Hideaway Soft Close User manual
Step 1 - Unpack Hideaway Bin
Remove all polystyrene.•
Remove the bucket/s.•
Please leave the Glad sample pack and instructions inside the bucket for the homeowner.•
(NZ only)
Step 2 - Remove the door bracket (g 2 & 3)
Placethemountingpanelupsidedownonaatsurfacewiththerunnersfacingupwards.•
Fully extend the runners• . It is critically important that you extend as far as they will open.
Undo the nut on either side of the door bracket (these nuts attach the door bracket to•
the collar).
Remove door bracket - set nuts aside in a safe place (see Fig 2).•
NOTE: VERY IMPORTANT - do not remove the collar from the runners or the runners from the•
mounting panel.
Step 3 - Remove the friction-tted lid from mounting panel
(g 4a, 4b & 4c)
Mountingpanelshouldstillbeupsidedownonaatsurfacewiththerunnersfacingupwards.•
Toremovethefriction-ttedlid-pushrmlydownonthelidatthebackoftheunit.•
Pushrmly,distributingpressuretobothsidesoflidtoensurethelidclearsthehookslocatedon•
the left and right hand sides of the mounting panel.
Simultaneously,pullthefriction-ttedlidforwardsuntilitpullsclearofthemountingpanel.•
Pullthefoampadclearofthemountingpanel.Setaside,leavingtheplasticcoveron.•
Step 4 - Top mounting bins only: Install your bins within your
cupboard/carcass
Positionthemountingpanel(nowclearofrunnerinnerandcollaraswellasfriction-ttedlidand•
foampad)inside,beneathyourcarcass/shelf.
Position within the centre of the carcass and ensure the front of the mounting panel is sitting•
ushwiththefrontofthecarcass.Mountingpointsarelocatedonthetopofthemountingpanel
forxing.Securethemountingpanelintoplacewiththe16mmSurexscrewsprovided.
Any additional mounting points added will null and void warranty.
Step 5 - Install your bin within your cupboard / carcass
YourunithassidemountingpointsasshowninFig1.Ifsidemounting,theinternalspaceofthe•
cabinet must be within the advertised width.
Thesidemountingpointsaretobesecuredwiththe16mmSurexscrewsandwashersprovided.•
Step 6 - Reinstall the friction-tted lid and foam into mounting panel
Restthefoamontopofthefriction-ttedlid-theatsideofthefriction-ttedlidshouldbetowards•
the ground with the folds facing upwards.
Slidethefriction-ttedlidandfoaminsidethemountingpanel,stoppingjustbeforetherear•
hooks.(Note:thelargefoldonthefriction-ttedlidsitsatthefrontoftheunit,andtherearofthe
lid has the slots which reconnect with the hooks located on the mounting panel at the rear).
Simultaneously,withonehand,pushrmlyuponthebackofthefriction-ttedlid,pushthelidabove•
thehooksanddropintolocation.Whilstthisishappening,withtheotherhandpushthefrontof
the lid upwards to ensure it rests on the metal support (located at the front of the mounting panel -
g4c).
Thelidshouldmoveupanddownslightlywithease,indicatingcorrectinstallation.•
Step 6 - Reattach the door bracket
Extend the runners once again.•
Align the door bracket to the collar and lightly tighten in place using the nuts provided.•
The Hideaway®Soft Close Installation Instructions
Fig 2
Door bracket and collar detached
Fig 1
Collar
Door
Bracket
Door Bracket
Friction-
ttedlid
Liner
holder
Runners
Fig 3
Door bracket and collar attached
Fig 4a
Pushrmlyonthebackoftheunit
to ensure the lid clears the hooks
located on the right and left hand
sides of mounting panel
Mounting
panel
Top and/or side
mounting points
Buckets
Questions?
NEW ZEALAND
Phone 094267456 Email [email protected] Web www.hideawaybins.co.nz
AUSTRALIA
NOTE:Lightlytightennutstoallowxingofdoorfront.•
Step 7 - Fix cabinet fascia to door bracket of bin
Placea4mmselftappingscrewintothecentreholeofthedoorbracket-ensurethepointofthe•
screw is only protruding approx 3mm.
Withthebinclosedfully,alignthefrontfasciaofthecupboardagainstthedoorbracket.Asmallhit•
with your hand to the location of the screw will help provide a drilling indication.
Liecabinetfasciaonaatsurfacewiththeinternalpartofthedoorfacingupwards.Usingthe•
drillingmarkmadetothecentrepointonthecabinetfascia,drillaholetoholdcentrescrew(if
requiredforeaseofinstallation,removethedoorbracketfromtheunitonceagain.Attachthedoor
bracket with the centre screw to the cabinet fascia and then reattach the door bracket to the collar
of the bin once again.)
Place the cabinet fascia against the door bracket and tighten the centre screw. Check the•
positioning and align.
Proceedtomarking,screwingandtighteningtheremainingscrews.Verticalandhorizontal•
adjustmentisprovidedonthedoorbracket.
Toadjusttheangleofyourkitchenfascia:loosenortightenthenutsonthedoorbracketuntil•
desiredangleisachieved.Thecentrenutprovidespivot.Oncethedesiredangleisachieved,
rmlytightenallnutsonthedoorbracket.
IMPORTANT INSTALLATION INFORMATION: At all stages of the
installation ensure the spring carrier on the runner is engaged.
Before you close the unit ensure the spring carrier is loaded on your soft close runner. Failure to
do so will cause damage to your runners. In all cases replacement is required.
Figure5a-demonstratesthespringcarrierintheengagedposition.Thisisthecorrectpositioning
and the bin is ready to be closed and used.
Figure5b-demonstratesthespringcarrierinanunengagedposition.Thisisincorrectpositioning
andwillcausedamagetoyourrunners.Tomoveintoengagedposition,movethewhitespring
carrier along its runner until it clicks into location demonstrated by arrow in diagram below.
Figure6-demonstratesadamagedrunner.Ifyoudonotcheckyourrunnersandensureatall
stages the spring carriers are in an engaged position you will bend the white guiding arm on the
shock absorber. Once this has happened you have damaged your runners and will require new
ones.Thesupplyofnewrunners,withoutadditionalcost,isatthediscretionofKitchenKingLtd
in all cases.
Step 8 - Place bin buckets into checkouts on collar
Fully extend the runners.•
Place bucket/s into the checkouts provided on the collar. The back bucket must sit over the lip on•
the back of the frame. If the bucket/s do not sit within these checkouts the unit will not close
properly.
Trade• - please leave the Glad sample pack inside the bucket.
Homeowner• –youwillndaGladsamplepackinthebaseofyourbucket.SlidetheGladKitchen
Tidy Bag into your bucket/s ensuring the bag will not interfere with the tracks. (NZ only)
Place liner holders on top of bucket/s.•
Installation complete!
Fig 5a Runner engaged - correct
Fig 4b
Fig 5b Runner unengaged - incorrect
Fig 6 Damaged runner - requires
replacement
NZPatApplnNo.585372
Lid coming
free of hook
Hook
Metal support
Fig 4c
The unit should look like this
withthefriction-ttedlidand
door bracket removed
Other Hideaway Kitchen Appliance manuals
Popular Kitchen Appliance manuals by other brands
Tayama
Tayama TYG-35AF instruction manual
AEG
AEG 43172V-MN user manual
REBER
REBER Professional 40 Use and maintenance
North American
North American BB12482G / TR-F-04-B-NCT-1 Assembly and operating instructions
Presto
Presto fountain popper instruction manual
Westmark
Westmark 1035 2260 operating instructions
