Sper scientific 840006 User manual
Light Meter (Lux)
840006
Instruction Manual
2 PB
TABLE OF CONTENTS
1. INTRODUCTION........................................................................................ 2
2. PANEL DESCRIPTION.............................................................................. 2
3. MEASUREMENT PROCEDURES............................................................ 3
4. ZERO ADJUSTMENT & CALIBRATION................................................... 3
5. BATTERY REPLACEMENT ...................................................................... 4
6. SPECIFICATIONS...................................................................................... 4
7. LIGHT SPECTRUM CHART................................................................... 4
8. WARRANTY……………………………………………………. ................... 4
1. INTRODUCTION
Compact and portable, your new meter can be used to monitor light levels
or check the LUX level of a particular light source. The sensor’s exclusive
photo diode and color correction lter meets the C.I.E. photopic spectrum
with a cosine correction factor meets the standard. Sper Scientic light
meters are cosine corrected for a quick and accurate response. Large
easily legible LCD. The meter has an external zero adjustment, data hold,
low-battery indicator, and a moisture resistant front panel. Comes with soft
carrying case, detachable light sensor, photo-sensor cover, instructions
and a 9-Volt battery.
2. PANEL DESCRIPTION
1
2
3
4
6
5
laboratory calibration only
7
10
12
11
9
8
1. DISPLAY 5. X1 (2,000 RANGE) button 9. STAND
2. ON button 6. X10 (20,000 RANGE) button 10. BATTERY
3. OFF button 7. ZERO SETTING terminal 11. PHOTO SENSOR
4. HOLD button 8. SENSOR INPUT socket 12. SENSOR plug
3 PB
3. MEASUREMENT PROCEDURES
• Insert the SENSOR plug into the SENSOR INPUT socket.
• Turn the meter on using the ON button.
• Remove the lens cap from the PHOTO SENSOR.
• Press the 1X button for measurements of 0 to 1999 LUX, or select
the 10X button for measurements of 2,000 to 19,990 LUX. If you are
uncertain about which range to use, select the highest range.
In 10X mode, “ “ appears in the right bottom LCD.
• Range Overload is indicated when “1” appears on the left side of the
display. If this occurs, switch to the highest range or discontinue use.
• Point the PHOTO SENSOR toward the source and read the results
on the display. To convert LUX results to FC, multiply the meter
reading by the factor of .0929
• Push the HOLD button to freeze the reading in the display. The word
“HOLD” is displayed. Press the HOLD button again to exit this function.
• Press the OFF button to turn the unit o.
NOTES:
• Keep the lens cap on the PHOTO SENSOR at all times except when
actually taking a reading.
• Fluctuations in the reading are generally due to shadows or
uctuations in the line voltage. Ambient temperature, drafts and
ventilation also aect the luminous ux output.
• Avoid range overload and do not store in areas of high temperature
and/or humidity. Remove the battery for long-term storage.
4. ZERO ADJUSTMENT & CALIBRATION
• With the sensor cover securely in place and the meter turned on, the
LCD display should indicate “0000”. A slight variation will not aect
readings; however, if a precise reading is required you may use the
ZERO SETTING terminal to reset the unit.
• To make an adjustment, cover the PHOTO SENSOR and press
the 1X button.
• Use a small screwdriver to turn the ZERO SETTING terminal until
“0000” is displayed.
• To maintain accuracy, annual laboratory calibration is recommended.
WARNING: Only use the terminal marked "ZERO" for adjustment.
The unmarked terminals are for professional laboratory calibration only
and tampering with these terminals will result in inaccurate readings
and require professional calibration of the meter.
4 PB
8. WARRANTY
Sper Scientic warrants this product against
defects in materials and workmanship for
a period of ve (5) years from the date of
purchase, and agrees to repair or replace
any defective unit without charge. If your
model has since been discontinued, an
equivalent Sper Scientic product will
be substituted if available. This warranty
does not cover probes, batteries, battery
leakage, or damage resulting from accident,
tampering, misuse, or abuse of the product.
Opening the meter to expose its electronics
will break the waterproof seal and void the
Revised 8/17/2017
5. BATTERY REPLACEMENT
Replace the battery when the low battery icon is displayed in the
left corner of LCD. In-spec measurements may be made for several hours
after the low battery indicator appears. Remove the battery compartment
screw and slide the cover away from the meter, remove the battery and
replace with a 9V battery (alkaline or heavy duty type). Replace the cover.
6. SPECIFICATIONS
7. LIGHT SPECTRUM CHART
0
20
40
60
80
10 0
12 0
4
1
0
4
3
0
4
5
0
4
7
0
4
9
0
5
1
0
5
3
0
5
5
0
5
7
0
5
9
0
6
1
0
6
3
0
6
5
0
6
7
0
6
9
0
7
1
0
7
3
0
7
5
0
SPER CEI
Display Maximum reading 19,990
Overload Indicator "1" is displayed on the le of the LCD
Range* 2,000 Range = 0 to 1,999 LUX
20,000 Range = 2,000 to 19,990 LUX
Resolution* 2,000 Range = 1 LUX
20,000 Range = 10 LUX
Accuracy* ±5% + 4 digits
Operating Environment 32 to 122°F (0 to 50°C), less than 80% RH
Weight 9.9 oz (280g)
Dimensions Main Unit: 7.9 x 2.7 x 1.2" (200 x 68 x 30mm)
Photo Sensor: 3.2 x 2.2 x 0.3” (82 x 55 x 7mm)
Photo Sensor Lead: Extends to appx. 3½
Optional Accessories 840090 - Water Resistant Instrument Pouch
840093 Field Tripod
*Electronic Specications (23 ± 5°C): Tested under the environment RF Field Strength
less than 3 V/M, and frequency less than the 30 MHz only.
warranty. To obtain warranty service, ship the unit postage prepaid to:
SPER SCIENTIFIC LTD., 8281 E. Evans Rd., Suite #103,
Scottsdale, AZ 85260, (480) 948-4448
The defective unit must be accompanied by a description of the problem and your
return address. Register your product online at
www.sperwarranty.com within 10 days of purchase.
Table of contents
Other Sper scientific Measuring Instrument manuals
Sper scientific
Sper scientific 840065 User manual
Sper scientific
Sper scientific 300058 User manual
Sper scientific
Sper scientific 300107 User manual
Sper scientific
Sper scientific 840015 User manual
Sper scientific
Sper scientific 850048 User manual
Sper scientific
Sper scientific 860041 User manual
Sper scientific
Sper scientific 850006 Installation and user guide
Sper scientific
Sper scientific 850025 User manual
Sper scientific
Sper scientific 850026 User manual
Sper scientific
Sper scientific 840023 User manual
Sper scientific
Sper scientific 850004 User manual
Sper scientific
Sper scientific 800020 User manual
Sper scientific
Sper scientific 850039 User manual
Sper scientific
Sper scientific 840012 User manual
Sper scientific
Sper scientific 840024 User manual
Sper scientific
Sper scientific 850001E User manual
Sper scientific
Sper scientific 801038 User manual
Sper scientific
Sper scientific 850050 User manual
Sper scientific
Sper scientific 850013 User manual
Sper scientific
Sper scientific 850068 User manual
