Clarke CHT718 User manual

USER INSTRUCTIONS

GC06/12

UNIVERSAL HUB/BEARING

PULLER

Model No: CHT718

Part No: 1801718

2

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

INTRODUCTION

Thank you for purchasing this CLARKE product. The kit may be used for

installing seals and bearings into the hubs of most vehicles. It may also be

used for pulling hubs where the wheel flange is drilled and tapped so that the

road wheel is secured with bolts.

Please read and follow the instructions carefully. In doing so you will ensure

the safety of yourself and others around you, and you can look forward to

the product giving you long & satisfactory service.

Please keep these instructions in a safe place for future reference

KIT CONTENTS

A Sleeve 76mm (3”) HTCHT71810

B1 Cup- 86mm (3-13/32”) HTCHT71811

B2 Cup- 91mm (3-19/32”) HTCHT71812

C1 Bolt M14 x 90 HTCHT71813

D Flat Washer HTCHT71814

E Sleeve 36mm (1-7/16”) HTCHT71815

F Centre Bolt HTCHT71816

G Thrust Washers HTCHT71817

H Long Nut HTCHT71818

C2 Bolt M12 x 90 HTCHT71819

1 Disc - 55.5mm (2-3/16”)HTCHT71801

2 Disc - 59mm (2-11/32”) HTCHT71802

3 Disc - 62mm (2-7/16”) HTCHT71803

4 Disc - 65mm (2-9/16”) HTCHT71804

5 Disc - 66mm (2-19/32”) HTCHT71805

6 Disc -71.5mm (2-13/16”)HTCHT71806

7 Disc - 73mm (2-7/8”) HTCHT71807

8 Disc - 78mm (3-3/32”) HTCHT71808

9 Disc - 84mm (3-5/16”) HTCHT71809

3

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

METHOD OF USE

WARNING: THE VEHICLE MUST BE PROPERLY PREPARED, AND

ADEQUATELY SUPPORTED ON AXLE STANDS, ON FIRM LEVEL GROUND,

BEFORE ANY OPERATION USING THIS TOOL IS PERFORMED.

INSTALLING SEALS & BEARINGS

Assemble the parts as shown in the example, selecting the components

which fit the job in hand. Ensure the large nut (H) is screwed fully on to the

bolt (F), and all components are entirely square before tightening.

HUB PULLING

It is possible to remove a hub from the swivel joint,

using the bolts (C) supplied.

The appropriate size bolts are screwed into the holes

in the wheel flange, so that they bear up against

the surface of the swivel joint.

Screw in the bolts progressively to pull off the hub.

For hubs where the wheel is mounted on studs, a

slide hammer type puller must be used.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for its intended purpose. Faulty goods

should be returned to their place of purchase. No product can be returned

to us without prior permission. This guarantee does not effect your statutory

rights.

This manual suits for next models

1

Other Clarke Tools manuals

Clarke

Clarke CAT66 User manual

Clarke

Clarke CMC36B User manual

Clarke

Clarke CAR15PC User manual

Clarke

Clarke CHT637 Installation and operation manual

Clarke

Clarke CAT216 Installation and operation manual

Clarke

Clarke CHT403 User manual

Clarke

Clarke TPG30P User manual

Clarke

Clarke Air CAT62 Installation and operation manual

Clarke

Clarke CDTJ12 Instruction Manual

Clarke

Clarke Strong-Arm CLL500 Manual

Clarke

Clarke CHT878 User manual

Clarke

Clarke CHT697 Installation guide

Clarke

Clarke CAT29B Installation and operation manual

Clarke

Clarke CHT738 Instruction Manual

Clarke

Clarke CMFT220 Instruction Manual

Clarke

Clarke SBR305 Instruction Manual

Clarke

Clarke X-PRO CAT170 Installation and operation manual

Clarke

Clarke Air CHR9P User manual

Clarke

Clarke KIT700 Instruction Manual

Clarke

Clarke Strong-Arm CFB600 User manual

Clarke

Clarke CAR8P User manual

Clarke

Clarke X-PRO CAT208 Installation and operation manual

Clarke

Clarke METALWORKER CTR1 Instruction Manual

Clarke

Clarke CHT204 User manual

Popular Tools manuals by other brands

Martor

Martor SECUNORM 175 quick start guide

ERKCO

ERKCO 1000 user manual

jbc

jbc N4473 instruction manual

FEINMETALL

FEINMETALL FZWZ-SET-001 quick start guide

Worx Professional

Worx Professional Sonicrafter WU676 Original instructions

Gage Bilt

Gage Bilt GB713SH Original instructions

Hilti

Hilti DX 9-ENP Original operating instructions

norbar

norbar NORTRONIC 34399 Operator's manual

BGS technic

BGS technic 8578 manual

Makita

Makita DHR241 instruction manual

Motor Guard

Motor Guard JMB-1250 instructions

Power Adhesives

Power Adhesives 805-12 operating instructions

Clemco

Clemco 24189 quick start guide

VVG

VVG VNG 903 Series instruction manual

Hilti

Hilti FX 3-A operating instructions

Grizzly

Grizzly H6472 Manual insert

axing

axing BWZ 5-02 Operation instructions

Dh-Robotics

Dh-Robotics RGI-100 Short manual