Zennio Tecla 55 X Sign User manual

Tecla 55 X Sign

PC-ABS Capacitive DND/MUR Buttons 55x55

ZVIT55X2

USER MANUAL

Application Programme Version: [1.0]

User Manual Version: [1.0]_a

www.zennio.com

 Tecla 55 X2 Sign 
https://www.zennio.com Technical Support: https://support.zennio.com 
 

CONTENTS 
Contents........................................................................................................................................ 2 
Introduction........................................................................................................................... 3 
1 Tecla 55 X2 Sign ............................................................................................................. 3 
2 Installation ..................................................................................................................... 4 
Configuration......................................................................................................................... 5 
1 General .......................................................................................................................... 5 
1.1 Configuration ............................................................................................................. 5 
1.2 Backlight..................................................................................................................... 7 
1.3 Sounds........................................................................................................................ 8 
1.4 Ambient Luminosity Sensor....................................................................................... 9 
1.5 Touch Locking ............................................................................................................ 9 
2 Indicators ..................................................................................................................... 11 
3 Buttons......................................................................................................................... 12 
3.1 Configuration ........................................................................................................... 12 
3.2 Disabled.................................................................................................................... 13 
3.3 Check Occupancy ..................................................................................................... 14 
3.4 Make-Up In Progress................................................................................................ 15 
4 Inputs........................................................................................................................... 18 
4.1 Temperature Probe.................................................................................................. 18 
ANNEX I. Communication Objects............................................................................................... 19 

Tecla 55 X2 Sign

https://www.zennio.com Technical Support: https://support.zennio.com

1INTRODUCTION

1.1 TECLA 55 X2 SIGN

Tecla 55 X2 Sign is a polycarbonate capacitive switch with backlit icons, in color, for the

selection and notification of room states. In this respect, its main functions are:

Notification of room state: Make-Up Room, Do Not Disturb and Make-Up in

Progress.

Checking occupancy status: Occupied or Not Occupied.

This application program has the following features:

2 buttons which can only be configured individually.

Horizontally or vertically-oriented configuration.

Light indicators (LEDs) which, in addition, could be associated with the

functionality of the buttons.

Buzzer for an audible acknowledgement of user actions (with the possibility of

disabling it either by parameter or by object).

Possibility of locking / unlocking the touch through binary orders or scenes.

Possibility of setting a press detection delay.

Ambient luminosity sensor for brightness automatic adjustment.

Proximity sensor for quick start.

One analogue/digital input for temperature probe.

Heartbeat or periodical “still-alive” notification.

Note: Tecla 55 X2 Sign application program can be downloaded to Tecla 55 X2 and vice

versa.

Tecla 55 X2 Sign

https://www.zennio.com Technical Support: https://support.zennio.com

1.2 INSTALLATION

Figure 1 shows the connection outline of Tecla 55 X2 Sign:

Figure 1. Schematic diagram Tecla 55 X2 Sign.

Tecla 55 X2 Sign is connected to the KNX bus through the built-in terminal (3). An external

DC power supply is not needed.

A short press on the programming button (5) will make the device enter the programming

mode. The programming LED (4) will then light in red. On the contrary, if this button is held

while the device gets connected to the bus, the device will enter the safe mode. In such

case, the programming LED will blink in red colour.

For detailed information about the technical features of Tecla 55 X2 Sign, as well as on

security and installation procedures, pleasereferto thedevice Datasheet, bundled within the

device packaging and also available at www.zennio.com.

1. Frame (sold separately).

2. Metallic levelling plate.

3. KNX Connector.

4. Programming LED.

5. Programming Button.

6. Fixing clips.

7. Temperature Probe Connector.

8. Touch Buttons.

9. Proximity and Luminosity Sensor.

10. Temperature Probe (included).

Tecla 55 X2 Sign

https://www.zennio.com Technical Support: https://support.zennio.com

2CONFIGURATION

After importing the corresponding database in ETS and adding the device into the topology

of the project, the configuration process begins by entering the Parameters tab of the device.

