off.

01: On

703Cool Temp Max

881

930

10 61

11 03

12 81

13 72

14 71

00:

5 levels (Cool in 5 levels) + Swing + Stop

01:

5 levels (Cool in 3 levels) + Swing + Stop

02:

5 levels (Cool in 3 levels) + Swing

03: /

04: / / /

05: / /

03: Swing

04: No switchable function

00: 5 levels (1 to 5, Auto)

01:

3 levels (Low (1), Medium (3), High (5), Auto)

02:

3 levels (Low (1), Medium (3), High (5))

03: Low (1), Medium (3)

04: No switchable function

00: / / / /

01: / / /

02: / /

03: /

04: / / /

05: / /

00: 24-hour 01: AM/PM

Cool Temp Min

Heat Temp Max

Heat Temp Min

Dry Temp Max

Dry Temp Min

Auto Temp Max

Auto Temp Min

5 – 35°C

00: Off 01: On

00: Off

01: On

Item

Number

Note

Make sure to ﬁll the setting status in the check column after making changes to these settings.

8(EN)

Auto Address

Set the Auto Address for each O/D unit no. (outdoor

unit number)

Select the O/D unit no. for Auto Address.

1. Press

ADR

for 4 seconds or longer.

• " " starts blinking and the setting screen is

displayed.

2. Press to select the unit

number (O/D unit no.) from 1 to 30.

3. Press to set the Auto Address.

4. Press to check the Auto Address

status.

(Refer to the following table for the Auto Address

status.)

• Proceed to step 5 when the status is

"Completion" or "Error".

• If "Running" keeps for 10 minutes or longer,

check the unit number.

Address

Auto Address

Status

Buzzer of the

receiver

Indication lamp on the receiver

OPERATION TIMER STANDBY

Running 2 times ◎◎◎

Completion 1 time - - -

Error 5 times ●●◎

●: OFF, ○: ON (Illuminated), ◎Blinking (0.5 seconds interval)

5. Press for 4 seconds or longer to exit the Auto Address setting.

• Auto Address setting is canceled while running or error occurring. Set the Auto Address again

after resolve the error cause if an error occurs.

Attention

• Set Auto address after all units are turned on and 90 seconds or more have passed.

• Operate the units after Auto address is set and 90 seconds or more have passed.

Panasonic Corporation

http://www.panasonic.com

Other manuals for CZ-RWS3

Table of contents

Other Panasonic Controllers manuals

Panasonic

Panasonic CZ-256ESMC1U User manual

Panasonic

Panasonic FP2-PP2T User manual

Panasonic

Panasonic FP7 Series User manual

Panasonic

Panasonic AFPX-COM5 User manual

Panasonic

Panasonic EYFLA7AR Operating instructions

Panasonic

Panasonic FP0 Series User manual

Panasonic

Panasonic FP7 Series Parts list manual

Panasonic

Panasonic CZ-TACG1 User manual

Panasonic

Panasonic CZ-256ESMC3 User manual

Panasonic

Panasonic DPH-L100 User manual

Panasonic

Panasonic AWRP605P - MULTI FUNCTION CONTROLLER User manual

Panasonic

Panasonic FP-M Hardware User manual

Panasonic

Panasonic CZ-RD517C User manual

Panasonic

Panasonic AW-HHD100E User manual

Panasonic

Panasonic AFP7CPS4E User manual

Panasonic

Panasonic FP2 Series User manual

Panasonic

Panasonic WVCU950 - CONTROLLER - ADDENDUM User manual

Panasonic

Panasonic CZ-TACG1 User manual

Panasonic

Panasonic FP-X0 L14R User manual

Panasonic

Panasonic CZ-CAPE2 Quick guide

Panasonic

Panasonic FMU User manual

Panasonic

Panasonic AFP7PSA1 User manual

Panasonic

Panasonic GM1 Series User manual

Panasonic

Panasonic FY-EB90S1 Technical manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide

KUHN

KUHN TKS user manual