YASKAWA MP2000iec Administrator guide

Page 1 of 21

Example Code Manual

Example Code Manual for Linear Flying Shear on MP2000iec

Sigma-5 demo using Camming

Applicable Product: MP2000iec, MotionWorks IEC

Yaskawa Electric America

2121 Norman Drive South

Waukegan, IL 60085

1-800-927-5292

Subject: Example Code Manual Product: MP2000iec Doc#: EM.MCD.09.095

Title: Example Code Manual for Linear Flying Shear on MP2300Siec Sigma-5 Demo using camming

July 13, 2009 Page 2 of 21

Application Overview

This document explains how to demonstrate the linear flying shear application with camming on the MP2000iec –

Sigma-5 demo box. The algorithm and core program elements are explained in detail.

Application Highlights:

Industry: Automation industry using electronic camming for registration based applications

Major Features: Electronic camming, cam shifts on the fly based on high speed registration

Products Used:

Component

Servopack

Motor

Controller

Software MotionWorks IEC, CamTool

Product and Model Number

Sigma-5 MECHATROLINK II Rotary type

SGMAV, SGMJV

MP2000iec

Subject: Example Code Manual Product: MP2000iec Doc#: EM.MCD.09.095

Title: Example Code Manual for Linear Flying Shear on MP2300Siec Sigma-5 Demo using camming

July 13, 2009 Page 3 of 21

Application Explanation

The sample code explained in this manual simulates the linear flying shear application as shown in Figure 1

below. The conveyor is the master. The ball screw unit is the slave that cams to the master axis based on a

registration mark. The cutting axis shown in the figure has not been incorporated into the sample code.

Figure 1: Linear Flying shear unit

The relation between the master and slave is given by the following profile (figure 2).

Figure 2: Stages of slave cam profile

Subject: Example Code Manual Product: MP2000iec Doc#: EM.MCD.09.095

Title: Example Code Manual for Linear Flying Shear on MP2300Siec Sigma-5 Demo using camming

July 13, 2009 Page 4 of 21

Figure 3: Critical positions on the cam master slave profile

Figure 3 details the critical points on the master and slave profiles. The algorithm followed to execute the linear

flying shear is shown in Figure 4. The algorithm starts with the shear axis (slave) at the home position and the

master axis running at a constant velocity. The slave axis waits for a registration mark from a part or on the

master axis. This triggers a shift in the master position such that the start of the cam cycle comes by when the

registration mark reaches the slave home position after covering the sensor to start distance (SSD). Once the

slave cams in and is synchronized, the window for capturing next registration latches opens up (when the slave

passes 30 mm of travel in the forward direction). If a registration is captured when the window for capture is

open, the position is stored and the calculation for phase and master distance is performed. The shift cannot

start immediately because when the shearing process is in progress, the slave and master need to be in tight

sync. Only after the shear is done, can the shift for the next part start. This is determined using a dead man area

on the slave’s position profile (user defined).

Subject: Example Code Manual Product: MP2000iec Doc#: EM.MCD.09.095

Title: Example Code Manual for Linear Flying Shear on MP2300Siec Sigma-5 Demo using camming

July 13, 2009 Page 5 of 21

Figure 4: Linear flying shear algorithm

Subject: Example Code Manual Product: MP2000iec Doc#: EM.MCD.09.095

Title: Example Code Manual for Linear Flying Shear on MP2300Siec Sigma-5 Demo using camming

July 13, 2009 Page 6 of 21

The phase is calculated by noting the difference in two consecutive latches on a 360 degree cycle. The master

distance is calculated as (SSD – (SSP – Master shifted position)) where SSD is distance the part has to travel to

get to the shear home position. SSP is the shift start position which is the position on the master from where the

shift can start. This is shown in Figure 5.

Figure 5: Implementation of cam shift

Figure 6 is an illustration of continuous part registration at unequal intervals. Shift one is executed for the first

latch (registration) seen in figure 6. Since the second registration was very early in a cycle, the shift to get the

slave back to home position is very large. This large shift over a small distance causes the slave to return back to

home in a very fast move on the return stroke as can be seen from shift 2. Since the third registration happens

almost at the end of the window, the phase shift is small and it has more distance over which to implement the

shift. It can be seen from Figure 6 that the third shift does not cause a major change in the cam profile.

Subject: Example Code Manual Product: MP2000iec Doc#: EM.MCD.09.095

Title: Example Code Manual for Linear Flying Shear on MP2300Siec Sigma-5 Demo using camming

July 13, 2009 Page 7 of 21

Figure 6: Multiple continuous registrations at unequal intervals

Figure 7 is an illustration of a first part detection or part detection after a cam out. It can be seen that at part

detection, the master position is 32 degrees. Sensor to home distance is 180 degrees. This means that the cam

cycle will have to start when the actual master position is 32 + 180 = 212 degrees. This first part shift can be

seen in Figure 7. If a part is not detected in the window area, a cam out is commanded and after the cam out is

done, a phase shift to negate all cumulative phase shifts is carried out so that the total shift becomes zero and

the master position and shifted master position match up as can be seen at the end of the profiles in figure 7.

Subject: Example Code Manual Product: MP2000iec Doc#: EM.MCD.09.095

Title: Example Code Manual for Linear Flying Shear on MP2300Siec Sigma-5 Demo using camming

July 13, 2009 Page 8 of 21

Figure 7: First part detection or part detection after a cam out

Demo Instructions:

The master axis (Left axis) is configured to be in rotary mode with a 360 degree cycle. (1 rev or motor = 360 user

units). The slave axis is configured as a linear axis with 1 rev of the motor = 100 mm of linear travel.

1) Make sure the servo axes on the demo case are tuned for improved performance

2) Manually orient the slave shear axis (right axis) such that the arrow points up. Flip SI5 switch on and off to set

that position as the home position for the slave axis. The position at which the master (left axis) is will be set as

its zero position too. The orientation of the master axis does not matter in this step.

Subject: Example Code Manual Product: MP2000iec Doc#: EM.MCD.09.095

Title: Example Code Manual for Linear Flying Shear on MP2300Siec Sigma-5 Demo using camming

July 13, 2009 Page 9 of 21

Figure 8: Demo case controls for sample program

3) Enable the servos using DI0. Leave DI0 on

Subject: Example Code Manual Product: MP2000iec Doc#: EM.MCD.09.095

Title: Example Code Manual for Linear Flying Shear on MP2300Siec Sigma-5 Demo using camming

July 13, 2009 Page 10 of 21

4) Flip DI1 on and off. This is to home the slave axis. On starting up, the slave axis is already in its home

position.

5) Turn on DI2. This will start the master axis jog. The master axis will jog at 90 degrees /second. To stop the

master jog, turn DI2 off.

6) When DO2 lights up, it is an indication that the controller program is ready for registration.

7) Flip SI4 on the first row on and off. This simulates a part or registration mark. DO2 will turn off. The slave axis

will wait for the master axis to turn 180 degrees (distance from sensor to shear’s home) from where the mark

was seen and then start the cam profile. The slave axis travel one way is 250 mm or 2.5 revs on the demo.

When the slave passes 30 mm travel, DO2 turns on and indicates that the system is ready for another mark.

DO2 will be on until the window is closed (240 mm on the slave). The slave’s shift in profile during the travel back

to home will depend on when the registration was seen in the cycle. If the part was detected early (closer to 30

mm), the move back on the slave will be rapid. If the part was detected later (closer to 240 mm), the move back

will be slow.

If a part is not detected while the slave is synchronized to the master and the window is over (DO2 turns off), the

slave cams out and stays at the home position until the next part comes along. The system will be ready for

registrations (DO2 on) as soon as the cam out is done.

This manual suits for next models

Table of contents

Other YASKAWA Controllers manuals

YASKAWA

YASKAWA SI-EM3 User manual

YASKAWA

YASKAWA MP23 Series User manual

YASKAWA

YASKAWA YRC1000micro User manual

YASKAWA

YASKAWA Z1000 CIMR-ZU*A Series User manual

YASKAWA

YASKAWA Sigma II Series User manual

YASKAWA

YASKAWA PROFINET V1000 User manual

YASKAWA

YASKAWA PROFINET V1000 User manual

YASKAWA

YASKAWA V1000 Series User manual

YASKAWA

YASKAWA Z1000U Series User manual

YASKAWA

YASKAWA SI-EL3 User manual

YASKAWA

YASKAWA motoman NX100 User manual

YASKAWA

YASKAWA motoman NX100 User manual

YASKAWA

YASKAWA PROFINET V1000 User manual

YASKAWA

YASKAWA PROFINET V1000 User manual

YASKAWA

YASKAWA JEPMC-PSA3012-E User manual

YASKAWA

YASKAWA JEPMC-BUB3005-E User manual

YASKAWA

YASKAWA MP2200 User manual

YASKAWA

YASKAWA SI-EM3 User manual

YASKAWA

YASKAWA YRC1000 User manual

YASKAWA

YASKAWA U1000 iQpump Drive User manual

YASKAWA

YASKAWA GA800 600 V Drive Instruction Manual

YASKAWA

YASKAWA Motoman DX200 User manual

YASKAWA

YASKAWA FSDrive-MV1000 Series User manual

YASKAWA

YASKAWA JOHB-GA50 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide