Extech Instruments DO210 User manual

UserGuide



DissolvedOxygenMeter

ModelDO210



www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

DO210-en-GB_v1.2 11/14

Introduction

ThankyouforchoosingtheExtechDissolvedOxygen/TemperatureMeterwhichsimultaneously

displaysDissolvedOxygenandTemperatureorOxygeninairandTemperature.Unitsofmeasure

aremg/lforDissolvedOxygen,%forOxygeninair,andoC/oFfortemperature.Oxygenis

measuredwitharemotesensorthatalsocontainsathermistorformeasuringairtemperature.

Advancedfeaturesincludealtitudeand%saltcompensation,datahold,autoshutoff,and

Min/Maxrecording.



MeterDescription



1. Maindisplaydigitsformeasurementsandprogrammingvalues

2. Temperaturereading

3. Power/Escapebutton

4. Function/Hold/Uparrowbutton

5. Record/Enterbutton

6. Setting/Downarrowbutton

7. BatteryCompartment(onback)

8. Probeconnectingcable

9. Probe



www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

DO210-en-GB_v1.2 11/14

GettingStarted

Note:Thedissolvedoxygenprobeassemblymaybeshippedfromthefactorydry.Ifthe

probedoesnotcontainelectrolytesolution,refertotheElectrolyteReplacementsection

belowforinformationonaddingtheelectrolytesolutionpriortoinitialuse.

FillingtheElectrolyteContainerPriortoInitialUse

1. Unscrewandremovetheelectrolytecontainerfromthetipof

theprobe.

2. Filltheelectrolytecontainerwithnewelectrolyte.

3. Screwtheelectrolytecontainerbackontotheelectrodeholder

andprobehandle.ExcessElectrolytemaybeforcedout

throughthethreads.Wipeclean.

4. Lightlytaptheprobetoremoveairbubbles.



Calibration

Forfirsttimeuseorafterlongperiodsofnon‐use,calibratetheinstrumentusingtheprocedure

below.Theprocedureshouldbeperformedinanopen,well‐ventilatedarea.

1. Connecttheoxygenprobeplugtotheprobeinputsocket.

2. SwitchONthemeterbypressingthePower/ESCbutton.

3. Thelowerdisplayshouldindicatethe%O2unitsymbolandatemperaturevalue.

4. Theupperdisplaywillbeginfluctuating.Waitapproximately3minutesfortheupper

displaytostabilize.

5. PresstheHOLDbuttonandthedisplaywillshowtheHOLDicon.

6. PresstheRECbutton.Thedisplaywillshow"CAL"flashingandthemeterdisplaywill

begincountingdownfrom30tozero;themeterwillthendisplaytheENDicon.

7. Theupperdisplaywillshowavalueapproximately20.9or20.8(typicalconcentrationof

oxygeninair).

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

DO210-en-GB_v1.2 11/14

DissolvedOxygen(DO)Measurements

MeasurementPreparation

Beforetakingmeasurements,performthecalibrationdescribedaboveifnecessary.

TakingMeasurements

1. PressandholdtheFunctionbuttonforatleast2secondstochangefrom%O2tomg/Lor

frommg/Lto%O2.ForDOmeasurementsselectmg/L(milligramsperliter).

2. Immersetheprobeinthesolutionundertest.Foroptimumautomatictemperature

compensation,immersetheprobetoadepthofatleast4"(10cm).

3. Waituntilthedisplaystabilizes.

4. Thevelocityoftheliquidcomingintocontactwiththeprobemustbeatleast0.6to1

ft/min(0.2to0.3m/s).Ifthesolutionisstanding,stirthesolutionwiththeprobeoruse

anagitator.

5. Rinsetheprobewithcleanwateraftereachuseandcovertheprobeheadwiththe

probeheadprotectivecover.

OxygeninAir(%O2)Measurements

MeasurementPreparation

Beforetakingmeasurements,performthecalibrationdescribedearlierifnecessary.

TakingMeasurements

1. PressandholdtheFunctionbuttonforatleast2secondstochangefrommg/Lto%O2if

necessary.Foroxygeninairmeasurementsbesuretoselect%O2.

2. Holdtheprobeintheareaundertestandwaituntilthedisplaystabilizes.

TemperatureMeasurements

Thelowerdisplaywillindicatethetemperatureofameasuredsolutionorthetemperatureof

theair(dependingonwhattypeofmeasurementtheuserisperforming).Tochangethe

temperatureunitofmeasureoC/oFfollowtheprocedurebeloworrefertotheSettingsmode

section:

PressandholdtheSettingbuttonfor5seconds(untilabeepisheard)toaccessthe

Settingmode

PresstheSettingbuttonmomentarilytwomoretimes

UsetheUParrowbuttontoselectoCoroFtemperatureunits

PressENTERtosavethesettingandpressESCtoreturntothenormalmodeofoperation



DataHold

PresstheHoldkeytofreezethedisplayedvalue.TheLCDwilldisplayHOLDalongwiththeheld

reading.PresstheHoldkeyagaintoreleasethedataholdfunction.



www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

DO210-en-GB_v1.2 11/14

MIN/MAXDataRecording

Whenselected,theDataRecordingfunctionrecordstheMin/Maxreadings.Tostartadata

recordingsession:

1. PresstheRECbuttononce.TheRECindicatorwillappearonthedisplay.PresstheREC

buttonagainandRECMAXwilldisplayonthescreenalongwiththemaximumvalue.

2. PresstheRECbuttonagainandthedisplaywillshowRECMINandtheminimumvaluewill

bedisplayed.

3. ToreleasetheheldMAXorMINreading,presstheHOLDbuttonwhileeithertheRECMAX

orRECMINiconsarevisible;nowonlytheRECiconwillbevisible.Themeterisnow

continuingtomonitorthehighest(MAX)andlowest(MIN)readingsbutisdisplayingreal

timemeasurements.ToviewtheMAXandMINvaluesagainusetheRECbuttonas

describedearlier.

4. ToexittheRecordmode,pressandholdtheRECbuttonforatleast2seconds.Thedisplay

willreturntothenormaloperatingmode.



SettingsMode

BeforeaccessingtheSettingsmodeensurethatthemeterisnotintheHOLDorMIN/MAX

Recordingmodes.TousetheSettingsmode:

1. PressandholdtheSETTINGbuttonforatleast5seconds(untilabeepisheard)

2. UsetheSETTINGbuttontoscrollthroughtheSettingsoptionsTheoptionsare:

HIGH Altitudecompensationadjustment

SALt  %Saltadjustment

°C/°F Temperatureunitselection

OFF  Autopoweroffmanagement

3. RefertothefollowingsectionsfordetailedinstructionsonprogrammingtheSetting

modeparameters

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

DO210-en-GB_v1.2 11/14

AltitudeCompensationAdjustment(HIGH)

Ifthemeasurementenvironmentisnotatsealevelthealtitude(HIGH)valuemustbe

adjustedasdescribedbelow:

1. PressandholdtheSettingsbuttonfor5seconds(untilabeepisheard);themeter

willthendisplaythewordHIGHonthelowerleftandthealtitudecompensation

valueintheupperLCDareainlargerdigits

2. PressENTERandtheHIGHsymbolwillflash

3. Usethe▲and▼buttonstosetthedesiredaltitudecompensationinmeters

4. AfterselectingthedesiredvaluepressENTERtosaveandtosteptotheSalt

compensationparameter(orpressESCtoreturntothenormaloperatingmode)

5. Notethatthealtitudecompensationcanbeadjustedfrom0to3900meters;when

themeterispoweredOFFthevaluewillrevertto0meters(sealevel)

%SaltAdjustment

1. ContinuingfromtheprevioussectionintheSettingsmode:WhentheLCDshowsSALt

atthelowerleft,presstheENTERbutton

2. TheSALtsymbolwillflashandthedisplaywillshowthesaltcompensationvalueon

theupper,largeLCDdigits

3. Usethe▲

and▼

buttonstoadjustthedisplaytothedesired%SALtvalue

4. PressENTERtosavethedataandtosteptothenextparameter(orpressESCto

returntothenormalmodeofoperation)

5. The%saltvaluecanbeadjustedfrom0to39%salt(%weight).Whenthemeteris

poweredOFFthesaltvaluewillrevertto0%salt.

TemperatureUnitsSelection

ContinuingfromtheprevioussectionintheSettingsmode:

WhenoCoroFisdisplayed,pressthe▲buttontoselectthedesiredunits.PressENTERto

savetheselectionandtosteptothenextparameter(orpressESCtoreturntothenormal

modeofoperation).

AutoPowerOFFEnable/Disable

ContinuingfromtheprevioussectionintheSettingsmode:

WhenOFFYESorOFFNOisdisplayed,usethe▲buttontoselectYESorNO.

YES:AutopowerOFFenabled(meterwillautomaticallyswitchoffafter10minutesof

inactivity;NO:AutopowerOFFdisabled.

PressENTERtosavetheselectionandtoreturntothenormaloperatingmode.



www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

DO210-en-GB_v1.2 11/14

BatteryReplacement

The9Vbatterythatpowerstheinstrumentrequiresreplacingwhenthebatteryiconflasheson

thedisplay.Toreplacethebatteryfollowthestepsbelow:

1. Disconnecttheprobefromtheinstrument.

2. OpentherearbatterycompartmentusingascrewdrivertoremovethetwoPhillipshead

screwsthatsecurethecompartment.

3. Carefullyremovetheoldbatteryfromthecompartmentlidchamberandgentlyunsnap

thebattery’sterminalsfromthewired(red/black)connectors.

