Zennio MAXinBOX 16 Guide

MAXinBOX 16 Plus

Multi-Function Actuator 16 outputs 16A

ZIO-MB16P TECHNICAL DOCUMENTATION

FEATURES

•4 different configurable blocks: shutter channels (up to 8), individual

outputs (up to 16) and 2-pipe fan coil control (up to 4)

•Outputs suitable for capacitive loads, maximum 140 µF

•Manual output operation with push button and LED status indicator

•20 logic functions

•Output timing

•Total data saving on KNX bus failure

•Integrated KNX BCU

•Dimensions 67 x 90 x 140 mm (8 DIN units)

•DIN rail mounting according to IEC 60715 TH35, with fixing clamp

•Possibility of connecting different phases in adjacent outputs

•Conformity with the CE directives (CE-mark on the right side)

1. Upper outputs

2. Lower outputs

3. Programming/test LED

4. KNX Connector

5. Fixing clamp

6. Programming/test button

7. Output status LED indicator

8. Output control button

A1 A2

B1 B2 A1 A2

LM M

B1 B2

A1 A2

B1 B2

B1A1 B2A2

A1 A2

B1 B2

B1 B2B1 B2

A1 A2

B1 B2

L1 L2 L1 L2

L1 L2 L3 L4

A1 A2 B1 B2 C1 C2 D1 D2

E1 E2 F1 F2 G1 G2 H1 H2

L1 L2

L3 L1

F1 F2 F3 V1

Figure 1: MAXinBOX 16 Plus

Programming/Test button: short press to set programming mode. If this button is held while plugging the device into the KNX bus, it enters the safe

mode. If this button is held for more than 3 seconds, the device enters the test mode.

Programming/Test LED: programming mode indicator (red). When the device enters the safe mode, it blinks (red) every half second. The manual mode

is indicated by the green color. During the start-up (reset or after KNXbus failure) and ifthe device is not in safemode, it startsa blue blinking sequence.

GENERAL SPECIFICATIONS

CONCEPT

DESCRIPTION

Type of device

Electric operation control device

KNX supply

Voltage (typical)

29 VDC SELV

Voltage range

21..31 VDC

Maximum

consumption

Voltage

29 VDC (typical)

6.5

188.5

24 VDC¹

240

Connection type

Typical TP1 bus connector for 0.80 mm Ø rigid cable

External power supply

Not required

Operation temperature

0 °C .. +55 °C

Storage temperature

-20 °C .. +55 °C

Operation humidity

5 .. 95%

Storage humidity

5 .. 95%

Complementary characteristics

Class B

Protection class / Overvoltage category

II / III (4000 V)

Operation type

Continuous operation

Device action type

Type 1

Electrical stress period

Long

Degree of protection / Pollution degree

IP20 / 2 (clean environment)

Installation

Independent device to be mounted inside electrical panels with DIN rail (IEC

60715)

Minimum clearances

Not required

Response on KNX bus failure

Data saving according to parameterization

Response on KNX bus restart

Data recovery according to parameterization

Operation indicator

The programming LED indicates programming mode (red) and test mode

(green). Each output LED indicates its status

Weight

525 g

PCB CTI index

175 V

Housing material / Ball pressure test temperature

PC FR V0 halogen free / 75 °C (housing) - 125 °C (connectors)

¹ Maximum consumption in the worst-case scenario (KNX Fan-In model).

SAFETY INSTRUCTIONS ANDADDITIONAL NOTES

•Installation should only be performed by qualified professionals according to the laws and regulations applicable in each country.

•Do not connect the mains voltage nor any other external voltage to any point of the KNX bus; it would represent a risk for the entire

KNX system. The facility must have enough insulation between the mains (or auxiliary) voltage and the KNX bus or the wires of other

accessories, in case of being installed.

•Once the device is installed (in the panel or box), it must not be accessible from outside.

•Keep the device away from water (condensation over the device included) and do not cover it with clothes, paper or any other material

while in use.

•The WEEE logo means that this device contains electronic parts and it must be properly disposed of by following the instructions at

https://www.zennio.com/en/legal/weee-regulation.

OUTPUTS SPECIFICATIONS AND CONNECTIONS

CONCEPT

DESCRIPTION

Number of outputs

Output type / Disconnection type

Potential-free outputs through bistable relays with tungsten pre-contact /

Micro-disconnection

Rated current per output

AC 16(6) A @ 250 VAC (4000 VA)

DC 7 A @ 30 VDC (210 W)

Maximum load per output

Resistive

4000 W

Inductive

1500 VA

Maximum inrush current

800 A/200 μs

165 A/20 ms

Connections in adjacent outputs

Possibility of connecting different phases. It is not allowed to connect power

supplies of different order, SELV with NO SELV, in the same block

Maximum current per block

40 A

Short-circuit protection

Overload protection

Connection method

Screw terminal block (0.5 Nm max.)

Cable cross-section

1.5-4 mm² (IEC) / 26-10 AWG (UL)

Outputs per common

Maximum response time

10 ms

Mechanical lifetime (min. cycles)

3 000 000

Electrical lifetime (min. cycles)1

100000 @ 8 A / 25000 @ 16 A (VAC)

¹ Lifetime values could change depending on the load type.

⚠In order to ensure the expected status

of the relays, please check that the

device is connected to the KNX bus

before energizing the power circuit.

WIRINGDIAGRAMS

Figure 2: Wiring example (from left to right): 2 loads, 2 loads

connected to different phases, shutter and fan coil

A1 A2

B1 B2 A1 A2

LM M

B1 B2

A1 A2

B1 B2

B1A1 B2A2

A1 A2

B1 B2

B1 B2B1 B2

A1 A2

B1 B2

L1 L2 L1 L2

L1 L2 L3 L4

A1 A2 B1 B2 C1 C2 D1 D2

E1 E2 F1 F2 G1 G2 H1 H2

L1 L2

L3 L1

F1 F2 F3 V1

Figure 3: Mounting MAXinBOX 16 Plus on DIN rail

Removing MAXinBOX 16 Plus from DIN rail:

Attaching MAXinBOX 16 Plus to DIN rail:

This manual suits for next models

Other Zennio Controllers manuals

Zennio

Zennio Roll-ZAS User manual

Zennio

Zennio MINiBOX 0-10V X3 User manual

Zennio

Zennio MAXinBOX 66 User manual

Zennio

Zennio MAXinBOX 24 v2 Guide

Zennio

Zennio MAXinBOX FC 0-10V FAN Guide

Zennio

Zennio AudioInRoom User manual

Zennio

Zennio MINiBOX 0-10V X3 User manual

Zennio

Zennio MINiBOX 40 v3 User manual

Zennio

Zennio IDAC User manual

Zennio

Zennio MINiBOX 25 v3 Guide

Zennio

Zennio ACTinBOX MAX6 User manual

Zennio

Zennio ZoningBOX 6 Guide

Zennio

Zennio MAXinBOX 8 v3 Guide

Zennio

Zennio MAXinBOX 8 Plus Guide

Zennio

Zennio AudioInRoom ZMU-AUIR User manual

Zennio

Zennio IRSC Plus User manual

Zennio

Zennio MAXinBOX 8 v3 Guide

Zennio

Zennio FANinBOX 230V 1CH Guide

Zennio

Zennio MAXinBOX 16 Plus Guide

Zennio

Zennio FANinBOX 110V 1CH Guide

Zennio

Zennio ZCL-MCC User manual

Zennio

Zennio MAXinBOX FC 0-10V VALVE User manual

Zennio

Zennio MAXinBOX FANCOIL 2CH2P User manual

Zennio

Zennio MINiBOX 25 Guide

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual