BLOTZ B10-CS-202 User manual
10mm 3x2 Industrial Foyer
B10-CS-202
Please read these instructions fully before starting construction.
PVA or equivalent glue will be required to stick sections together.
Sand paper can be used to gently clean any joints.
A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due
care and remember to cut away from yourself at all times.
During the construction of this model you may find it convenient to use pegs / elastic bands to hold
pieces in place while you allow glue to dry.
Foyer (B10-CS-202)
Remove the four wall sections and corner bracers
from the sprue as shown above.
Glue two corner bracers to the back of the two short
wall sections. Allow glue to dry.
Glue the two side walls to the end walls as shown
above.
Now remove the four decorative sections from the
sprue.
Glue these into position on the main walls using
the lines scored on the walls as a guide.
10mm 3x2 Industrial Middle
B10-CS-253
Please read these instructions fully before starting construction.
PVA or equivalent glue will be required to stick sections together.
Sand paper can be used to gently clean any joints.
A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due
care and remember to cut away from yourself at all times.
During the construction of this model you may find it convenient to use pegs / elastic bands to hold
pieces in place while you allow glue to dry.
Mid-Section (B10-CS-253)
Remove the four wall sections and corner bracers
from the sprue as shown above.
Glue two corner bracers to the back of the two short
wall sections. Allow glue to dry.
Glue the two side walls to the end walls as shown
above.
Now remove the four decorative sections from the
sprue.
Glue these into position on the main walls using
the lines scored on the walls as a guide.
Glue the four supports in place – the two longer ones
on the end walls and the short ones in the centre of
the long walls.
10mm 3x2 Industrial Roo
B10-CS-303
Please read these instructions fully before starting construction.
PVA or equivalent glue will be required to stick sections together.
Sand paper can be used to gently clean any joints.
A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due
care and remember to cut away from yourself at all times.
During the construction of this model you may find it convenient to use pegs / elastic bands to hold
pieces in place while you allow glue to dry.
Roo Section (B10-CS-301)
Remove the roof and four wall sections from the
sprue.
Glue them into position as shown above.
The Air-con unit is made from the four pieces as
shown.
Glue these together as shown above.
The glue the finished unit to the roof.
Finally add the decorative strips and supports.
Other BLOTZ Toy manuals
BLOTZ
BLOTZ B15-MW-007 User manual
BLOTZ
BLOTZ B20-DA-004 User manual
BLOTZ
BLOTZ B15-WW2-100 User manual
BLOTZ
BLOTZ B28-VSF-013 User manual
BLOTZ
BLOTZ B20-MD-019 User manual
BLOTZ
BLOTZ B10-MW-113 User manual
BLOTZ
BLOTZ 10mm Skyscraper Dice Tower User manual
BLOTZ
BLOTZ B15-CS-251 User manual
BLOTZ
BLOTZ Shako Rocket Tosen User manual
BLOTZ
BLOTZ B10-CS-209 User manual
BLOTZ
BLOTZ B10-MW-114 User manual
BLOTZ
BLOTZ 28mm Old West Store 2 B28-OW-109 User manual
BLOTZ
BLOTZ B28-ST-127 User manual
BLOTZ
BLOTZ B10-MW-112 User manual
BLOTZ
BLOTZ Old West Store 3 User manual
BLOTZ
BLOTZ B00-ACC-400 User manual
BLOTZ
BLOTZ Old West Store 8 User manual
BLOTZ
BLOTZ B28-OW-108 User manual
BLOTZ
BLOTZ B10-PS-004 User manual
BLOTZ
BLOTZ B28-WW2-301 User manual
