BLOTZ B28-ME-010 User manual

28mm Middle Eastern Building #10

B28-ME-010

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due care and

remember to cut away from yourself at all times.

During the construction of this model, you may find it convenient to use pegs / elastic bands to hold pieces in place while

you allow glue to dry.

Remove the four inner walls and base from the sprue.

Glue them together as shown to form an open-top

box.

At this point it is a good idea to glue a weight to the

inside of the box to help the minarets stability. We

have used a number of Uk 2p coins.

Glue the “lid” in place.

Glue to the doorway arch to the box, so that its right

hand side is flush with the edge and it sticks out by

about 2mm on the left hand side.

Move around the box, adding the other outer wall

pieces. Leave this sub-assembly to dry.

Take the sides of the tower, two supports and the

end caps from the sprue.

Glue the four walls with lugs on the ends to the

supports, ensuring that all have the long lug at the

same end..

Glue the end caps on –the cap with only 4 holes goes

at the end with the long lugs (which will protrude

through it)

The larger end cap goes at the other end.

Glue this assembly on top of the base as shown, using

the lugs to position it.

Attach the other wall sections - making sure all the

wall sections are the same way round.

Take the upper windows, a support and a cap from

the sprue.

Glue the four window pieces with lugs to the

support.

Attach the “cap”

Then glue the other window pieces into place.

Glue this sub-assembly into position.

Take the eight balustrade pieces…

..and glue them around the cap on the tower as

shown.

Take the roof and roof supports from the sprue.

Glue a support to the back of each roof piece.

Glue each roof support to the roof, making sure they

are straight.

When all are in position, you should have a small

hole at the top of the roof (see above).

Glue the finneal into place.

The finished Minaret.

10mm 3x2 Residential Foyer

B10-MW-100

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due

care and remember to cut away from yourself at all times.

During the construction of this model, you may find it convenient to use pegs / elastic bands to hold

pieces in place while you allow glue to dry.

Foyer (B10-MW-100)

Start by removing the sections shown above (left)

from the sprue. There are enough parts to create

both doorway sections.

Glue them together as shown in the image on the

right.

Glue each doorway to the back of the long sides, using

the lugs/holes provided.

At the same time, glue a triangular bracer to the

back of the long sides at each end. Leave these to

dry.

Glue the shorter end walls into place to give a hollow

rectangle. Once this is dry, glue the decorative

columns and balconies into position.

10mm 3x2 Residential Middle

B10-MW-150

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due

care and remember to cut away from yourself at all times.

During the construction of this model, you may find it convenient to use pegs / elastic bands to hold

pieces in place while you allow glue to dry.

Mid-Section (B10-MW-150)

Remove the four walls and four triangular corner

bracers from the sprue. Glue the triangles to

non-etched side of the two long walls as shown

in the example above. Leave to dry.

Once the bracers are dry, apply a little glue to the side

lugs and glue the shorter walls in place as shown

above. You should now have a hollow square

structure. Leave it to dry.

Now remove the four rectangles from the sprue.

Each of these has a line etched across it. Apply

glue to one side of the line only and attach it (as

shown) to the centre bottom edge of each wall.

Finally glue the balconies into position.

10mm 3x2 Residential Roof

B10-MW-200

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due

care and remember to cut away from yourself at all times.

During the construction of this model, you may find it convenient to use pegs / elastic bands to hold

pieces in place while you allow glue to dry.

Roof Section (B10-MW-200)

Remove the four walls and roof from the sprue.

Apply glue to the edges of the roof and attach

the walls to it using the lugs provided (etched

detail outwards).

Glue the balconies into position below the

windows.

Now remove the four rectangles from the sprue.

Each of these has a line etched across it. Apply glue to

one side of the line only and attach it (as shown in the

example above) to the centre bottom edge of each

wall.

This manual suits for next models

Other BLOTZ Toy manuals

Popular Toy manuals by other brands

marklin

marklin 37321 instruction manual

Canon

Canon PAPER CRAFT Assembly instructions

GREAT PLANES

GREAT PLANES Pitts M-12S instruction manual

NOCH

NOCH 14261 manual

Hausler

Hausler 450 SE V2 quick start

Dynaflite

Dynaflite Daydream instruction manual

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Build instructions

Kenner

Kenner Batman 63651 instructions

LEGO

LEGO 8527 instructions

iKarus

iKarus ECO 8 Assembly instruction

Multiplex

Multiplex EasyStar II Building instructions

Walkera

Walkera 38 User handbook

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE manual

MD MXION SWD user manual

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway instructions

marklin

marklin 39671 user manual

Meccano

Meccano 15103 instructions

LEGO

LEGO TECHNIC 8735 instructions