Omcan HSB-300 Technical manual

- 1 -

Ⅰ

Notice

•

the power must be complied with electric requirements on the label rating, it will cause

the serious trouble of the fire or the machine if improperly use.

• The machine must be earthed when using, it is dangerous to get an electric shock if not

ground or not reliable to be grounded.

• Please turn off all switch and unplug when Emergency happen.

• The hand or other part of body not allow to enter workspace when the machine open, or

will hurt you.

• The machine should be repaired by manufacturer or agent if the machine fault.

• We are not Responsible for hurting or equipment fault as self amending machine.

• When the electric wire damage, must instead of it.

• The electric wire must be used special soft wire, buy it from manufacturer or repair

department.

• The machine can not be wash by water, the machine is not the waterproof structure, it

will cause get an electric shock and damage the mechanical departments and electric

parts.

• Please turn off all switches when not operate and unplug.

• Please stop operate and unplug when workman clean the machine.

• Must to stop the machine operate when find the machine operate unusually.

• Often to check blade-cover, table loading meat, slice and other parts whether tight or

damage.

• Can not cut the frozen meat below the temperature of -6℃.

• Please attach the manual operation when resell the machine.

• Please contact with our when damage or lose the manual operation.

• Please contact us when you meet other items which not detail in the manual operation.

Ground terminal must be ground before the slicer is fixed.

Avoid resulting in personal server injury due to leakage.

Slicer operates automatically; keep hand clear, Failure to comply may result

inpersonal server injury due to leakage.

Clean and change blade of slicer, be careful of blade-edge hurt your finger.

Ⅱ. Main Technical Specifications

Model: HSB-300 HBS-250 HBS-220

Voltage 220V 50HZ/110V 60HZ 220V 50HZ/110V 60HZ 220V50HZ/110V 60HZ

Power 250W 120W 110W

Slicing thickness 0.2~15MM 0.2~15MM 0.2~15MM

Blade diameter 300MM 250MM 220MM

Max slicing width 220MM 180MM 160MM

Weight 25KGS 20KGS 17KGS

Measurement 597X520X495MM 537X460X400MM 498X435X380MM

- 2 -

Ⅲ.

Machine instruction and part name:

Ⅳ. Operation

1. The machine should be installed on a work surface that has sufficient stability and

strength to support the weight of the machine.

Make sure that the line voltage of your main power source matches the rated voltage

of the machine .

Turn the switch on and let the machine race about 2-3 minutes look if the machine

works well.

Turn the switch on, the pilot lamp of the power button is lighting, the lade rotate on

the opposite way of watch hands.

Adjust the slice thickness by turning the slice thickness regulator on the opposite

way of watch hands. And turn the fixing positioner knob ib the way of watch hands.

Make the fixing positioner head get in touch with the plate.

Pushing the product carriage forward and back over the blade with a continuous

motion, using the product pusher handle and the pusher knob.

After slicing the desired amount of the zero position. Turn the fixing positioner knob

and let the fixing positioner head back to the original position.

8. You can now move away the slices and the product.

Ⅴ. Cleaning:

1. Always turn off and unplug the machine before cleaning, and make sure to turn the

slice thickness regulator to zero position.

Never use any chemical or abrasive products. Do not use a brush or any other type

of utensils instrument, which could damage the different piece of the slicer.

Use a damp cloth in detergent to clean the machine, thin and dry. Make sure to clean

the machine completely every day.

Removing the blade cover away from the blade when cleaning, and clean the

product carriage too.

Warnings for blade cleaning:

a. Wear a safety glove for making this operation;

Do not touch the edge of the blade;

This is a dangerous operation be careful.

6. You ought to race the machine 5 minutes after cleaning.

Attention: Do not wash the machine by water directly.

Ⅵ. Maintenance:

1. Blade rustproof:

a. Dry the blade with fry cloth after work;

Spread the cooking oil on the edge of the blade with dry cloth;

Sharp the blade every day to prevent rust.

2. Guide lubrication:

Sharpener 6. Slicer thickness regulator

2. Blade cover 7. Power button

3.Active pusher 8. Plate

4. Carriage 9. Slicer

5. Product pusher handle

- 3 -

a. Push the carriage to one side, and clean the grease dirt of the guide with dry

cloth;

Smear the guide surface with grease by finger, well spread and lubricate;

It is suitable to lubricate the guide every week.

3. Pusher axle lubrication:

a. Clean the pusher axle with dry cloth first;

Put the cooking oil on the both of the axles and pull the pusher up and down to

make the oil well spread and the pusher work well

It is suitable to lubricate the axle every day.

4. Sharpener lubrication

a. Clean the sharpener axle before sharpening;

Put the cooking oil on the both of the axles;

Turn around and slide the axle until the axles work well.

5. Localizing head lubrication:

a. Turn the fixing positioner on the opposite way of watch hands to the max length;

Clean the localizing head and put the cooking oil on;

The trun the fixing positioner back to the original position;

It is suitable to lubricate it every week and do not spread too much oil.

Ⅶ. Blade Sharpening:

1. You ought to sharpen the blade when the slice thickness not even or the slices

broken not piece.

Clean the edge of blade before sharpening.

Pull the sharpener out and lubricate the sharpener axles as it works well.

Pull the sharpener out and turn 180º, press the right side stone down by finger then

put the sharpener to the working position.

Make sure that the surface of stone is nesting closely to the surface of edge. If not,

please adjust it.

Turn the power on and the blade work 1-2 minutes, stop the machine look if the

blade is sharpened well, if not, continuous.

7. Press the left side stone down and make sure the surface of stone is nesting

closely to the surface of blade, then sharpen 3 seconds to remove the burr.

8. Put the sharpener back to the original position after work.

9. Always keep the stone clean as the stones work well.

10.Do not make your eyes look right to the way that the stone rotate in order to the hurt

from the piece of the stone.

ILLUSTRATION

- 4 -

OPERATION INSTRUCTION FOR MEAT SLICER

Table of contents

Popular Kitchen Appliance manuals by other brands

Tayama

Tayama TYG-35AF instruction manual

AEG

AEG 43172V-MN user manual

REBER

REBER Professional 40 Use and maintenance

North American

North American BB12482G / TR-F-04-B-NCT-1 Assembly and operating instructions

Presto

Presto fountain popper instruction manual

Westmark

Westmark 1035 2260 operating instructions

Zanussi

Zanussi ZCG64396XA user manual

HOFFEN

HOFFEN SM-9302M instruction manual

Philips

Philips HD3133 user manual

Ronco

Ronco Beef Jerky User guide and recipes

Hendi

Hendi 470411 user manual

Livoo

Livoo MEN386 user manual

Vogue

Vogue D446 instruction manual

croydon

croydon WR-10313-700 instruction manual

ADE

ADE AUTOMATIC-L operating instructions

Chefman

Chefman RJ43-SQ Series user guide

Vacmaster

Vacmaster VP680 user guide

Jetmaster

Jetmaster 900HG operating instructions