2.1 GENERAL

In order to allow the device to perform the desired functions, a number of options related to

its general behaviour must be parameterized.

2.1.1 CONFIGURATION

In the "Configuration" tab, the general settings are displayed. Most are checkboxes that

enable/disable other functionalities

ETS PARAMETERISATION

Figure 2. General

Tecla 55 X2 Sign

https://www.zennio.com Technical Support: https://support.zennio.com

The following parameters are shown:

Device Orientation [Horizontal (Rotated) / Vertical (Normal)]

: enables to assign a

horizontal or vertical orientation to the device, making it easier to identify the push-

buttons during the configuration process (ETS will show a figure with the final

distribution of the push-buttons).

Indicators [enabled]: read-only parameter to make it evident that the “Indicators”

tab is always enabled in the tab tree on the left. See section 2.2 for details.

Buttons [enabled/disabled]: enables or disables the “Buttons” tab in the tree on the

left. See section 0 for details.

Inputs [disabled/enabled]: enables or disables the “Inputs” tab in the tree on the

left, depending on whether the device will or will not be connected any external

temperature probe. See section 2.4 for details.

Heartbeat (Periodic Alive Notification) [disabled/enabled]: incorporates a one-bit

object to the project (“[Heartbeat] Object to Send ‘1’”) that will be sent periodically

with value “1” to notify that the device is still working (still alive).

Figure 3. Heartbeat.

Note: the first sending after download or bus failure takes place with a delay of up

to 255 seconds, to prevent bus overload. The following sendings march the period

set.

Sounds [Default/ Custom]: sets whether the soundfunctions (button beeps) should

work according to the pre-defined configuration or to a user-defined configuration.

See section 2.1.3 for details.

The default values of each parameter will be highlighted in blue in this document, as follows:

[default/rest of options].

Tecla 55 X2 Sign

https://www.zennio.com Technical Support: https://support.zennio.com

Ambient luminosity sensor [disabled/enabled]: enables setting the ambient

luminosity sensor. When the sensor is enabled, a new tab for its configuration is

shown. See section 2.1.4 for details.

Proximity Sensor [disabled/enabled]: enables the proximity sensor. This

functionality permits “waking up” the device when detecting presence.

Please refer to the specific manual “Proximity and Luminosity Sensor” (available

in Tecla 55 X2 Sign product section at the Zennio homepage, www.zennio.com) for

detailed information about the functionality and the configuration of the related

parameters.

Touch locking [disabled/enabled]: enables or disables the “Touch locking” tab in

the tree on the left. See section 2.1.5 for details.

Update Objects [Disabled / After Programming / After Reset / After Programming

and Reset]: enables the sending of read requests to update the objects “[General]

Room State” and “[General] Presence: Occupancy State”. There are four options

available:

➢[Disabled]: no read request, therefore objects are not updated.

➢[After Programming]: read requests are sent after a complete or partial

download, after the parameterised delay ([0…10…255] [s/min/h]).

➢[After Reset]: read request are sent whenareset occurs(bus failure or theReset

Device ETS option), after the parameterised delay ([0…10…255] [s/min/h]).

➢[After Programming and Reset]: combination of the two above options.

Time to Consider Inactivity [1…30…255][s/min/h]: allows setting a time after

which, if no pulsation or proximity detection has occurred, the indicators turn off (or

acquire the brightness level configured, see section 2.1.2).

2.1.2 BACKLIGHT

Tecla 55 X2 Sign enables management the indicators brightness according to two operating

modes: normal mode and night mode.

Please refer to the specific manual “Brightness” (available in the Tecla 55 X2 Sign product

section at the Zennio website, www.zennio.com) for detailed information about the

functionality and the configuration of the related parameters.

Tecla 55 X2 Sign

https://www.zennio.com Technical Support: https://support.zennio.com

2.1.3 SOUNDS

Tecla 55 X2 Sign is capable of emitting a brief beep as an acoustic feedback when a button

is pressed.

Enabling the button sounds can be done either by parameters or through an object, being

also possible to define in parameters if the button sounds should be initially enabled or not.

The range of sounds emitted will be different depending on the sound type selected.

ETS PARAMETERISATION

In case the default button beep sound matches the requirements of the installation and the

doorbell and alarm functions are not necessary, the Sounds parameter in the general

“Configuration” tab (see section 2.1.1) can be set to “Default”. This will also imply that the

button beeps will be unconditional, as it will not be possible to disable this function through

an object.

On the other hand, if set to “Custom”, a specific tab named “Sounds” will show up in the tab

tree on the left. The initial configuration of this screen is equivalent to the aforementioned

default option.

Figure 4. Sounds

The default configuration of this tab is equivalent to the one mentioned above. However, the

following parameters can be customized:

Sound Type [Sound 1 / Sound 2]: sets which sounds range incorporates the

device.

Disable button sound [disabled/enabled]: enables the buttons beeping. If enabled,

the following parameters will also be available:

Tecla 55 X2 Sign

https://www.zennio.com Technical Support: https://support.zennio.com

➢Enable / Disable button sounds through a 1-bit object [disabled/enabled]:

makes it possible to disable / resume the button beeping function in runtime by

writing to a specific object (“[General] Sounds –Disabling Button Sound”). If

enabled, it will be shown:

•Value [0 = Disable; 1 = Enable / 1 = Disable; 0 = Enable]: Configures the

values that will disable/enable the acoustic signals after pressing.

➢Status After ETS Download [Enabled / Disabled]: sets whether the button

beeping function should start up enabled or disabled after an ETS download.

The project topology shows the following objects by default:

“[General] Scene: Receive”and “[General] Scene: Send”: objectsfor respectively

receiving and sending scene values from/to the KNX bus whenever it is necessary.

“[General] Room State”: enables to set and know the room status. The values

available are: 0 = Normal, 1 = Make-Up Room, 2 = Do Not Disturb, 3 = Make-Up in

Progress.

“[General] Proximity Sensor”, “[General] External Proximity Detection”and

“[General] Proximity Detection”: 1-bit object whose functionality is tied to the

proximity sensor. For further information, please refer to the user manual

“Proximity and Luminosity Sensor” (available in the Tecla 55 X2 Sign product

section at the Zennio homepage, www.zennio.com).

2.1.4 AMBIENT LUMINOSITY SENSOR

Tecla 55 X2 Sign incorporates a luminosity sensor to receive and monitor ambient

brightness measurement.

Please refer to the specific manual “Luminosity and Proximity Sensor” (available in the

Tecla 55 X2 Sign product section at the Zennio homepage, www.zennio.com) for detailed

information about the functionality and the configuration of the related parameters.

2.1.5 TOUCH LOCKING

The touch panel of Tecla55 X2 Sign canbe optionally locked and unlockedanytime by writing

a configurable one-bit value to a specific object provided for this purpose. It can also be done

through scene values.

Tecla 55 X2 Sign

https://www.zennio.com Technical Support: https://support.zennio.com

While locked, pressing on the buttons will be ignored: no actions will be performed (and no

indicators will change their states) when the user touches on any of the controls.

ETS PARAMETERISATION

After enabling Touch Locking in “Configuration” tab, a new tab will be incorporated into the

tree on the left.

Figure 5. Touch Locking

1-Bit Object [disabled/enabled]: when marked, a specific drop-down list will show

up to select which value should trigger which action.

➢Value [0 = Unlock; 1 = Lock / 0 = Lock; 1 = Unlock]: these values are received

through the object “[General] Touch Locking”.

Scene Object [disabled/enabled]: when marked, two specific textboxes will show

up to enter the scene numbers [1…64] that should trigger each action. These

values are to be received through the general “[General] Scene: Receive” object.

This manual suits for next models

Table of contents

Other Zennio Controllers manuals

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual