YASKAWA YRC1000micro User manual

MANUAL NO.

HW1484566

YRC1000micro OPTIONS

INSTRUCTIONS

FOR GROUP CHANGE FUNCTION

Upon receipt of the product and prior to initial operation, read these instructions thoroughly, and

retain for future reference.

MOTOMAN INSTRUCTIONS

MOTOMAN- INSTRUCTIONS

YRC1000micro INSTRUCTIONS

YRC1000micro OPERATOR’S MANUAL

YRC1000micro MAINTENANCE MANUAL

YRC1000micro ALARM CODES (MAJOR ALARMS) (MINOR ALARMS)

The YRC1000micro alarm codes above consists of “MAJOR ALARMS” and “MINOR ALARMS”.

1/18

181283-1CD

HW1484566

DANGER

• This manual explains the group change function of the

YRC1000micro system. Read this manual carefully and be sure to

understand its contents before handling the YRC1000micro. Any

matter not described in this manual must be regarded as

“prohibited” or “improper”.

• General information related to safety are described in “Chapter 1.

Safety” of the YRC1000micro INSTRUCTIONS. To ensure correct

and safe operation, carefully read “Chapter 1. Safety” of the

YRC1000micro INSTRUCTIONS.

CAUTION

• In some drawings in this manual, protective covers or shields are

removed to show details. Make sure that all the covers or shields

are installed in place before operating this product.

• YASKAWA is not responsible for incidents arising from unauthorized

modification of its products. Unauthorized modification voids the

product warranty.

NOTICE

• The drawings and photos in this manual are representative

examples and differences may exist between them and the

delivered product.

• YASKAWA may modify this model without notice when necessary

due to product improvements, modifications, or changes in

specifications. If such modification is made, the manual number will

also be revised.

• If your copy of the manual is damaged or lost, contact a YASKAWA

representative to order a new copy. The representatives are listed

on the back cover. Be sure to tell the representative the manual

number listed on the front cover.

2/18

iii

HW1484566

Notes for Safe Operation

Read this manual carefully before installation, operation, maintenance, or

inspection of the YRC1000micro.

In this manual, the Notes for Safe Operation are classified as “DANGER”,

“WARNING”, “CAUTION”, or “NOTICE”.

Even items described as “CAUTION” may result in a serious accident in

some situations.

At any rate, be sure to follow these important items.

DANGER

Indicates an imminently hazardous

situation which, if not avoided, will

result in death or serious injury.

Safety Signs identified by the signal

word DANGER should be used

sparingly and only for those

situations presenting the most

serious hazards.

WARNING

Indicates a potentially hazardous

situation which, if not avoided, will

result in death or serious injury.

Hazards identified by the signal

word WARNING present a lesser

degree of risk of injury or death than

those identified by the signal word

DANGER.

CAUTION

Indicates a hazardous situation,

which if not avoided, could result in

minor or moderate injury. It may

also be used without the safety alert

symbol as an alternative to

“NOTICE”.

NOTICE

NOTICE is the preferred signal word

to address practices not related to

personal injury. The safety alert

symbol should not be used with this

signal word. As an alternative to

“NOTICE”, the word “CAUTION”

without the safety alert symbol may

be used to indicate a message not

related to personal injury.

NOTE

To ensure safe and efficient operation at all times, be sure

to follow all instructions, even if not designated as “DAN-

GER”, “WARNING” and “CAUTION".

3/18

HW1484566

DANGER

• Before operating the manipulator, make sure the servo power is

turned OFF by performing the following operations. When the servo

power is turned OFF, the SERVO ON LED on the programming

pendant is turned OFF.

– Press the emergency stop button on the programming pendant or

on the external control device, etc.

– Disconnect the safety plug of the safety fence.

(when in the play mode or in the remote mode)

If operation of the manipulator cannot be stopped in an emergency,

personal injury and/or equipment damage may result.

Fig. : Emergency Stop Button

• Before releasing the emergency stop, make sure to remove the

obstacle or error caused the emergency stop, if any, and then turn

the servo power ON.

Failure to observe this instruction may cause unintended movement of

the manipulator, which may result in personal injury.

Fig. : Release of Emergency Stop

TURN

• Observe the following precautions when performing a teaching

operation within the manipulator's operating range:

– Be sure to perform lockout by putting a lockout device on the

safety fence when going into the area enclosed by the safety

fence. In addition, the operator of the teaching operation must

display the sign that the operation is being performed so that no

other person closes the safety fence.

– View the manipulator from the front whenever possible.

– Always follow the predetermined operating procedure.

– Always keep in mind emergency response measures against the

manipulator’s unexpected movement toward a person.

– Ensure a safe place to retreat in case of emergency.

Failure to observe this instruction may cause improper or unintended

movement of the manipulator, which may result in personal injury.

• Confirm that no person is present in the manipulator's operating

range and that the operator is in a safe location before:

– Turning ON the YRC1000micro power

– Moving the manipulator by using the programming pendant

– Running the system in the check mode

– Performing automatic operations

Personal injury may result if a person enters the manipulator's

operating range during operation. Immediately press an emergency

stop button whenever there is a problem. The emergency stop button

is located on the right of the programming pendant.

• Read and understand the Explanation of the Warning Labels before

operating the manipulator.

4/18

HW1484566

DANGER

• In the case of not using the programming pendant, be sure to

supply the emergency stop button on the equipment. Then before

operating the manipulator, check to be sure that the servo power is

turned OFF by pressing the emergency stop button.

Connect the external emergency stop button to the 4-14 pin and 5-

15 pin of the Safety connector (Safety).

• Upon shipment of the YRC1000micro, this signal is connected by a

jumper cable in the dummy connector. To use the signal, make sure

to supply a new connector, and then input it.

If the signal is input with the jumper cable connected, it does not

function, which may result in personal injury or equipment damage.

WARNING

• Perform the following inspection procedures prior to conducting

manipulator teaching. If there is any problem, immediately take

necessary steps to solve it, such as maintenance and repair.

– Check for a problem in manipulator movement.

– Check for damage to insulation and sheathing of external wires.

• Return the programming pendant to a safe place after use.

If the programming pendant is left unattended on the manipulator, on a

fixture, or on the floor, etc., the Enable Switch may be activated due to

surface irregularities of where it is left, and the servo power may be

turned ON. In addition, in case the operation of the manipulator starts,

the manipulator or the tool may hit the programming pendant left

unattended, which may result in personal injury and/or equipment

damage.

5/18

HW1484566

Definition of Terms Used Often in This Manual

The MOTOMAN is the YASKAWA industrial robot product.

The MOTOMAN usually consists of the manipulator, the YRC1000micro

controller, manipulator cables, the YRC1000micro programming pendant

(optional), and the YRC1000micro programming pendant dummy

connector (optional).

In this manual, the equipment is designated as follows:

Descriptions of the programming pendant keys, buttons, and displays are

shown as follows:

Equipment Manual Designation

YRC1000micro controller YRC1000micro

YRC1000micro programming pendant Programming pendant (optional)

Cable between the manipulator

and the controller

Manipulator cable

YRC1000micro programming pendant

dummy connector

Programming pendant dummy

connector (optional)

Equipment Manual Designation

Programming

Pendant

Character Keys

/Symbol Keys

The keys which have characters or symbols

printed on them are denoted with [ ].

ex. [ENTER]

Axis Keys

/Number Keys

[Axis Key] and [Numeric Key] are generic

names for the keys for axis operation and

number input.

Keys pressed

simultaneously

When two keys are to be pressed

simultaneously, the keys are shown with a “+”

sign between them, ex. [SHIFT]+[COORD]

Mode Key Three kinds of modes that can be selected by

the mode key are denoted as follows:

REMOTE, PLAY, or TEACH

Button Three buttons on the upper side of the

programming pendant are denoted as follows:

HOLD button

START button

EMERGENCY STOP button

Displays The menu displayed in the programming

pendant is denoted with { }.

e.g. {JOB}

PC Keyboard The name of the key is denoted.

e.g. Ctrl key on the keyboard

6/18

vii

HW1484566

Description of the Operation Procedure

In the explanation of the operation procedure, the expression "Select • • • "

means that the cursor is moved to the object item and [SELECT] is

pressed, or that the item is directly selected by touching the screen.

Registered Trademark

In this manual, names of companies, corporations, or products are

trademarks, registered trademarks, or brand names for each company or

corporation. The indications of (R) and

are omitted.

7/18

Contents

viii

HW1484566

1 Outline............................................................................................................................................. 1-1

2 Group Change Instruction ............................................................................................................... 2-1

2.1 GRPCHG Instruction.......................................................................................................... 2-1

2.2 Registration of Instruction .................................................................................................. 2-2

3 Signal Allocation.............................................................................................................................. 3-1

3.1 Hand Identification Signals ................................................................................................3-1

3.2 Identification Signals for ATC Chuck/Unchuck .................................................................. 3-1

4 Job Examples.................................................................................................................................. 4-1

5 Alarm Message ............................................................................................................................... 5-1

8/18

1 Outline

1-1

HW1484566

1 Outline

The group change function attaches/detaches a tool with multiple external

axes, such as end effector, etc (hereinafter called “hand”).

The following explain how to replace the hand with external axes.

In the example below, the hand with two external axes is group S1, and

the hand with three external axes is group S2.

When the manipulator moves with the hand: S1, the job control group is

R1 + S1.

When the manipulator moves with the hand: S2, the job control group is

R1 + S2.

Fig. 1-1: Example of Group Change

YRC1000micro

Manipulator (R1)

Hand with two

external axes (S1)

Hand with three

external axes (S2)

9/18

1 Outline

1-2

HW1484566

Fig. 1-2: Hand Changed to S1 (R1+S1)

Fig. 1-3: Hand Changed to S2 (R1+S2)

Manipulator (R1)

Hand with two

external axes (S1)

Hand with three

external axes (S2)

YRC1000micro

Manipulator (R1)

Hand with two

external axes (S1)

Hand with three

external axes (S2)

YRC1000micro

10/18

Other manuals for YRC1000micro

Table of contents

Other YASKAWA Controllers manuals

YASKAWA

YASKAWA YRC1000micro User manual

YASKAWA

YASKAWA MOTOMAN DX100 User manual

YASKAWA

YASKAWA FSDrive-MV1000 Series User manual

YASKAWA

YASKAWA MP210 Series User manual

YASKAWA

YASKAWA MOTOMAN FS100 User manual

YASKAWA

YASKAWA SGD7S series User manual

YASKAWA

YASKAWA MP900 Series User manual

YASKAWA

YASKAWA A1000 Series User manual

YASKAWA

YASKAWA VS-626MT Series User manual

YASKAWA

YASKAWA CIMR-F7Z44P0 User manual

YASKAWA

YASKAWA MP2300 User manual

YASKAWA

YASKAWA MP23xxxiec Series User manual

YASKAWA

YASKAWA CC-Link User manual

YASKAWA

YASKAWA CDBR-2015B User manual

YASKAWA

YASKAWA E-7-Series SGD7S User manual

YASKAWA

YASKAWA E7 Drive User manual

YASKAWA

YASKAWA Motoman DX200 User manual

YASKAWA

YASKAWA Sigma II Series User manual

YASKAWA

YASKAWA J1000 CIMR-JC series User manual

YASKAWA

YASKAWA Varispeed f7 User manual

YASKAWA

YASKAWA mp2500 User manual

YASKAWA

YASKAWA Motoman DX200 User manual

YASKAWA

YASKAWA YRC1000 User guide

YASKAWA

YASKAWA Motoman DX200 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide