Elcometer 319 S User manual
User Guide
Elcometer 319 Model S & T
Dewpoint Meter
www.elcometer.com
R
1
Gauge Overview
2
Box Contents
3
Using the Gauge
4
Getting Started
5
The Sensors
6
Setting Limits
7
Taking a Reading
8
Using External Temperature Probes
9
Statistics
10
Batching - Model T
11
Reviewing Batch Data - Model T
12
Menu Structure - Model S
13
Menu Structure - Model T
14
Downloading Data - Model T
15
Spares & Accessories
16
Warranty Statement
17
Technical Specification
18
Legal Notices & Regulatory Information
www.elcometer.com
For the avoidance of doubt, please refer to the original English language version.
Gauge Dimensions: 174 x 75 x 35mm (6.85 x 2.95 x 1.38")
Gauge Weight: 300g (10.5oz) - including batteries
© Elcometer Limited 2015 - 2016. All rights reserved. No part of this document may be reproduced, transmitted,
transcribed, stored (in a retrieval system or otherwise) or translated into any language, in any form or by any
means (electronic, mechanical, magnetic, optical, manual or otherwise) without the prior written permission of
Elcometer Limited.
Hg
CONTENTS
Pb
R
en-1
1 GAUGE OVERVIEW
1 Surface Temperature Probe
2 Air Temperature & Humidity Probe
3 LED Indicators - Red (left), Green (right)
4 LCD Display
5 Softkeys
6 On/Off Key
7 Wrist Strap Connection
8 USB Data Output Socket (below cover)
9 Battery Compartment
10 Integrated Magnets
11 K-Type Probe Connector (below cover)
www.elcometer.com en-2
2 BOX CONTENTS
Elcometer 319 Dewpoint Meter
Protective Pouch with Belt Clip
2 x AA Batteries
Wrist Harness
®
ElcoMaster Software & USB Cable (Model T only)
Calibration Certificate
User Guide
R
3
1
2
4
5
6
87
9
11
10
3 USING THE GAUGE
www.elcometer.com
en-3
a
R
e
g
f
h
h
i
d
b
c
j
k
l
m
n
o
p
q
r
a
Measurement Units -°C, g/kg,°F, gr/lb
b
Power: USB
c
Bluetooth On
d
Menu Softkey
e
Stats Softkey
f
Batch Softkey (Model T)
g
Hold Current Reading; Start / Stop Logging (Model T)
h
Trend Indicators - Value increasing or decreasing
i
Climatic Parameters - Maximum of 5
j
Power: Batteries - including battery life indicator
k
Manual Logging
l
Batch Softkey - when in batching (Model T)
m
Batch Number / Batch Reading Number (Model T)
n
Alarm - reading outside set and enabled limits
o
Softkeys Locked (Model T)
p
Interval Logging - when in batching (Model T)
q
Thermometer Mode On
r
External Probe Temperature
4.1 FITTING THE BATTERIES
Each gauge is supplied with 2 x AA alkaline
batteries.
To insert or replace the batteries:
1 Remove the battery cover by rotating the
retaining screw anti-clockwise.
2 Insert 2 batteries taking care to ensure
correct polarity.
3 Refit the cover and rotate the retaining screw clockwise to
secure.
The battery condition is indicated by a symbol in the top right of the
displa e more segments displayed, the better the y ( ). Th
condition of the batteries.
When no segments are displayed, it is not advisable to use the
gauge for interval logging over long periods of time (Model T only;
see Section 4.6 - ‘Setting Manual or Interval Logging’ on page en-7).
If the batteries are replaced during interval logging, the gauge may
show ‘Please Wait’ whilst it re-calculates the batch statistics.
When the batteries are nearly depleted, the battery power supply
symbol will start flashing and the gauge emits short beeps every 10
seconds to indicate that the batteries should be changed.
The gauge can also be powered via USB using the USB cable
supplied (Model T) or available to purchase as an accessory
(Model S) - see Section 15 - ‘Spares & Accessories’ on page en-21.
Note: The USB cable can not be used to charge the batteries.
4.2 SELECTING YOUR LANGUAGE
1 Press and hold the ON/OFF button until the Elcometer logo is
displayed.
2 Press Menu/Setup/Languages and select your language using
the softkeys.
3 Follow the on screen menus.
www.elcometer.com en-4
4 GETTING STARTED
R
+-
-+
To access the language menu when in a foreign language:
1 Switch the gauge OFF.
2 Press and hold the left softkey and switch the gauge ON.
3 Select your language using the softkeys.
4.3 SCREEN SETTINGS
A number of screen settings can be defined by the user via
Menu/Setup/Setup Backlight including:
Backlight Brightness; This can be set to ‘Low’, ‘Medium’ or
‘High’.
Backlight Timeout; The display will dim if inactive for the
period defined by the user. To adjust the backlight timeout use
the softkeys to highlight ‘Backlight Timeout’ and press
‘Sel’. Use the softkeys to set the required value - between
0 (off) and 60 seconds - and press ‘Ok’ to set or ‘Esc’ to
cancel.
The gauge can also be set to switch off automatically after a user
defined period of inactivity - between 1 and 10 minutes - via
Menu/Setup/Auto Switch Off.
Note: ‘Auto Switch Off’ is disabled when the gauge is powered by the USB
connection.
4.4 SETTING UP THE READING DISPLAY
The user can select up to five climatic parameters to be displayed
on screen. Measurements are taken for all climatic parameters but
only those selected are displayed. Users can select from:
RH; % Relative Humidity
Ts; Surface Temperature
Ta; Air Temperature
Td; Dewpoint Temperature - calculated from Ta and RH
TΔ; Delta Temperature - the difference between surface
temperature and dewpoint
Tdb; Dry Bulb Temperature - equal to Ta
4 GETTING STARTED (continued)
www.elcometer.com
en-5
R
Twb; Wet Bulb Temperature - calculated from Ta and RH
SH; Specific Humidity - calculated from Ta and RH
Note: The formula used for calculation of Twb and SH uses a fixed value of air
pressure set at 1.0 atmosphere (1013mbar). The accuracy of Twb and
SH will vary at other values of atmospheric pressure. This variation may
be greater than ±1°C for Twb and ±1% / 10 mbar for SH.
To setup the display:
1 Press Menu/Setup/Display/Select
Readings.
2 Use the softkeys to highlight the
required option and press ‘Sel’.
Pressing ‘Sel’ again will de-select the
option.
The gauge will beep if the user attempts to
select a parameter when five are already
selected in which case, a parameter must
be de-selected before another is chosen.
3 To select which parameter is shown in
the largest digits at the bottom of the
display, press
Menu/Setup/Display/Main Reading.
4 Use the softkeys to highlight the
required option from the list displayed
and press ‘Sel’.
Only those climatic parameters selected via Step 2 above will be available
for selection in the ‘Main Reading’ list.
To increase the size of the main reading, reduce the number of
parameters displayed on the reading screen.
Note: If a reading exceeds any set limits during measurement, it will be shown
flashing on the display, even if it has not been selected for display via
Steps 1-2 above.
4.5 SELECTING THE MEASUREMENT UNITS
a
A choice of measurement units is available ; °C, °F, g/kg, gr/lb. To
select the measurement units, press Menu/Setup/Units.
www.elcometer.com en-6
4 GETTING STARTED (continued)
R
a g/kg and gr/lb relate to ‘Specific Humidity’ measurements only.
The sensors for (a) humidity (RH) and air
temperature (Ta); and (b) surface
temperature (Ts) are located at the top of
the gauge.
Note: The surface temperature sensor is serialised
for calibration traceability purposes.
FOR ACCURATE READINGS
Do not obstruct airflow through the holes in the casing around
the humidity and air temperature sensors.
Keep fingers away from the holes - body heat can affect
readings.
Allow the gauge some time, approximately 20 minutes, to
acclimatise once it is brought from a cold environment into a
warm place and vice versa.
www.elcometer.com
en-7
R
4.6 SETTING MANUAL OR INTERVAL LOGGING
Users can choose to manually log readings - ‘Manual Logging’
(Model S & T) or program the gauge to take readings at set time
intervals and save the readings into the batch memory automatically
- ‘Interval Logging’ (Model T only).
To select ‘Manual Logging’ in immediate mode (Model S & T):
1 Press Menu/Setup/Manual Logging.
2 To select immediate saving of a reading, use the softkeys
to highlight ‘Save only’ and press ‘Sel’.
3 To select holding of a reading followed by an option to save,
use the softkeys to highlight ‘Hold & Save’ and press ‘Sel’.
The default setting is ‘Hold & Save’.
‘Manual Logging’ is also available when in batching (Model T).
‘Interval Logging’ is only available when in batching (Model T).
For information on creating a new batch with ‘Manual Logging’ or
‘Interval Logging’, see Section 10.1 ‘Creating a New Batch’ on
page en-15.
4 GETTING STARTED (continued)
5 THE SENSORS
a
b
www.elcometer.com en-8
R
TO AVOID DAMAGE
Do not use excessive force when measuring surface
temperature. Light contact between the probe and the surface is
sufficient. Using force does not increase the measuring speed
or improve the accuracy of the measurement, but it does
increase wear and/or damage to the sensor tip.
Do not drag the surface temperature probe over the surface to
avoid excessive wear.
The humidity sensor is fragile and should never be touched. Do
not use compressed air to clean the sensors or the gauge.
If the surface of the humidity sensor becomes saturated with
moisture, allow the moisture to evaporate fully in a dry
environment before using the gauge to take measurements.
Protect the gauge from paint dust and dirt as much as possible
as these can affect the long term accuracy of the humidity
sensor. Always keep the gauge in its protective pouch when not
in use.
Do not wash the sensors in water or with solvents.
5 THE SENSORS (continued)
6 SETTING LIMITS
A lower and/or upper limit can be set by the user for any or all the
climatic parameters.
Limits can be set for individual readings (when not in Batching) or
limits can be set for each batch (when in Batching).
To set limits for individual readings (Model S & T):
1 Press Menu/Set Limits.
2 Use the softkeys to highlight the required parameter and
press ‘Sel’.
3 Use the softkeys to highlight ‘High Limit on’ and press ‘Sel’
to enable the limit.
4 Use the softkeys to highlight ‘High Limit’ and press ‘Sel’.
www.elcometer.com
en-9
R
5 Use the softkeys to set the required value and press ‘Ok’
to set or ‘Esc’ to cancel.
6 If required, repeat Steps 3-5 to set and enable a low limit value.
7 Repeat Steps 2-6 for each climatic parameter as required.
To set limits for a batch (Model T):
Limits can be set when a new batch is created. Once a reading is
saved into the batch, limits cannot be amended and limits cannot be
added.
1 Press Batch/New Batch/Limits.
2 Use the softkeys to highlight the required parameter and
press ‘Sel’.
3 Use the softkeys to highlight ‘High Limit on’ and press ‘Sel’
to enable the limit.
4 Use the softkeys to highlight ‘High Limit’ and press ‘Sel’.
5 Use the softkeys to set the required value and press ‘Ok’
to set or ‘Esc’ to cancel.
6 If required, repeat Steps 3-5 to set and enable a low limit value.
7 Repeat Steps 2-6 for each climatic parameter as required.
Batch limits can be viewed at any time via Batch/Review Batches.
When the value of a parameter falls outside set and enabled limits;
the appropriate parameter icon flashes;
If a reading exceeds any set limits during measurement, it will be shown
flashing on the display, even if it has not been selected for display via
Menu/Setup/Display/Select Readings.
the alarm symbol is displayed next to the parameter;
the red LED flashes; b
an audible alarm sounds ;
when in batching (Model T); a reading which exceeds a high
limit is marked and a reading which exceeds a low limit is
marked .
Note: When the value of the parameter returns within limits, the alarm status is
cleared automatically.
6 SETTING LIMITS (continued)
b The volume of the alarm is determined by the beep volume set via Menu/Setup/Beep Volume
This manual suits for next models
2
Table of contents
Languages:
Other Elcometer Measuring Instrument manuals
Elcometer
Elcometer 456 User manual
Elcometer
Elcometer 112 User manual
Elcometer
Elcometer 6700 User manual
Elcometer
Elcometer 138 User manual
Elcometer
Elcometer 456 Model E User manual
Elcometer
Elcometer 456 User manual
Elcometer
Elcometer 2350 User manual
Elcometer
Elcometer 456 Ultra User manual
Elcometer
Elcometer 456 User manual
Elcometer
Elcometer 2080 User manual
Elcometer
Elcometer Elcomotor 312 User manual
Elcometer
Elcometer 701 User manual
Elcometer
Elcometer 456 User manual
Elcometer
Elcometer E224C-BI User manual
Elcometer
Elcometer 456 User manual
Elcometer
Elcometer 148 User manual
Elcometer
Elcometer SG80BDL User manual
Elcometer
Elcometer CG60DL User manual
Elcometer
Elcometer 456 User manual
Elcometer
Elcometer SCM400 User manual
