Panasonic AW-RP50 User manual

★ AW-RP50 controller can control up to five AW-HE40 cameras via the serial connection.

1. Connection

Connect one of AW-RP50 “T PAN/TILT HEAD” ports [1] – [5] and AW-HE40 “RS-422” port using a LAN cable

(Category 5 or higher, Straight cable, Up to 1,000m).

2. Setting Up AW-RP50

Example: Connection to AW-RP50 “T PAN/TILT HEAD” port [1]

① Press MENU button. – (Fig.3-A)

② Press [10] SYSTEM button. – (Fig.3-B) * “[1] CAMERA CTL” will be displayed on the LCD Panel. – (Fig.4)

* If it is not displayed, turn F1 dial – (Fig.3-C) to make “[1] CAMERA CTL” appear.

③ While “[1] CAMERA CTL” is displayed on the LCD, press F1 dial.

* “[1] CAM1” will be displayed on the upper half, and the connection method (default: [NoAsign]) on the lower

half of the LCD Panel. – (Fig.4)

④ Turn F2 dial – (Fig.3-D) to select [Serial], and then press F2 dial to determine the setting.

<Note>

・ Camera numbers CAM1 – CAM5 correspond to “T PAN/TILT HEAD” ports [1] – [5] on the Rear Panel,

respectively.

For example, if “T PAN/TILT HEAD” port [5] is used for serial connection, set [1] CAMERA CTL > 5. CAM5

to [Serial].

③Press F1

(LAN Cable)

Controlling AW-HE40 with AW-RP50 (vi Seri l Connection)

(Figure 4: LCD Panel)

（A）

（B）

（C）

（D）

(Figure 3: AW-RP50 Control Panel)

(Figure 1: AW-RP50 Rear Panel) (Figure 2: AW-HE40 Rear Panel)

［1］CAMERA CTL

①MENU N => ②Select [10]

④Turn F2 to select

=> Press F2 to set

1．CAM1

NoAsign

1．CAM1

Seri l

・ The [Serial] setting for serial connection cannot be set for camera numbers CAM6 – CAM100.

3. Turning On AW-HE40

★ After the setting-up is completed, LED button 1 at AW-RP50 CAMERA STATUS / SELECTI N Area – (Fig.5) lights

up according to the camera’s power status. If the camera is in STANDBY mode (power FF: factory default), it

lights up in orange. If in P WER N mode (power N), it lights up in green.

★ When the camera is in STANBY mode, follow the procedure below to turn on the camera.

Example: Switching over to P WER N mode (power N) on AW-HE40 connected to CAM1

① Hold down LED button 1 at CAMERA STATUS/SELECTI N. – (Fig.6-A)

* While the button is held down, the selected camera and its power status will be displayed on the LCD Panel. –

(Fig.7)

② Keeping the button held down, turn F2 dial – (Fig.6-B) to select “ N”. Then press F2 dial to determine it.

* By this operation, AW-HE40 will be switched over to P WER N mode after its default setting motion.

(The status lamp will light up in green and the LED on AW-RP50 will also light up in green.)

* In P WER N mode, if you follow the same procedure and select [P WER: FF], AW-HE40 will be switched

over to STANBY mode.

CAM1＜AW-HE40 ＞

POWER

：

OFF

CAM1＜AW-HE40 ＞

POWER

：

“C

AM1”

is held down

Select “ N” => Press F2 to determine

Turn F2

After setting up, this lights up

according to the camera’s

power status.

* If it does not light up, please check the following points.

（A）

(Figure 6: AW-RP50 Control Panel)

(Figure 7: LCD Panel)

（B）

① Check the connection state of LAN cable or whether you are using a cable that meets the specifications.

② Check that the LAN cable is connected to “RS-422 port”, not to “LAN port”.

③ Double-check that there is no error in setting up the connection.

(Figure 5: AW-RP50 CAMERA STATUS/SELECTI N Area)

Other manuals for AW-RP50

Table of contents

Other Panasonic Controllers manuals

Panasonic

Panasonic CZ-ANC3 User manual

Panasonic

Panasonic SL-GU1-D User manual

Panasonic

Panasonic FP-I4C User manual

Panasonic

Panasonic AW-RP60G User manual

Panasonic

Panasonic CZ-RD516C-1 User manual

Panasonic

Panasonic GM1 Series User manual

Panasonic

Panasonic WRKT4504E Series User manual

Panasonic

Panasonic FP0H Series User manual

Panasonic

Panasonic FP2-PP2T User manual

Panasonic

Panasonic FP-XH Series User manual

Panasonic

Panasonic CZ-256ESMC3 Instruction manual

Panasonic

Panasonic WV-CU980/G User manual

Panasonic

Panasonic PT-F100 User manual

Panasonic

Panasonic CZ-256ESMC2U User manual

Panasonic

Panasonic FP E Series User manual

Panasonic

Panasonic HG-SC User manual

Panasonic

Panasonic Programmable Controllers FP-X Series User manual

Panasonic

Panasonic FP0 Series User manual

Panasonic

Panasonic AW-RP605AN User manual

Panasonic

Panasonic FP0-TC4 User manual

Panasonic

Panasonic FP-X0 L14R User manual

Panasonic

Panasonic KT4R Use and care manual

Panasonic

Panasonic FP7 Series User manual

Panasonic

Panasonic FP7 Series User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide

KUHN

KUHN TKS user manual