Teledyne T3PM1006 User manual

T3PM1006

Digital Power Meter

User Manual

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

This manual contains proprietary information, which is protected by

photocopied, reproduced or translated to another language without

prior written consent of Teledyne LeCroy company.

The information in this manual was correct at the time of printing.

However, Teledyne LeCroy continues to improve products and

reserves the rights to change specification, equipment, and

maintenance procedures at any time without notice.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

TABLE OF CONTENTS

Table of Contents

SAFETY INSTRUCTIONS .................................................. 5

GETTING STARTED........................................................ 10

Characteristics ............................................................11

Appearance.................................................................14

Set Up ........................................................................23

BASIC SETTING ............................................................. 26

Setting up measurement range ...................................27

Setting up measurement status ..................................31

Setting up System status ............................................41

MEASUREMENT AND OTHER FUNCTIONS .................... 46

Measurement function................................................47

Other functions ..........................................................50

Integration measurement function..............................52

REMOTE CONTROL ....................................................... 59

Configure Remote Control Interface ............................60

Return to Local Control...............................................63

COMMAND OVERVIEW ................................................. 64

Command Syntax ........................................................64

Command List ............................................................68

APPENDIX ....................................................................102

Specifications ...........................................................103

Dimensions ..............................................................108

Power measurement .................................................109

Introduction to IEC-62301.........................................111

EUP Directive Lot6 specifications .............................112

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

T3PM1006 User Manual

Connection Guide .....................................................113

CERTIFICATIONS ..........................................................115

EMC Compliance ......................................................115

Safety Compliance ....................................................117

Environmental Compliance .......................................118

RESTRICTION OF HAZARDOUS SUBSTANCES

(RoHS) .....................................................................118

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

T3PM1006 User Manual

SAFETY INSTRUCTIONS

This chapter contains important safety

instructions that you must follow during

operation and storage. Read the following before

any operation to ensure your safety and to keep

the instrument in the best possible condition.

Safety Symbols

These safety symbols may appear in this manual or on the

instrument.

WARNING

Warning: Identifies conditions or practices that

could result in injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that

could result in damage to the T3PM1006

or to other properties.

DANGER High Voltage

Attention Refer to the Manual

Protective Conductor Terminal

Earth (ground) Terminal

On (Supply)

Off (Supply)

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

T3PM1006 User Manual

Safety Guidelines

General Guideline

CAUTION

Make sure that the voltage input level does not

exceed DC848V/AC600V.

Make sure the current input level does not

exceed 20A.

Do not place any heavy object on the

instrument.

Avoid severe impact or rough handling that can

lead to damaging the instrument.

Do not discharge static electricity to the

instrument.

Use only mating connectors, not bare wires, for

the terminals.

Do not block or obstruct the cooling fan vent

opening.

Do not perform measurement at the source of a

low-voltage installation or at building

installations (Note below).

Do not disassemble the instrument unless you

are qualified as service personnel.

Make sure that the COM terminal to earth is

limited to 300Vpk.

Remove all test leads before disconnecting the

mains power cord from the socket.

If the equipment is used in a manner not

specified by the manufacturer, the protection

provided by the equipment may be impaired.

The device should be placed in a way that the

plug connected to it can be removed easily.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

SAFETY INSTRUCTIONS

(Note) EN 61010-1:2010 specifies the measurement categories and

their requirements as follows. The T3PM1006 falls under category II

300V.

Measurement category IV is for measurement performed at the

source of low-voltage installation.

Measurement category III is for measurement performed in the

building installation.

Measurement category II is for measurement performed on the

circuits directly connected to the low voltage installation.

Power Supply

WARNING

AC Input voltage: 100-240 VAC 50/60Hz

The power supply voltage should not fluctuate

more than 10%.

Connect the protective grounding conductor of

the AC power cord to an earth ground, to avoid

electrical shock.

Cleaning the

Instrument

Disconnect the power cord before cleaning.

Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid.

Do not use chemicals containing harsh material

such as benzene, toluene, xylene, and acetone.

Operation

Environment

Location: Indoor, no direct sunlight, dust free,

almost non-conductive pollution (Note below)

Temperature: 0°C to 40°C

Humidity: < 30°C: < 80%RH(non-condensing);

30°C~40°C:<70%RH(non-condensing);

>40°C: <50%RH (non-condensing)

Altitude: <2000m

(Note) EN 61010-1:2010 specifies the pollution degrees and their

requirements as follows. The T3PM1006 falls under degree 2.

Pollution refers to “addition of foreign matter, solid, liquid, or

gaseous (ionized gases), that may produce a reduction of

dielectric strength or surface resistivity”.

Pollution degree 1: No pollution or only dry, non-conductive

pollution occurs. The pollution has no influence.

Pollution degree 2: Normally only non-conductive pollution

occurs. Occasionally, however, a temporary conductivity caused

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

T3PM1006 User Manual

by condensation must be expected.

Pollution degree 3: Conductive pollution occurs, or dry, non-

conductive pollution occurs which becomes conductive due to

condensation which is expected. In such conditions, equipment

is normally protected against exposure to direct sunlight,

precipitation, and full wind pressure, but neither temperature

nor humidity is controlled.

Storage

environment

Location: Indoor

Temperature: -40°C to 70°C

Humidity: <90%RH(non-condensing)

Disposal

Do not dispose this instrument as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased. Please make sure

discarded electrical waste is properly recycled to

reduce environmental impact.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

SAFETY INSTRUCTIONS

Power cord for the United Kingdom

When using the unit in the United Kingdom, make sure the power

cord meets the following safety instructions.

NOTE: This lead/appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in accordance with the

following code:

Green/ Yellow:

Earth

Blue:

Neutral

Brown:

Live (Phase)

As the colours of the wires in main leads may not correspond with

the coloured marking identified in your plug/appliance, proceed

as follows:

The wire which is coloured Green & Yellow must be connected to

the Earth terminal marked with either the letter E, the earth symbol

or coloured Green/Green & Yellow.

The wire which is coloured Blue must be connected to the terminal

which is marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the

terminal marked with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment

or contact the supplier.

This cable/appliance should be protected by a suitably rated and

approved HBC mains fuse: refer to the rating information on the

equipment and/or user instructions for details. As a guide, a cable

of 0.75mm2should be protected by a 3A or 5A fuse. Larger

conductors would normally require 13A types, depending on the

connection method used.

Any exposed wiring from a cable, plug or connection that is

engaged in a live socket is extremely hazardous. If a cable or plug is

deemed hazardous, turn off the mains power and remove the cable,

any fuses and fuse assemblies. All hazardous wiring must be

immediately destroyed and replaced in accordance to the above

standard.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

T3PM1006 User Manual

GETTING STARTED

This chapter describes the T3PM1006, including

accessories, package contents, its main features

and front / rear panel introduction.

Characteristics ............................................................11

Accessories .............................................................................13

Package Contents ...................................................................13

Appearance .................................................................14

Front Panel..............................................................................14

Display Overview ....................................................................18

Rear Panel ...............................................................................21

Set Up.........................................................................23

Tilting the Stand......................................................................23

Power Up.................................................................................24

Connect the wires to the T3PM1006 ......................................25

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

This manual suits for next models

Table of contents

Other Teledyne Measuring Instrument manuals

Teledyne

Teledyne ADFM Pro20 User manual

Teledyne

Teledyne WIRELESS GROUNDLINK WQAR User manual

Teledyne

Teledyne CP Series User manual

Teledyne

Teledyne SeaBat T Series User manual

Teledyne

Teledyne ULTRAFLOW 150 User manual

Teledyne

Teledyne N500 User manual

Teledyne

Teledyne HASTINGS 200 Series User manual

Teledyne

Teledyne HVG-2020A User manual

Teledyne

Teledyne HASTINGS Everywhereyoulook 201 Series User manual

Teledyne

Teledyne T300 User manual

Teledyne

Teledyne 300M User manual

Teledyne

Teledyne T101 User manual

Teledyne

Teledyne 9110AH User manual

Teledyne

Teledyne 2150EX Operating instructions

Teledyne

Teledyne GMI PS200 User manual

Teledyne

Teledyne PS200 Series Manual

Teledyne

Teledyne HVG-2020B User manual

Teledyne

Teledyne 235 User manual

Teledyne

Teledyne 100E User manual

Teledyne

Teledyne BOSON+ CZ 14-75 User manual

Teledyne

Teledyne AX300 User manual

Teledyne

Teledyne PEM-9004 User manual

Teledyne

Teledyne Princeton Instruments FER785-MM User manual

Teledyne

Teledyne T102 User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual