Zennio MAXinBOX 8 Plus Guide

MAXinBOX 8 Plus

Multi-function actuator with 8 outputs 16A

ZIO-MB8P Technical Documentation

FEATURES

2 different configurable blocks:

Shutter channels (up to 4).

Individual outputs (up to 8).

2-pipe fan coil control (up to 2 units).

Manual output operation with push button and LED

status indicator.

Suitable for capacitive loads, maximum 140 µF.

Logical functions included.

Output timing facilities.

Total data saving on power failure

Size 67 x 90 x 80 mm (4.5 DIN units).

DIN rail unit assembly (EN 50022), with snap fit clamp.

No external power supply required other than the bus.

KNX BCU integrated.

Possibility to connect different phases in adjoining

outputs.

CE directives compliant.

Programming/test button: short button press to set programming

mode. If this button is held while plugging the device into the KNX

bus, it goes into safe mode. If this button is held more than 3

seconds, the device goes into manual mode (test mode)

LED: programming mode indicator (red). When the device goes into

safe mode, it blinks (red) every half second. The manual mode is

indicated by the colour green. During start up (after reset or power

failure) and if the device is not in safe mode, LED blinks in blue for a

few seconds

Figure 1. MAXinBOX 8 Plus

GENERAL SYSTEM SPECIFICATIONS

CONCEPT

DESCRIPTION

Type of device

Electric operation control device

KNX supply

Voltage (typical)

29V DC SELV

Voltage range

21…31V DC

Maximum

consumption

Voltage

29VDC (typical)

5.8

168.2

24VDC(1)

240

Bus connection

Typical bus connector TP1, 0,50 mm² section

External power supply

Ambient temperature

from 0ºC to +55ºC

Storage temperature

from -20ºC to +70ºC

Ambient humidity

5 to 95% RH (no condensation)

Storage humidity (relative)

5 to 95% RH (no condensation)

Complementary characteristics

Class B

Safety class

Operation type

Continuous operation

Device action type

Type 1

Electrical solicitations period

Long

Type of protection

IP20, clean environment

Assembly

Independent control assembly device to be mounted inside of electrical panels

with DIN rail (EN 50022).

KNX bus failure response

Data saving and relays open if channel configured as shutter.

Response when restarting KNX bus

Data recovering and output status change according to programming when

recovering.

Operation indication

Programming LED indicates programming mode (red) and test mode (green).

Output status LED indicators reflect current output state.

Weight

290 g.

PCB CTI index

175 V

Enclosure

PC FR V0 halogen free

(1) Maximum consumption in the worst case scenario (KNX Fan-In model)

1. Upper

outputs

2. Lower output

screws

3.Programming/Test

LED

4.KNX

connector

5.Programming/Test

button

6.Output control

button

7.Output status LED

indicator

WIRING AND ASSEMBLY DIAGRAMS

SAFETY INSTRUCTIONS

Installation should only be performed by qualified electricians following applicable regulations on preventing accidents, as

required by law.

Do not connect Mains Voltage (230 V) or any other external voltages to any point of the bus.

Connecting an external voltage might put the entire KNX system at risk.

Make sure during the installation that there is always sufficient insulation between the mains voltage 230V and the bus or

the extension inputs.

Once the device is installed, the output terminal should not be accessible.

The WEEE logo means that this device contains electronic parts and it must be discarded properly following the

instructions of http://zennio.com/weee-regulation.

OUTPUTS SPECIFICATIONS AND CONNECTIONS

Contact type

Potential free outputs through bistable relays with tungsten pre-contact.

Disconnection type

Micro-disconnection

Rated current by output

16(6)A * 250V AC (4000 VA) 16(6)A * 30V DC (480W)

Maximum inrush current

800A/200μs (fluorescent lamps)

165A/20ms (resistive lamps)

Outputs per common

1 individual output

Different phases connection

Possibility to connect different phases in adjoining outputs

Maximum current

80A

Maximum power

Resistive load

4000W

Inductive load

1500W

Connection type

Terminal block (screw)

Recommended cable section

0,25 mm² to 4 mm² (26-10AWG)

Cable type

Stranded or solid wire.

Maximum response time

50 ms

Expected life

Mechanical (min)

3 million operations (60cpm)

Electrical (min.)

100.000 cycles at max. current (6cpm and resistive load)

Attaching MAXinBOX 8 Plus to DIN rail:

Removing MAXinBOX 8 Plus from DIN rail:

Figure 3. Installation of MAXinBOX 8 Plus on DIN rail

Figure 2. Wiring examples (from left to right): channel A as shutter channel, individual outputs in channel A with the same

and different phases and channel A and B as fan coil controller (2 pipe and three-speed fan).

This manual suits for next models

Table of contents

Other Zennio Controllers manuals

Zennio

Zennio MAXinBOX FANCOIL 4CH2P Guide

Zennio

Zennio MAXinBOX FC 0-10V FAN Guide

Zennio

Zennio MAXinBOX FC 0-10V VALVE User manual

Zennio

Zennio MAXinBOX 66 User manual

Zennio

Zennio ZIO-IB24 User manual

Zennio

Zennio ZN1CL-IRSC User manual

Zennio

Zennio MAXinBOX 16 Guide

Zennio

Zennio IRSC Plus User manual

Zennio

Zennio DIMinBOX 2CH ZDI-DB2C User manual

Zennio

Zennio MAXinBOX User manual

Zennio

Zennio ZoningBOX 6 Guide

Zennio

Zennio FANinBOX 110V 1CH Guide

Zennio

Zennio MAXinBOX 24 Guide

Zennio

Zennio ZCL-MCC User manual

Zennio

Zennio inBOX 24 vT User manual

Zennio

Zennio FANinBOX 230V 1CH Guide

Zennio

Zennio inBOX 24 v2 User manual

Zennio

Zennio Roll-ZAS User manual

Zennio

Zennio ACTinBOX MAX6 User manual

Zennio

Zennio Tecla 55 X Sign User manual

Zennio

Zennio MAXinBOX 8 Guide

Zennio

Zennio MINiBOX 45v2 User manual

Zennio

Zennio ALLinBOX 1612 Guide

Zennio

Zennio MINiBOX 0-10V X3 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual