Zennio LUMENTO X3 Guide



LUMENTOX3

LEDDIMMING

RGBCONTROLLER

ZN1DI‐RGBX3        

TechnicalDocumentation



Page 1/ 2

MAIN FEATURES

Control of RGB LEDs or 3 independent channels.

External power supply required (12-24 VDC).

LEDs test function

KNX BCU integrated

KNX and CE mark

SIZE AND DESCRIPTION

N Element

1 KNX Connector

2 KNX Programming button

3 KNX Programming and internal test LED

4 Test button

5 Test LED and Reversed polarity indicator

6 External power supply terminal block

7 LEDs control terminal block

GENERAL SYSTEM SPECIFICATIONS

Type of device Electric Operation Control Device

KNX Supply

Voltage 29V DC SELV

Voltage range 20…31V DC

Power consumption 145 mW

Bus connection Typical BUS connector TP1, 0.50mm2 section

External Power Supply 12 – 24V DC

Power Supply cable section 1.5 mm² to 2.5 mm²

Type of control PWM (150, 300, 488 ó 600 Hz)

Ambient Temperature 0ºC to +45ºC

Storage Temperature -5ºC a +50ºC

Ambient Humidity 30 to 85% RH (no condensation)

Storage Humidity (relative) 30 to 85% RH (no condensation)

Complementary Characteristics Class B

Safety Class II

Operation Type Continuous operation

Device Action Type Type 1

Electrical solicitations period Long

Type of Protection IP20

Assembly Independent control assembly device

Connect Lumento as near as possible to both, the LED to dimmer and the external power supply

Power Failure response (bus) Data saving

Response when restarting (bus) Data saving

KNX Programming button: a push button to set the programming mode. If this button is held while plugging the device into the

KNX bus, it goes into secure mode.

KNX Programming and internal test LED: the red LED indicates programming mode. When the device goes into secure mode, it

blinks red every 0.5 seconds. The blinking blue LED indicates internal test.

Test button: it tests the functioning of channels connected to the device. Push and hold for 3 seconds to get in/out of the testing

mode.

Test LED and polarity: tricolored LED that indicates which channel (red=channel 1/R, green=channel 2/G, blue=channel 3/B) is

being tested. White light indicates that the device is in test mode. Orange light indicates reverse polarity in external power supply.





LUMENTOX3

LEDDIMMING

RGBCONTROLLER

ZN1DI‐RGBX3        

TechnicalDocumentation



Page 2/ 2

WIRING AND ASSEMBLY DIAGRAMS

Recommended installation: NOT recommended:

Verticalposition.

If there is not any other

possibility, install

terminal block up

(see fig.)

SAFETY INSTRUCTIONS

Do not connect Mains Voltage (230 V) or any other external voltages to any point of the BUS. Connecting an external voltage

might put the entire KNX system at risk.

Make sure during the installation that there is always sufficient insulation between the mains voltage 230V and the bus or the

extension inputs.

When Overheating protection is active, the device will decrease the luminosity level and control frequency. Further information,

please read manual.

The voltage of the power supply connected to Lumento will never exceed the voltage required for the load, which is specified

by the manufacturer. Not following this recommendation would mean a risk for the installation.

Operation indication

Programming/internal test LED indicates: programming mode (red lighting), safe mode (red

blinking) and internal test (blue blinking). Test LED indicates: White, device in test mode; Red, test

channel 1 (R); Green, test channel 2 (G); Blue, test channel 3 (B). Reverse polarity of external

power supply is indicated by the Test LED with orange light.

PCB CTi index 175 V

Enclosure PC-ABS, flammability category Class D

Size Without terminal blocks: 144x44x22mm / With terminal blocks: 157x44x22mm

Weight 102 g.

OUTPUTS SPECIFICATIONS AND CONNECTIONS

Maximum current per channel 2.5A @ 25ºC ambient temperature

Number of channels 3

Total power connected 90W (12V DC) or 180W (24V DC)

Connection Type Terminal block (screw)

Cable Section 1.5 mm² to 2.5 mm²

Load type Common anode

Shortcut protection Yes

Overheating protection Yes

External power supply:

+ and - terminals of

external power supply 12-

24 VDC



LEDs

The LEDs load is connected to the terminal block, matching the anode or the anode

common terminal of the LED stripes with C (anode)

Correspondence

C: Anode 2: Green 1: Red 3: Blue 4: - s

are -

ssembly:

Screw mounting, 2 holes of 3.5 mm

diameter. Screws not included.

This manual suits for next models

Other Zennio Controllers manuals

Zennio

Zennio MINiBOX 20 User manual

Zennio

Zennio MAXinBOX 16 Guide

Zennio

Zennio ALLinBOX 1612 v2 User manual

Zennio

Zennio ZCL-MCC User manual

Zennio

Zennio HeatingBOX 230V 4X Guide

Zennio

Zennio MAXinBOX 16 Plus Guide

Zennio

Zennio MAXinBOX FANCOIL 4CH2P Guide

Zennio

Zennio MAXinBOX FC 0-10V VALVE User manual

Zennio

Zennio ZN1VI-TPZAS User manual

Zennio

Zennio HeatingBOX 230V 4X Guide

Zennio

Zennio FANinBOX 230V 1CH Guide

Zennio

Zennio MAXinBOX FC 0-10V FAN Guide

Zennio

Zennio Tecla 55 User manual

Zennio

Zennio ZCL-8HT230 User manual

Zennio

Zennio MAXinBOX FC 0-10V FAN User manual

Zennio

Zennio FANinBOX 110V 1CH Guide

Zennio

Zennio MAXinBOX SHUTTER 8CH v3 Guide

Zennio

Zennio MINiBOX 45v2 User manual

Zennio

Zennio MAXinBOX Hospitality ZCL-HP126 User manual

Zennio

Zennio MINiBOX 25 v3 Guide

Zennio

Zennio IRSC Zone User manual

Zennio

Zennio MAXinBOX FC 0-10V VALVE User manual

Zennio

Zennio MINiBOX 0-10V X3 User manual

Zennio

Zennio MINiBOX 40 v3 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual