Clarke CHT691 User manual

OPERATING INSTRUCTIONS

GC01/12

TYROLEAN APPLICATOR GUN

Model: CHT691

Part No: 1801691

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

INTRODUCTION

Thank you for purchasing this CLARKE applicator gun.

Before using the product, be sure to read these instructions thoroughly. In

doing so you will ensure the safety of yourself and of others around you, and

you can look forward to the product giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase. This guarantee is invalid if the product is found to have been

abused or tampered with in any way, or not used for its intended purpose.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

CONTENTS

1 x Applicator Gun Assembly c/w comb assembly & spindle

1 x Operating Handle

1 x Reducer Plate

ASSEMBLY

The applicator gun should be

delivered with the revolving comb

and spindle assembled within the

unit, and the handle supplied loose.

1. Screw the handle into the right

hand end of the comb assembly

through the hole in the casing as

shown in Fig 1.

Note: If the handle were assembled at the left side, the handle would

unscrew during operation, therefore, the applicator gun is for

right-handed operation only.

Handle

Comb Assembly

Fig 1

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

OPERATION

1. Set the rod as required, by

tightening the wing nuts at each

side, as shown in Fig 2, taking

care the rod is set level.

2. Fill the body of the unit half full of

wall coating material. Do not

overfill.

• Wall coating materials are heavy

and easier to handle in small

quantities.

3. Rotate the handle in a clockwise

direction to spray the wall

coating material.

4. If required, attach the reducer

plate to the front of the unit for

coating small areas and re-

touching work. Insert the plate,

first, into the top of the front

opening, before sliding the lower

edge down into position as

shown in Fig 3.

CLEANING

1. To keep your applicator gun

clean and ready for use, wash

out thoroughly as soon as you

stop work.

• Residual material lodged in the

comb will greatly reduce its

future performance.

2. Unscrew the handle from one

end of the comb and the spindle

from the other end, then lift the comb assembly out of the casing as

shown in Fig 4, in order to clean it thoroughly with water.

REPLACEMENT PARTS

Replacement comb assemblies are available from your Clarke dealer as part

number: HTCHT69101.

ENVIRONMENTAL PROTECTION

Do not dispose of this product or damaged components with general

household waste. All tools, accessories and packaging should be sorted,

taken to a recycling centre and disposed of appropriately.

Comb just

touches rod

Wingnut

High

Low

Fig 2

Reducer plate

Fig 3

Spindle

Handle

Comb Assembly

Fig 4

This manual suits for next models

Table of contents

Other Clarke Tools manuals

Clarke

Clarke Air CHR9P User manual

Clarke

Clarke CHT403 User manual

Clarke

Clarke CBS4 User manual

Clarke

Clarke CAT138 Installation and operation manual

Clarke

Clarke KIT700 Instruction Manual

Clarke

Clarke CDTJ12 Instruction Manual

Clarke

Clarke METALWORKER CTR1 Instruction Manual

Clarke

Clarke X-pro CAT164 Installation and operation manual

Clarke

Clarke CHT637 Installation and operation manual

Clarke

Clarke X-PRO CAT208 Installation and operation manual

Clarke

Clarke CRT 40 User manual

Clarke

Clarke CAT33B Installation and operation manual

Clarke

Clarke CONTRACTOR CHJ110 Instruction Manual

Clarke

Clarke CONTRACTOR CLJ120 Instruction Manual

Clarke

Clarke CAT125 Installation and operation manual

Clarke

Clarke CAT114 Instruction Manual

Clarke

Clarke CAT120 Instruction Manual

Clarke

Clarke Strong-Arm CLL500 Manual

Clarke

Clarke Strong-Arm CFB600 User manual

Clarke

Clarke CHT738 Instruction Manual

Clarke

Clarke CMFT250 Instruction Manual

Clarke

Clarke CONTRACTOR CSJ100 Instruction Manual

Clarke

Clarke CAT33B Installation and operation manual

Clarke

Clarke Metalworker CPTN1 Instruction Manual

Popular Tools manuals by other brands

Martor

Martor SECUNORM 175 quick start guide

ERKCO

ERKCO 1000 user manual

jbc

jbc N4473 instruction manual

FEINMETALL

FEINMETALL FZWZ-SET-001 quick start guide

Worx Professional

Worx Professional Sonicrafter WU676 Original instructions

Gage Bilt

Gage Bilt GB713SH Original instructions

Hilti

Hilti DX 9-ENP Original operating instructions

norbar

norbar NORTRONIC 34399 Operator's manual

BGS technic

BGS technic 8578 manual

Makita

Makita DHR241 instruction manual

Motor Guard

Motor Guard JMB-1250 instructions

Power Adhesives

Power Adhesives 805-12 operating instructions

Clemco

Clemco 24189 quick start guide

VVG

VVG VNG 903 Series instruction manual

Hilti

Hilti FX 3-A operating instructions

Grizzly

Grizzly H6472 Manual insert

axing

axing BWZ 5-02 Operation instructions

Dh-Robotics

Dh-Robotics RGI-100 Short manual