BLOTZ B10-CS-209 User manual

10mm 3x3 Tower Block Foyer

B10-CS-209

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due

care and remember to cut away from yourself at all times.

During the construction of this model you may find it convenient to use pegs / elastic bands to hold

pieces in place while you allow glue to dry.

Foyer

Remove the inner front wall its “roof” and two

door frames from the sprue.

Attach the wall to the “roof” then glue the door

frames in position as shown.

Now remove the two side walls from the sprue.

Glue the side walls to the inner front wall assembly

aligning it using the holes/lugs provided.

Glue the outer front wall into place.

Then attach the back wall.

Glue the whole model to the base. Note there is

a “B” etched into the base which should be at the

back of the building.

Glue the door frames around the side doors and on

the back of the building.

Finally glue the sun-screens into place (etched

detail upwards).

10mm 3x3 Tower Block Middle

B10-CS-262

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due

care and remember to cut away from yourself at all times.

During the construction of this model you may find it convenient to use pegs / elastic bands to hold

pieces in place while you allow glue to dry.

Middle Section

Take the four walls and base from the sprue.

Glue the walls to the base as shown aligning them

using the holes / lugs provided.

Flip the whole thing upside down and glue the

support lugs into place.

Take the twelve sun-screen strips from the sprue and

attach three to each side of the building as shown

above.

10mm 3x3 Tower Block Roof

B10-CS-310

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due

care and remember to cut away from yourself at all times.

During the construction of this model you may find it convenient to use pegs / elastic bands to hold

pieces in place while you allow glue to dry.

Roof Section

Remove the base and four walls from the sprue.

Glue the walls to the base aligning them using the

holes / lugs provided.

Flip the roof assembly over and glue the four

support pieces into place as shown.

Put it back the right way up and attach the four sun-

shade pieces.

Other BLOTZ Toy manuals

Popular Toy manuals by other brands

marklin

marklin 37321 instruction manual

Canon

Canon PAPER CRAFT Assembly instructions

GREAT PLANES

GREAT PLANES Pitts M-12S instruction manual

NOCH

NOCH 14261 manual

Hausler

Hausler 450 SE V2 quick start

Dynaflite

Dynaflite Daydream instruction manual

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Build instructions

Kenner

Kenner Batman 63651 instructions

LEGO

LEGO 8527 instructions

iKarus

iKarus ECO 8 Assembly instruction

Multiplex

Multiplex EasyStar II Building instructions

Walkera

Walkera 38 User handbook

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE manual

MD MXION SWD user manual

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway instructions

marklin

marklin 39671 user manual

Meccano

Meccano 15103 instructions

LEGO

LEGO TECHNIC 8735 instructions