Panasonic FP2 Series User manual

PROGRAMMABLE CONTROLLER

FP2 Multi-wire Link Unit

Technical Manual

ARCT1F302E-2

2008.11

Safety Precautions

Observe the following notices to ensure personal safety or to prevent accidents.

To ensure that you use this product correctly, read this User’s Manual thoroughly before use.

Make sure that you fully understand the product and information on safety.

This manual uses two safety flags to indicate different levels of danger.

WARNING

If critical situations that could lead to user’s death or serious injury is assumed by

mishandling of the product.

-Always take precautions to ensure the overall safety of your system, so that the whole system

remains safe in the event of failure of this product or other external factor.

-Do not use this product in areas with inflammable gas. It could lead to an explosion.

-Exposing this product to excessive heat or open flames could cause damage to the lithium battery

or other electronic parts.

CAUTION

If critical situations that could lead to user’s injury or only property damage is assumed

by mishandling of the product.

-To prevent excessive exothermic heat or smoke generation, use this product at the values less than

the maximum of the characteristics and performance that are assured in these specifications.

-Do not dismantle or remodel the product. It could cause excessive exothermic heat or smoke

generation.

-Do not touch the terminal while turning on electricity. It could lead to an electric shock.

-Use the external devices to function the emergency stop and interlock circuit.

-Connect the wires or connectors securely.

The loose connection could cause excessive exothermic heat or smoke generation.

-Do not allow foreign matters such as liquid, flammable materials, metals to go into the inside of the

product. It could cause excessive exothermic heat or smoke generation.

-Do not undertake construction (such as connection and disconnection) while the power supply is on.

It could lead to an electric shock.

-This manual and its contents are copyrighted.

-You may not copy this manual,in whole or part,without written consent of PanasonicElectric

Works.,Ltd.

-Windows and Windows NT are registered trademarks of Microsoft Corporation in the

United States and/or other countries.

-All other company names and product names are trademarks or registered

trademarks of their respective owners.

-Matsushita Electric Works,Ltd. pursues a policy of continuous improvement of the

Design and performance of its products, therefore,we reserve the right to change the manual/

product without notice.

BNTN

Table of Contents FP2 Multi-wire Link Unit

Table of Contents

Before You Start v......................................................

Chapter 1 General Specifications

1.1 How the Multi-wire Link Unit Works 1 - 3.................................

1.1.1 MEWNET-W Mode 1 - 4.........................................

1.1.2 MEWNET-W2 Mode 1 - 5........................................

1.1.3 MEWNET-F Mode 1 - 6.........................................

1.2 Specifications 1 - 8....................................................

1.2.1 General Specifications 1 - 8......................................

1.2.2 Transmission Specifications 1 - 9.................................

1.2.3 Performance Specifications 1 - 10.................................

1.2.3.1 W and W2 Modes 1 - 10................................

1.2.3.2 F Mode 1 - 11.........................................

1.2.4 Transmission Cable Specifications 1 - 12...........................

1.3 Restrictions When Combinations Are Used 1 - 14..........................

1.3.1 Restrictions on the CPU 1 - 14....................................

1.3.2 Restrictions on the Installation Position 1 - 14.......................

1.3.3 Restrictions on the Number of Units that can be Installed 1 - 15.......

1.4 Confirming the Design Contents 1 - 16...................................

1.4.1 Confirming the Current Consumption 1 - 16.........................

1.4.2 Confirming I/O Allocations 1 - 16..................................

1.4.3 Confirmation When Multiple Units are Installed 1 - 17................

Chapter 2 Parts and Its Functions

2.1 Parts Terminology 2 - 3................................................

2.1.1 Status Indicator LEDs 2 - 5.......................................

2.1.2 Slave Station Number Display Selector Switch 2 - 6.................

2.2 Switch Settings 2 - 7...................................................

2.2.1 Station Number Selector 2 - 7....................................

2.2.2 Mode Selector Switches (1) 2 - 8..................................

2.2.3 Mode Selector Switches (2) 2 - 9..................................

Chapter 3 Wiring

3.1 Wiring 3 - 3..........................................................

3.1.1 Transmission Cable Wiring 3 - 3..................................

3.1.2 Crimp Terminal Specifications 3 - 4................................

Table of Contents

FP2 Multi-wire Link Unit

iii

Chapter 4 MEWNET-W Mode

4.1 W Mode Functions 4 - 3................................................

4.1.1 PC Link Function 4 - 3...........................................

4.1.2 Data Transfer Function 4 - 3......................................

4.1.3 Remote Programming Function 4 - 3...............................

4.2 PC Link 4 - 4.........................................................

4.2.1 Preparing to Use PC Link 4 - 4....................................

4.2.2 Link Area Allocations 4 - 4.......................................

4.2.3 Link Area Allocation Example 4 - 5................................

4.2.4 Sample PC Link Program 4 - 8....................................

4.2.5 Precautions When Allocating Link Areas 4 - 10......................

Appendix A What to Check If a Problem Occurs

A.1 If the CPU ERROR LED Lights 5 - 3.....................................

A.2 Confirming the Mode Being Used 5 - 4...................................

A.3 What to Check When the ERR LED Is Lighted or Blinking 5 - 5..............

A.4 What to Do If a Transmission Error Occurs 5 - 6...........................

Appendix B Dimensions

Index i-1................................................................

Record of changes R-1...............................................

Before You Start FP2 Multi-wire Link Unit

Before You Start

CPU Versions Supported

This unit supports CPU Ver. 1.05 and subsequent versions. Confirm the version on the

side panel seal on the CPU, or on the [STATUS DISPLAY] in the [MONITOR] menu of

the NPST-GR.

Selecting Cables

Cables which can be used with this unit vary depending on the mode being used. For

information on cable connections, refer to section 3.1.

Mode Cables used

MEWNET-W

MEWNET-W2 Twisted pair cable

MEWNET-F Twisted pair cable, VCTF cable

About Selecting MEWNET-W2

In order to use the FP2 Multi-wire link unit in MEWNET-2 mode, the user must write

a program on a level of about 300 steps. Proceed only after carefully going over the

specifications.

Please inquire about more detailed materials regarding MEWNET-W2.

Before You Start

FP2 Multi-wire Link Unit

Reference Manuals

The following reference manuals are available for use with this unit, and should be

used in conjunction with this manual.

Manual name Manual number Description

FP2 Hardware

manual ARCT1F298E This introduces the hardware configuration, wiring

methods, I/O allocation, maintenance methods, and

other information pertaining to the FP2 series.

FP3/FP5 W TYPE

(WIRE) LINK

SYSTEM Manual ACG-M0032

This introduces the hardware configuration, wiring

methods, I/O allocation, maintenance methods, and

other information pertaining to the MEWNET-W.

Refer to this manual when using the MEWNET-W

mode.

FP3/FP5

REMOTE I/O

SYSTEM Manual ACG-M0028

This introduces the hardware configuration, wiring

methods, I/O allocation, maintenance methods, and

other information pertaining to the MEWNET-F.

Refer to this manual when using the MEWNET-F

mode.

Chapter 1

General Specifications

1.1 How the Multi-wire Link Unit Works 1 - 3........

1.1.1 MEWNET-W Mode 1 - 4...............

1.1.2 MEWNET-W2 Mode 1 - 5..............

1.1.3 MEWNET-F Mode 1 - 6................

1.2 Specifications 1 - 8............................

1.2.1 General Specifications 1 - 8............

1.2.2 Transmission Specifications 1 - 9........

1.2.3 Performance Specifications 1 - 10.......

1.2.3.1 W and W2 Modes 1 - 10........

1.2.3.2 F Mode 1 - 11.................

1.2.4 Transmission Cable Specifications 1 - 12.

1.3 Restrictions When Combinations Are Used 1 - 14.

1.3.1 Restrictions on the CPU 1 - 14..........

1.3.2 Restrictions on the Installation

Position 1 - 14........................

1.3.3 Restrictions on the Number of Units

that can be Installed 1 - 15.............

1.4 Confirming the Design Contents 1 - 16...........

1.4.1 Confirming the Current

Consumption 1 - 16...................

1.4.2 Confirming I/O Allocations 1 - 16........

1.4.3 Confirmation When Multiple Units are

Installed 1 - 17........................

General Specifications FP2 Multi-wire Link Unit

1-2

Other manuals for FP2 Series

This manual suits for next models

Table of contents

Other Panasonic Controllers manuals

Panasonic

Panasonic WV-CU980/G User manual

Panasonic

Panasonic SL-VGU1-C User manual

Panasonic

Panasonic S-Link FP2 User manual

Panasonic

Panasonic FP7 Series User manual

Panasonic

Panasonic FV-SW20VEC1 User manual

Panasonic

Panasonic FP3 User manual

Panasonic

Panasonic AWRP605 - CCU & PAN/TILT CONTR User manual

Panasonic

Panasonic CZ-TACG1 User manual

Panasonic

Panasonic FP-XH Series User manual

Panasonic

Panasonic CZ-ANC2 User manual

Panasonic

Panasonic AFPXHEAD4 User manual

Panasonic

Panasonic AW-RP120G User manual

Panasonic

Panasonic WVCU550C - SYSTEM CONTROLLER UNIT User manual

Panasonic

Panasonic TY-TP10W User manual

Panasonic

Panasonic AWRP605P - MULTI FUNCTION CONTROLLER User manual

Panasonic

Panasonic WV-CU101 User manual

Panasonic

Panasonic FP Web-Server2 User manual

Panasonic

Panasonic AFPX-COM5 User manual

Panasonic

Panasonic AFP7CPS4E User manual

Panasonic

Panasonic SL-VGU1-EC User manual

Panasonic

Panasonic CZ-RD516C-1 User manual

Panasonic

Panasonic fp2/fp2sh User manual

Panasonic

Panasonic CZ-RD517C User manual

Panasonic

Panasonic AF7CPS Series User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide

KUHN

KUHN TKS user manual