Zennio HeatingBOX 230V 4X Guide

HeatingBOX 230V 4X

Heating actuator with 4 outputs 230VAC

ZCL-4HT230 Technical Documentation

FEATURES

4 configurable outputs for 230V valve control.

4 thermostats.

10 Logic functions.

Total data saving on power failure.

Manual control through buttons and status LED indicators.

Common 230V supply required for the 4 outputs.

KNX BCU integrated.

Size 67 x 90 x 35 mm (2 DIN units).

DIN rail unit assembly (EN 50022), with snap fit clamp.

CE directives compliant.

GENERAL SYSTEM SPECIFICATIONS

CONCEPT

DESCRIPTION

Type of device

Electric operation control device

KNX

supply

Voltage (typical)

29VDC SELV

Voltage range

21…31VDC

Maximum

consumption

Voltage

29VDC (typical)

7,5

217,5

24VDC(1)

240

Bus connection

Typical bus connector TP1, 0,80mm² section

External power supply

230V 50/60Hz (only phase, for valve supply)

Ambient temperature

from 0ºC to +55ºC

Storage temperature

from -20ºC to +55ºC

Ambient humidity

5 to 95% RH (no condensation)

Storage humidity (relative)

5 to 95% RH (no condensation)

Complementary characteristics

Class B

Safety class

Operation type

Continuous operation

Device action type

Type 1

Electrical solicitations period

Long

Type of protection

IP20, clean environment

Assembly

Independent control assembly device to be mounted inside of electrical panels with

DIN rail (EN 50022).

Minimal clearances

Not required

KNX bus failure response

Data saving according to parameterization.

Response when restarting KNX bus

Data recovering change according to parameterization.

Operation indication

Programming LED indicates programming mode (red) and test mode (green). Each

output LED indicates its status (fixed = active output; flashing = overload or short-

circuit error)

Weight

98g

PCB CTI index

175V

Enclosure

PC FR V0 halogen free

(1)

Maximum consumption in the worst case scenario (KNX Fan-In model)

Programming/test button: short button press to set programming mode. If this button is held while plugging the device into the KNX bus, it goes into

safe mode.

Programming/Test LED: programming mode indicator (red). When the device goes into safe mode, it blinks (red) every half second. The manual

mode is indicated by the green color. During start up (after reset or power failure) and if the device is not in safe mode, LEDs indicator blink red once.

1. 230V input (live phase) 2. Valve outputs 3. Output control button 4. Output status indicator LED

5. Programming/Test LED 6. Programming/Test button 7. KNX connector

Figure 1. HeatingBOX 230V 4X

SAFETY INSTRUCTIONS

Installation should only be performed by qualified electricians following applicable regulations on preventing accidents, as

required by law

Do not connect Main Voltage (230VAC) or any other external voltages to any point of the BUS.

Connecting an external voltage might put the entire KNX system at risk.

Make sure during the installation that there is always sufficient insulation between the mains voltage 230VAC and the bus or

the extension inputs.

Once the device is installed, it must not be accessible from the outside.

Keep away from water and do not cover the device with clothes, paper or any other material when in use.

The WEEE logo means that this device contains electronic parts and it must be discarded properly following the instructions

of http://zennio.com/weee-regulation.

Several valves per output

connection schematic

One valve per output

connection schematic

Removing HeatingBOX 230V 4X from DIN rail:

Attaching HeatingBOX 230V 4X to DIN rail:

Connecting more than one valve to each output is allowed as long as the maximum current per output is not exceeded:

OUTPUT SPECIFICATIONS AND CONNECTIONS

CONCEPT

DESCRIPTION

Number of outputs

Output type

Solid state switching device

Maximum values per

output

Quantity of valves(2) 5

Stationary current

200mA (considering an ambient temperature of 35ºC)

Inrush current

2,5A

Short-circuit protection

YES

Overload protection

YES

Connection method

Cable screw terminal

Cable cross-section

0,5 mm² to 2,5mm² (26-12 AWG)

(2) This value could be more restrictive depending on the valve stationary current and inrush current.

Figure 2. Mounting HeatingBOX 230V 4X

on a DIN rail

NOTE: Simultaneous connection of

one valve to several outputs is not

allowed.

Valve 1

Valve n

(n≤5)

Valve

230V~

50/60Hz

Other manuals for HeatingBOX 230V 4X

This manual suits for next models

Table of contents

Other Zennio Controllers manuals

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual