Grinder CM100M User manual
Manual of Multi-functional Mill CM100M
Beijing Grinder Instrument Co., Ltd. Tel：010-82363430 Fax：010-82363435 www.grindertech.cn
1
CONTENT
1.0 Notes on the Manual................................................................................................................. 3
2.0 Safety...........................................................................................................................................3
2.1 General instructions.......................................................................................................... 3
2.2 Warning............................................................................................................................... 3
2.3 Repair.................................................................................................................................. 4
2.4 Safety instructions............................................................................................................. 4
Please use it normally.........................................................................................................4
3.0 Packing and transportation...................................................................................................... 5
3.1 Packing................................................................................................................................5
3.2 Transportation................................................................................................................. 5
3.3 Storage................................................................................................................................ 5
3.4 Supply list............................................................................................................................5
3.5 Ambient temperature......................................................................................................6
3.6 Air humidity......................................................................................................................... 6
3.7 Base frame installation (fig3.7.1~3.7.4)...................................................................... 6
3.8 Installation main body （Fig 3.8.1~3.8.4）................................................................ 7
3.9 Power connection （fig 3.9）....................................................................................... 9
4.0 Technical specifications............................................................................................................ 9
4.1 Introduction of function characters................................................................................. 9
4.2 Electrical parameters...................................................................................................... 12
4.3 Feed size.......................................................................................................................... 12
4.4 Collecting bucket............................................................................................................. 13
4.5 Instrument size.................................................................................................................13
4.6 Weight............................................................................................................................... 13
4.7Floor space........................................................................................................................ 13
5.0 Installation.................................................................................................................................13
5.1 Instrument units（fig 5.1.1~fig 5.1.5）........................................................................ 13
5.2 Spare parts function list..................................................................................................15
5.3 Open/close grinding room door （fig 5.3.1~5.3.2）.................................................17
5.4 Install/replace the cutting type accessories（fig 5.4.1~5.4.4）.............................. 18
5.5 Install/replace the cross beater type accessories......................................................19
5.6 Install/replace the rotor beater type accessories....................................................... 21
5.7 Collecting bucket installation （fig 5.7）.................................................................... 23
5.8 Control panel（fig 5.8）...........................................................................................23
5.9 Control panel function list...............................................................................................23
5.10 Feed sample materials.................................................................................................24
5.11 Preparation before grinding......................................................................................... 24
5.12 Universal hopper （fig 5.12）..................................................................................25
5.13 Standard hopper （Fig 5.13）................................................................................... 25
5.14 Start instrument............................................................................................................. 26
5.15 Stop the instrument.......................................................................................................26
5.16 Using the cyclone..........................................................................................................26
Beijing Grinder Instrument Co., Ltd. Tel：010-82363430 Fax：010-82363435 www.grindertech.cn
2
5.17 Install the cyclone..........................................................................................................26
6.0 Routine................................................................................................................................... 28
6.1 Clean................................................................................................................................. 28
6.2 Maintenance.....................................................................................................................29
6.3 Functional inspections.................................................................................................... 29
6.4 Copyright...........................................................................................................................29
6.5 Modification...................................................................................................................... 29
Beijing Grinder Instrument Co., Ltd. Tel：010-82363430 Fax：010-82363435 www.grindertech.cn
3
1.0 Notes on the Manual
This manual covers all the contents of the CM100M directory,In order to operate safely,
please read the relevant parts of the manual.
This manual does not include repair information. If you need to repair, please contact
the supplier or GRINDER directly.
2.0 Safety
Multi-functional CM 100M, which is a unique and advanced product from Grinder,a
multi-functional mill combines three types:cutting type,cross beater type and rotor beater
type to one machine.
cutting type, which handles soft ,medium-hard ,tough, flexible and fibrous materials.
cross beater type, which can deal with the hard, brittle materials .
rotor beater type, which can handle soft, tough materials
By replacing different type of grinding accessories can achieve three different grinding
functions to expand application scope greatly.The three kinds of grinding accessories are
modular design, which can replace each of them easily with short time.CM100M with
1500W three-phase frequency control motor and work in with transformer to make the
speed can be adjusted continuously from 500~4000rpm, so as to meet different grinding
requirements for different properties samples.
2.1 General instructions
As a user,be sure that you are authorized to use CM100M.Fully understand technical
documents before using.
Before operation new user must be trained by the skilled personnel or operate strictly
according to this instruction.
Read and fully understand the safety instructions before using.
Improper handling may cause personal injury and damage to the instrument. Please
pay attention to your personal safety.
Please ensure that unqualified personnel do not operate the equipment.
2.2 Warning
Beijing Grinder Instrument Co., Ltd. Tel：010-82363430 Fax：010-82363435 www.grindertech.cn
4
Please pay your attention to the content of ‘Note’ in this manual to ensure your personal
safety and avoid damaging to equipment.
2.3 Repair
This manual does not include any repair information. For your safety, please contact
GRINDER company’s authorized agents or GRINDER technical service center for repair.
2.4 Safety instructions
Please use it normally
GRINDER shall not be liable for any personal injury or damage to the equipment due to
failure to comply with the safety instructions.
No changes can be made to the instrument, and use the accessories and accessories
approved by the GRINDER. Otherwise, any of our warranty commitments will no longer be
valid.
Packaging
Please keep the packing materials during the warranty period. Otherwise, we shall not be
able to guarantee your rights in case of packing complaint.
Transport
The machine may not be knocked, shaken or thrown during transport. So as not to
damage the electronic and mechanical parts of the instrument.
Temperature change
If CM100M is subjected to large temperature changes(such as in air transport), the
formation of condensate should be prevented to avoid damage to electronic and
mechanical components.
Packing list
Upon receipt of the goods, if you find any shortage or damage to the equipment, please
inform the transport company or contact the GRINDER (within 24 hours). Delayed
complaints may not be accepted.
Installation requirements
If the environment temperature is too high, too low or high humidity, it will be possible to
cause damage to the electronic parts or mechanical parts of the instrument, and the
performance will be unknown.
Power connection
Beijing Grinder Instrument Co., Ltd. Tel：010-82363430 Fax：010-82363435 www.grindertech.cn
5
Before connecting the power supply, please pay attention to the value of the nameplate on
the instrument so as not to damage the electronic parts or mechanical parts of the
instrument.
3.0 Packing and transportation
3.1 Packing
The packing should be suitable for transportation and meet the CM100M packing
requirements.
Note：
Please retain the original packing during the warranty period so that when the equipment
is defective, and you need to have it shipped back intact to avoid any damage during
transit.
3.2 Transportation
During transportation, please do not throw, knock or oscillate, so as not to damage the
electronic and mechanical parts of the instrument.
Note：
If the temperature changes greatly (e.g., air transport), condensation water should be
prevented to avoid damaging the electronic components.
3.3 Storage
Please ensure that the CM100M is kept dry during storage.
3.4 Supply list
CM100M main machine：1set
Base frame：1 set
Collecting bucket：1 pc
Manual：1 book
Power code：1pc（10A/250V）
Fuse：2个(10A/250V)
Beijing Grinder Instrument Co., Ltd. Tel：010-82363430 Fax：010-82363435 www.grindertech.cn
6
Please check whether the supply is complete after receiving goods, including
individual additional orders.
Notice：
Please inform GRINDER company within 24 hours if the shipment is not complete or
damaged. Delayed complaints may not be accepted.
3.5 Ambient temperature
From 5℃to 40℃
Note：
When the ambient temperature exceeds or falls below that specified, the electronic and
mechanical components may be damaged, And performance data changed to an
unknown extent.
3.6 Air humidity
At a higher air humidity, the electronic and mechanical components may be damaged, and
performance data changed to an unknown extent.
3.7 Base frame installation (fig3.7.1~3.7.4)
The base frame is included in CM100M main machine( fig 3.7.1),which is also a optional
part and can be order separately,the base frame is consist with three installed spare
parts:
BS：base
LR：Left roller rail
RR：Right roller rail
Fig 3.7.1
Beijing Grinder Instrument Co., Ltd. Tel：010-82363430 Fax：010-82363435 www.grindertech.cn
7
BSS
Installation step：
Fasten the base BS with left roller rail LR and right roller rail RR with the supplied
screws and tools.(fig 4.5-2~4.5-3)
Fig 3.7.2 fig 3.7.3
Screws：M8×16 hexagon socket head screws* 4pcs
Tool：5mm hexagon socket wrench *1pc
The final installed base frame BBS (Fig 3.7.4)
Fig 3.7.4
3.8 Installation main body （Fig 3.8.1~3.8.4）
If the instrument is transported in separate packing, the base frame and main body
should be installed on site. The installation steps as following:
Beijing Grinder Instrument Co., Ltd. Tel：010-82363430 Fax：010-82363435 www.grindertech.cn
8
BSS
SC
Please loosen and remove 4 pcs of transporting fixed screws SC and 2 pcs of
fixing parts TA with supplied screws and tool.(Fig 3.8.1)
（fig 3.8.1）
Tool：13mm open spanner 1pc
Screws（SC）：M8×25 hexagon socket head screws 4pcs
Installation step（fig 3.8.2~3.8.3）
Please place the main body on the base frame BSS and fixed them with 4 pcs of
screws SC.
（fig 3.8.2)
SC
TA
Beijing Grinder Instrument Co., Ltd. Tel：010-82363430 Fax：010-82363435 www.grindertech.cn
9
Fig 3.9
Tool：13mm open spanner 1pc
Screw（SC）：M8×25 hexagon socket head screws *4pcs
Note：
The main body’s gross weight is approx 85 kgs,
Need to 2 persons to move it！
（fig 3.8.3） （fig 3.8.4）
3.9 Power connection （fig 3.9）
The voltage and frequency of the power supply have
been marked on the nameplate.
Ensure that the voltage is in line with the actual
conditions.
please use the supplied CM100M power cord.
Fuse specification:10A/250VAC
4.0 Technical specifications
4.1 Introduction of function characters
Function：
CM1OOM can handle batch quantity samples,please open the grinding chamber door and
remove the rotor and grinding accessories after sample grinding,which is easy to clean.
Table of contents
Popular Kitchen Appliance manuals by other brands
Tayama
Tayama TYG-35AF instruction manual
AEG
AEG 43172V-MN user manual
REBER
REBER Professional 40 Use and maintenance
North American
North American BB12482G / TR-F-04-B-NCT-1 Assembly and operating instructions
Presto
Presto fountain popper instruction manual
Westmark
Westmark 1035 2260 operating instructions