4. Installanew9Vbatterybysnappingthebatteryterminalsontothewiredconnectors

(observingcorrectpolarity)andinsertingthebatteryintothecompartmentlidchamber.

5. Installthecompartmentlidchamberintothemeterhousingandsecurewiththetwo

screws.



Neverdisposeofusedbatteriesorrechargeablebatteriesinhouseholdwaste.

Asconsumers,usersarelegallyrequiredtotakeusedbatteriestoappropriate

collectionsites,theretailstorewherethebatterieswerepurchased,orwherever

batteriesaresold.

Disposal:Donotdisposeofthisinstrumentinhouseholdwaste.Theuserisobligatedtotake

end‐of‐lifedevicestoadesignatedcollectionpointforthedisposalofelectricalandelectronic

equipment.



www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

DO210-en-GB_v1.2 11/14

ProbeHeadReplacement

Theprobehead(onthetipoftheprobe)holdsathinTeflon®membraneandanelectrolyte

container.Calibrationerrorsorreadingerrorscouldindicatelossofelectrolyteora

dirty/damagedmembrane.Themembraneisverydelicateandcaneasilybedamagedifit

comesincontactwithsolidobjects.ReplacementprobeheadsareavailablefromanExtech

distributor.

Replacementprocedure

1. Unscrewtheprobeheadandemptytheoldelectrolytefromthecontainer.

2. Fillthenewprobehead/electrolytecontainerwithelectrolyte.

3. Screwtheprobeheadontotheprobehandle.Excesselectrolytemaybeforcedoutthrough

thethreads.Wipeclean.

4. Lightlytaptheprobetoremoveanyairbubbles.

1. Probehandle

2. Temperaturesensor

3. ProbeHead



www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

DO210-en-GB_v1.2 11/14

Specifications

GeneralSpecifications

CircuitCustomone‐chipLSImicroprocessorcircuit

DisplayDualfunctionLCD

MeasurementsDissolvedOxygen%O2ormg/l(milligramsperliter);Oxygen

inair:%;Temperature:°C/°F

DataholdDataholdkeyfreezesdisplayedreading

SensorStructureRemotePolarographicDissolvedOxygenSensor

Temperaturesensor:Precisionthermistor

DatarecordingMin/Maxmemoryandrecall

AutopoweroffMeterturnsoffafter10minutes(canbedisabled)

Samplerate1.0Second(approx.)

OperatingconditionsTemperature:0to50°C(32to122°F);Humidity:<80%RH

Batterypower9Valkalinebattery

PowerConsumptionApprox.6.2mADC

Weight446g(0.98lbs.)includingbatteries&probe

DimensionsMaininstrument:135x60x33mm(5.3x2.4x1.3")

Probe:190x28mm(7.5"x1.1")length/diameter



ElectricalSpecifications

MeasurementRangeResolutionAccuracy

DissolvedOxygen0.0‐20.0mg/L0.1mg/L+0.4mg/L

Oxygeninair0‐100%O20.1%O2+0.7%O2

Temperature

(probeonly)

32to122oF

0to50oC

0.1oF/C±1.5oF

+0.8oC

Compensation

adjustments

Temperature(automatic)0to50oC(32to122oF)

Salt0to39%

Altitude0to3900meters



Allrightsreservedincludingtherightofreproductioninwholeorinpartinanyform

www.extech.com





www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Table of contents

Other Extech Instruments Measuring Instrument manuals

Extech Instruments

Extech Instruments SL250W User manual

Extech Instruments

Extech Instruments MO230 User manual

Extech Instruments

Extech Instruments SDL400 User manual

Extech Instruments

Extech Instruments SP505 User manual

Extech Instruments

Extech Instruments MA410T User manual

Extech Instruments

Extech Instruments ExStik II EC400 User manual

Extech Instruments

Extech Instruments TH10 User manual

Extech Instruments

Extech Instruments GRT350 User manual

Extech Instruments

Extech Instruments AN100-NIST User manual

Extech Instruments

Extech Instruments PQ3450-2-NIST User manual

Extech Instruments

Extech Instruments ExStik RE300 User manual

Extech Instruments

Extech Instruments HT30 User manual

Extech Instruments

Extech Instruments RH350 User manual

Extech Instruments

Extech Instruments 480836 User manual

Extech Instruments

Extech Instruments 407910 User manual

Extech Instruments

Extech Instruments LT10 User manual

Extech Instruments

Extech Instruments PQ3450-30 User manual

Extech Instruments

Extech Instruments 382095 User manual

Extech Instruments

Extech Instruments LT505 User manual

Extech Instruments

Extech Instruments RT32 User manual

Extech Instruments

Extech Instruments 445580 User manual

Extech Instruments

Extech Instruments UV510 User manual

Extech Instruments

Extech Instruments SDL400-NIST User manual

Extech Instruments

Extech Instruments CO250 User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual