Siemens NIM-1W User manual

Figure 1

NIM-1W Module Board (RS485 setting)

The NIM-1W supports both Style 4 and Style 7

connection. In the event of an NIM-1W communica-

tion failure, each MXL System continues to operate

as a standalone panel.

The NIM-1W can also be configured as an RS-485

two wire interface to foreign systems. NIM-1W

RS485 only supports Style 4 wiring. Via the add-on

modem card NIM-1M, NIM-1W can also be config-

ured for modem connection. This operation is called

FSI (Foreign System Interface). The FSI responds

to a protocol and gathers information about the MXL

status. The interface supports both single MXL

Systems and networked systems. Typical use of

this interface is between the MXL and building

management systems.

Use the CSG-M to enable the functions accessed

by the foreign system. If the foreign system is UL

864 listed with the MXL, the interface can also be

enabled to support control of the MXL including the

commands to acknowledge, silence, and reset.

OPERATION

The Model NIM-1W from Siemens Industry, Inc.,

provides a new communication path for the following

uses:

• as an XNET networking interface

• as an HNET connection to NCC WAN

• as a connection to Foreign Systems

• as a connection to Air Sampling detectors

When used as an XNET networking interface the

NIM-1W allows for the connection of up to 63 MXL

and/or XLS Systems. On an XNET network the NIM-

1W also supports monitor and control functionality by

Siemens products, such as NCC and Desigo CC.

Output logic between MXL panels is done using

CSG-M programming. CSG-M versions 6.01 and

higher include options for networked MXL Systems.

Each MXL System is assigned a panel number. This

panel number allows interactive programming be-

tween panels using CSG-M.

NIM-1W

JP2

JP1

D4 D5 D8

SW1

SW2

113

87654321

–

ANY

TRBL

ANY

ENABLE XMIT

INSTALL JUMPER PLUGS IN

ORIENTATION AS SHOWN

FOR RS485 WIRING.

POSITION SHOWN

SELECTED.

JP4

INSTALL JUMPER

PLUGS IN ORIENTATION

AS SHOWN. POSITION

SHOWN SELECTED.

JP4

13 15

Installation Instructions

Model NIM-1W Network Interface Module

NETWORK INTERFACEAPPLICATIONS

P/N 315-099165-10

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Canada Limited

Building Technologies Division

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 Canada

NIM-1W

JP2

JP1

D4 D5 D8

SW1

SW2

113

87654321

–

ANY

TRBL

ANY

ENABLE XMIT

INSTALL JUMPER PLUGS IN

ORIENTATION AS SHOWN

FOR MODEM.

JP4

INSTALL JUMPER

PLUGS IN ORIENTATION

AS SHOWN. POSITION

SHOWN SELECTED.

JP4

13 15

Figure 2

NIM-1W Module Board (modem setting)

TABLE 1

NETWORK ADDRESS PROGRAMMING (SW1)

ADDR 87654321 ADDR 87654321 ADDR 87654321 ADDR 87654321

000 ILLEGAL 064 OXOOOOOO 128 XOOOOOOO 192 XXOOOOOO

001 ILLEGAL 065 OXOOOOOX 129 XOOOOOOX 193 XXOOOOOX

002 ILLEGAL 066 OXOOOOXO 130 XOOOOOXO 194 XXOOOOXO

003

004

005

006

007

008

009

010

011

012

013

014

015

016

017

018

019

020

021

022

023

024

025

026

027

028

029

030

031

032

033

034

035

036

037

038

039

040

041

042

043

044

045

046

047

048

049

050

051

052

053

054

055

OOOOOOXX

OOOOOXOO

OOOOOXOX

OOOOOXXO

OOOOOXXX

OOOOXOOO

OOOOXOOX

OOOOXOXO

OOOOXOXX

OOOOXXOO

OOOOXXOX

OOOOXXXO

OOOOXXXX

OOOXOOOO

OOOXOOOX

OOOXOOXO

OOOXOOXX

OOOXOXOO

OOOXOXOX

OOOXOXXO

OOOXOXXX

OOOXXOOO

OOOXXOOX

OOOXXOXO

OOOXXOXX

OOOXXXOO

OOOXXXOX

OOOXXXXO

OOOXXXXX

OOXOOOOO

OOXOOOOX

OOXOOOXO

OOXOOOXX

OOXOOXOO

OOXOOXOX

OOXOOXXO

OOXOOXXX

OOXOXOOO

OOXOXOOX

OOXOXOXO

OOXOXOXX

OOXOXXOO

OOXOXXOX

OOXOXXXO

OOXOXXXX

OOXXOOOO

OOXXOOOX

OOXXOOXO

OOXXOOXX

OOXXOXOO

OOXXOXOX

OOXXOXXO

OOXXOXXX

067

068

069

070

071

072

073

074

075

076

077

078

079

080

081

082

083

084

085

086

087

088

089

090

091

092

093

094

095

096

097

098

099

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

OXOOOOXX

OXOOOXOO

OXOOOXOX

OXOOOXXO

OXOOOXXX

OXOOXOOO

OXOOXOOX

OXOOXOXO

OXOOXOXX

OXOOXXOO

OXOOXXOX

OXOOXXXO

OXOOXXXX

OXOXOOOO

OXOXOOOX

OXOXOOXO

OXOXOOXX

OXOXOXOO

OXOXOXOX

OXOXOXXO

OXOXOXXX

OXOXXOOO

OXOXXOOX

OXOXXOXO

OXOXXOXX

OXOXXXOO

OXOXXXOX

OXOXXXXO

OXOXXXXX

OXXOOOOO

OXXOOOOX

OXXOOOXO

OXXOOOXX

OXXOOXOO

OXXOOXOX

OXXOOXXO

OXXOOXXX

OXXOXOOO

OXXOXOOX

OXXOXOXO

OXXOXOXX

OXXOXXOO

OXXOXXOX

OXXOXXXO

OXXOXXXX

OXXXOOOO

OXXXOOOX

OXXXOOXO

OXXXOOXX

OXXXOXOO

OXXXOXOX

OXXXOXXO

OXXXOXXX

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

XOOOOOXX

XOOOOXOO

XOOOOXOX

XOOOOXXO

XOOOOXXX

XOOOXOOO

XOOOXOOX

XOOOXOXO

XOOOXOXX

XOOOXXOO

XOOOXXOX

XOOOXXXO

XOOOXXXX

XOOXOOOO

XOOXOOOX

XOOXOOXO

XOOXOOXX

XOOXOXOO

XOOXOXOX

XOOXOXXO

XOOXOXXX

XOOXXOOO

XOOXXOOX

XOOXXOXO

XOOXXOXX

XOOXXXOO

XOOXXXOX

XOOXXXXO

XOOXXXXX

XOXOOOOO

XOXOOOOX

XOXOOOXO

XOXOOOXX

XOXOOXOO

XOXOOXOX

XOXOOXXO

XOXOOXXX

XOXOXOOO

XOXOXOOX

XOXOXOXO

XOXOXOXX

XOXOXXOO

XOXOXXOX

XOXOXXXO

XOXOXXXX

XOXXOOOO

XOXXOOOX

XOXXOOXO

XOXXOOXX

XOXXOXOO

XOXXOXOX

XOXXOXXO

XOXXOXXX

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

XXOOOOXX

XXOOOXOO

XXOOOXOX

XXOOOXXO

XXOOOXXX

XXOOXOOO

XXOOXOOX

XXOOXOXO

XXOOXOXX

XXOOXXOO

XXOOXXOX

XXOOXXXO

XXOOXXXX

XXOXOOOO

XXOXOOOX

XXOXOOXO

XXOXOOXX

XXOXOXOO

XXOXOXOX

XXOXOXXO

XXOXOXXX

XXOXXOOO

XXOXXOOX

XXOXXOXO

XXOXXOXX

XXOXXXOO

XXOXXXOX

XXOXXXXO

XXOXXXXX

XXXOOOOO

XXXOOOOX

XXXOOOXO

XXXOOOXX

XXXOOXOO

XXXOOXOX

XXXOOXXO

XXXOOXXX

XXXOXOOO

XXXOXOOX

XXXOXOXO

XXXOXOXX

XXXOXXOO

XXXOXXOX

XXXOXXXO

XXXOXXXX

XXXXOOOO

XXXXOOOX

XXXXOOXO

XXXXOOXX

XXXXOXOO

XXXXOXOX

XXXXOXXO

XXXXOXXX

056 OOXXXOOO 120 OXXXXOOO 184 XOXXXOOO 248 ILLEGAL

057 OOXXXOOX 121 OXXXXOOX 185 XOXXXOOX 249 ILLEGAL

058 OOXXXOXO 122 OXXXXOXO 186 XOXXXOXO 250 ILLEGAL

059 OOXXXOXX 123 OXXXXOXX 187 XOXXXOXX 251 ILLEGAL

060 OOXXXXOO 124 OXXXXXOO 188 XOXXXXOO 252 ILLEGAL

061 OOXXXXOX 125 OXXXXXOX 189 XOXXXXOX 253 ILLEGAL

062 OOXXXXXO 126 OXXXXXXO 190 XOXXXXXO 254 ILLEGAL

063 OOXXXXXX 127 OXXXXXXX 191 XOXXXXXX 255 ILLEGAL

O = OPEN (or OFF) X = CLOSED ( or ON)

Setting the Switches

Set all switches, configuration jumpers, and

connection cables before installing the NIM-1W

into the MOM-4.

Use switch SW1 to set the MXL network address. Set

this switch according to the address where the NIM-1W

is installed in the MXL’s network map. Refer to the

CSG-M configuration printout for the address of the

module. See Table 1 for settings.

Use switch SW2 to set either the panel number for

networked systems or to select FSI or Air Sampling

operation. Refer to Table 2 for panel settings, Table 3

for FSI settings, and Table 4 for Air Sampling settings.

1. When installing the NIM-1W in a networked

system, set the panel number to agree with the

panel number for the NIM-1W assigned to the

MXL System in CSG-M.

2. Switch position 8 selects Style 4 or Style 7

operation for the NIM-1W network.

3. Set jumper plugs on JP4 to the "M" position.

4. Set jumper plugs on P6 to the "X" position (Figure

1) if using NIM-1W for RS-485 interface. Set

jumper plugs on P6 as shown in Figure 2 if using

NIM-W for modem interface.

NOTE:

To open a dipswitch, press down on the side of the dipswitch marked OPEN.

To close a dipswitch, press down on the side of the dipswitch opposite the side marked OPEN.

To open a slide switch, push the slide to the side opposite the side marked ON.

To close a slide switch, push the slide to the side marked ON.

TABLE 2

PANEL NUMBER PROGRAMMING (SW2)

ADDR 8 7 6 5 4 3 2 1 ADDR 8 7 6 5 4 3 2 1 ADDR 8 7 6 5 4 3 2 1 ADDR 8 7 6 5 4 3 2 1

000

001

002

003

004

005

006

007

008

009

010

011

012

013

014

015

---

ROOOOOOO

SOOOOOOX

SOOOOOXO

SOOOOOXX

SOOOOXOO

SOOOOXOX

SOOOOXXO

SOOOOXXX

SOOOXOOO

SOOOXOOX

SOOOXOXO

SOOOXOXX

SOOOXXOO

SOOOXXOX

SOOOXXXO

SOOOXXXX

---------------

016

017

018

019

020

021

022

023

024

025

026

027

028

029

030

031

---

SOOXOOOO

SOOXOOOX

SOOXOOXO

SOOXOOXX

SOOXOXOO

SOOXOXOX

SOOXOXXO

SOOXOXXX

SOOXXOOO

SOOXXOOX

SOOXXOXO

SOOXXOXX

SOOXXXOO

SOOXXXOX

SOOXXXXO

SOOXXXXX

---------------

032

033

034

035

036

037

038

039

040

041

042

043

044

045

046

047

---

SOXOOOOO

SOXOOOOX

SOXOOOXO

SOXOOOXX

SOXOOXOO

SOXOOXOX

SOXOOXXO

SOXOOXXX

SOXOXOOO

SOXOXOOX

SOXOXOXO

SOXOXOXX

SOXOXXOO

SOXOXXOX

SOXOXXXO

SOXOXXXX

--------------

048

049

050

051

052

053

054

055

056

057

058

059

060

061

062

063

064

SOXXOOOO

SOXXOOOX

SOXXOOXO

SOXXOOXX

SOXXOXOO

SOXXOXOX

SOXXOXXO

SOXXOXXX

SOXXXOOO

SOXXXOOX

SOXXXOXO

SOXXXOXX

SOXXXXOO

SOXXXXOX

SOXXXXXO

SOXXXXXX

SXOOOOOO

S = Closed selects Style 7

S = Open selects Style 4

O = Open or OFF

X = Closed or ON

R = Closed selects AnaLASER

R = Open selects FSI

The NIM-1W also provides for the connection of up to

31 Air Sampling detectors. The MXL supports indi-

vidual programming and monitoring of the Air Sam-

pling devices. Each detector can be uniquely pro-

grammed from the MKB menu or by using CSG-M. All

three alarm levels (PreAlarm 1, PreAlarm 2, and

Alarm) are supported.

NOTE: When the NIM-1W is configured as an Air

Sampling interface, it cannot support either

MXL networking or the FSI. If these functions

are required, additional NIM-1Ws must be

used.

For additional information on the MXL/MXLV System,

refer to the MXL/MXLV Manual, P/N 315-092036.

INSTALLATION

Remove all system power before installation,

first battery and then AC. (To power up, con-

nect the AC first, then the battery.)

The NIM-1W installs into the MXL optional MOM-4/2

card cage where it occupies one full width slot. The

NIM-1W can be installed in either of the full slots of the

MOM-4/2.

The slot determines if the wiring is con-

nected to TB3 or TB4 of the MOM-4/2.

Figure 3

NIM-1W Network Wiring Diagram

After setting the switches, install the NIM-1W into the

MOM-4/2 card cage. Make sure that the module is in

the card guides and the card edge is firmly seated in the

connectors on the MOM-4/2

CAUTION

At all times handle all plug-in cards with extreme

care. When inserting or removing a card, be sure the

position of the card is kept at right angles to the

MOM-4 board. Otherwise, the plug-in card can

damage or displace other components.

5. When installing the NIM-1W for FSI operation, set

the switch to all open (or OFF).

TABLE 3

FSI PROGRAMMING

ADDR 8 7 6 5 4 3 2 1

FSI OOOOOOOO

O = Open or OFF

6. When installing the NIM-1W for Air Sampling

detection connection, set the switch as follows:

4ELBAT

GNILPMASRIAGNIMMARGORP

RDDA12345678

gnilpmaSriAOOOOOOOX

FFOronepO=O

NOrodesolC=X

EOLR 120 OHMS, 1/4W

P/N 140-820150

EOLR 120 OHMS, 1/4W

P/N 140-820150

CABLE P/N 555-190967

TO MMB OR PSR-1

DO NOT USE

SEE FIGURE 4

TB1

345678910111213141516

TB3

NIM-1W

TB2 TB4

INSTALLED IN MXL PANEL 3

345678910111213141516

MOM-4

910111213141516

12345678

NETWORK PAIR B

SUPERVISED (OMIT FOR STYLE 4)

REQUIRED IN CANADIAN INSTALLATIONS

NETWORK PAIR A

SUPERVISED

EOLR 120 OHMS, 1/4W

P/N 140-820150

EOLR 120 OHMS, 1/4W

P/N 140-820150

CABLE P/N 555-190967

TO MMB OR PSR-1

CABLE P/N 555-190967

TO MMB OR PSR-1

DO NOT USE DO NOT USE DO NOT USE

DO NOT USE

SEE FIGURE 4 SEE FIGURE 4

TB1 TB1

P1 P1

P7 P7

345678910111213141516

P3 P3

TB3 TB3

NIM-1W NIM-1W

TB2 TB2

TB4 TB4

INSTALLED IN MXL PANEL 1

345678910111213141516

MOM-4

INSTALLED IN MXL PANEL 2

345678910111213141516

MOM-4

17 18 19 20 21 22 23 24

SEE NOTE 9 DO NOT USE

DO NOT USE

ONE SLOT OF CC-5

NIC-C

(IF USED)

NOTES:

1. 18 AWG minimum.

2. 80 ohms maximum per pair.

3. Use shielded twisted pair.

4. Terminate the shield at MXL Panel 1

only.

5. Power limited to NFPA 70 per NEC 760.

6. Maximum voltage 8V peak to peak.

7. Maximum current 150mA.

8. For Style 4 omit all Network Pair B

connections.

9. CC-5 terminals 9-14 are not connected

and can be used to tie shields together.

10. Refer to Wiring Specification for MXL,

MXL-IQ and MXLV Systems, P/N 315-

092772 revision 6 or higher, for addi-

tional wiring information.

GROUND FAULT DETECTED AT <70K OHMS FOR TERMINALS 1-4.

Figure 4

Connecting the NIM-1W to the NCC/Desigo CC and FireFinder-XLS

ELECTRICAL CONNECTIONS

NIM-1W On An XNET Network

Figure 3 shows the wiring diagram for the NIM-1W on

an XNET network. Up to 32 MXL and/or XLS Sys-

tems can be connected in the XNET network with an

NIM-1W installed in each MXL System. For the

highest level of fault protection, install the NIM-1W in

the enclosure with the MMB, although this is not

necessary. When connecting more than 32 MXL

Systems, an REP-1 repeater, a D2300CPS or a

D2325CPS is required. Refer to the REP-1 Installa-

tion Instructions, P/N 315-092686, the D2300CPS

Installation Instructions, P/N 315-050018 or the

D2325CPS Installation Instructions, P/N 315-050019,

as applicable, for the wiring diagram.

The XNET network can be installed as either Style 4

or Style 7. Figure 3 shows which wires must be added

to support Style 7. Style 7 is required in Canada.

Each NIM-1W is shipped with two 120 ohm EOLRs—

only two are required for each network pair. Install an

EOLR at the ends of each network pair. Do not

install an EOLR at each NIM-1W. (A simple rule of

NOTES:

1. No EOLR required for NIC-C.

2. The screw terminals can accommodate one 12-24AWG or two 16-

24AWG.

3. From the NCC-2F to NIM-1R, NIM-1W or NCC-2F:

80 Ohms max. per pair.

Unshielded twisted pair - .5μF line to line

Shielded twisted pair - .3μF line to line, .4μF line to shield

thumb for the NIM-1W: an EOLR must be installed

where only a single wire lands on a screw terminal.)

Do not T-tap the network wiring. If T-tapping is

required, use the REP-1 repeater. Refer to the REP-1

Installation Instructions, P/N 315-092686, the

D2300CPS Installation Instructions, P/N 315-050018

or the D2325CPS Installation Instructions, P/N 315-

050019, as applicable, for the wiring diagram.

For Style 4 wiring, terminate the secondary network

pair (terminals 3 and 4) on each NIM-1W with an

EOLR.

Network Command Center (NCC/Desigo CC)

Figure 4 shows the wiring to the NCC/Desigo CC.

To connect the NCC/Desigo CC, observe the following

restrictions:

1. Give the NCC/Desigo CC a panel number. (This

panel number is in addition to the panel number

for the MXL System that the NCC/Desigo CC

connects to.)

2. The total number of panels in the XNET must not

exceed 64, including the NCC/Desigo CC.

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

17 18 19 20 21 22 23 24

SEE NOTE 7

(MUST BE IN SAME ENCLOSURE AS THE PMI)

DO NOT USE

DO NOT USE DO NOT USE

ONE SLOT OF CC-5

NIC-C

1 2 3 4 5

PAIR A

SUPERVISED

POWER LIMITED

PAIR B

(OMIT FOR STYLE 4)

SUPERVISED

POWER LIMITED

LOCATED INSIDE NCC/

DESIGO CC/VNT

NOTE:

IF THE NCC/DESIGO CC/VNT

IS LOCATED AT THE END OF THE

XNET NETWORK, INSTALL EOLR

P/N 140-820350 ACROSS

TERMINALS 1 & 2 AND 3 & 4.

NCC-2F MOM-4

TB3 OR TB4

NIM-1R / NIM-1W

1234

TO ADDITIONAL

NIM-1Rs, NIM-1Ws,

NCC-2Fs OR NIC-C

4. From the NCC-2F to NIC-C:

2000 feet (33.8 ohms) max. per pair between CC-5s/CC-2s.

Unshielded twisted pair

.25μF max. line to line

Shielded twisted pair

.15μF max. line to line

.2μF max. line to shield

5. Use twisted pair or twisted shielded pair.

6. Terminate shields at one end only.

7. Power limited to NFPA 70 per NEC 760.

8. CC-5 terminals 9 - 14 are not connected and can be used to tie shields

together.

9. Positive or negative ground fault detected at <10K ohms on pins 3-4,

7-8 of the NIC-C.

10. Each pair independently supervised.

11. Maximum voltage 8V P-P.

12. Maximum current 75mA during message transmission.

Figure 5

Connecting the NIM-1W (with RS-485 interface) to the FSI

EOLR

120 OHMS, 1/2W

P/N 140-099066

DO NOT USE

CABLE P/N 555-190967

TO MMB, SMB

OR PSR-1

TO MMB, SMB OR PSR-1

24V

TB1

TB2

TB3

TB4

5678910111213141516

EOLR

120 OHMS, 1/2W

P/N 140-099066

EOLR

120 OHMS, 1/2W

P/N 140-099066

CONNECT ONLY TO

UL EDP OR ETI

LISTED EQUIPMENT

SUPERVISED

FOREIGN SYSTEM RS-485 INTERFACE

TRANSMIT ENABLE

TRANSMIT

RECEIVE

DO NOT USE

MOM-4

NIM-1W

P10

P8 TB7

NOTES:

1. 18 AWG minimum.

2. 80 ohms maximum per pair.

3. Use shielded twisted pair.

4. Terminate the shield at the NIM-1W enclosure only.

5. Power limited to NFPA 70 per NEC 760.

6. Maximum voltage 8V peak to peak.

7. Maximum current 150mA.

8. Refer to Wiring Specification for MXL, MXL-IQ and

MXLV Systems, P/N 315-092772 revision 6 or

higher, for additional wiring information.

Foreign System Interface (FSI)

The FSI installs on TB3 or TB4, terminals 1 and 2, of

the MOM-4/2 depending on where the NIM-1W is

installed, as shown in Figure 5. Use one of the EOLRs

provided with the NIM-1W on terminals 1 and 2. This

properly terminates the FSI. Use the second EOLR on

terminals 3 and 4. Never use terminals 3 and 4 to

connect to the FSI. Refer to Figure 5 for the polarity

of the FSI driver.

If multiple FSI connections are required, up to four

NIM-1Ws may be installed in an individual MXL

System. In networked systems each MXL can support

up to four FSI ports.

For networked systems, each FSI port must be con-

figured as either local or global in the CSG-M. Local

FSI ports display information only on the MXL System

to which they are connected. Global FSI ports display

all events in all MXL Systems. Refer to the CSG-M

Manual, P/N 315-090381, for further information.

Connection via NIM-1W RS-485 Interface

NIM-W RS485 FSI connection should be wired Style 4

only. The recommended Serial Baud Rate when using

NIM-1W RS485 FSI is 19200 bpm. P6 jumper position

on the NIM-1W should be set for RS-485 configura-

tion as shown in Figure 1. Refer to Figure 5 for wiring

instructions.

Connection via NIM-1W/NIM-1M Modem

NIM-1W/NIM-1M modem FSI connection should be

wired Style 4 only. P6 jumper position on the NIM-1W

should be set for Modem configuration as shown in

Figure 2. The recommended Serial Baud Rate when

using NIM-1W/NIM-1M Modem FSI is 19200 bpm.

Refer to Figure 16 for wiring instructions.

Air Sampling Interface

AnaLASER Interface

The AnaLASER Air Sampling interface connects to the

MOM-4/2, TB3 or TB4, terminals 1 and 2, depending

on where the NIM-1W is installed (Refer to Figure 7).

Up to 31 Air Sampling detectors can be connected to

a single NIM-1W.

The ACC-1 requires an RS-485 to RS-232 converter

which mounts in the back of the ACC-1 enclosure. The

converter model number is AIC-4Z. The AIC-4Z

supports from one to four AnaLASER detectors. Refer

to the AIC-4Z Installation Instructions, P/N 315-

093792, for the mounting and configuration of the

converter and the ACC-1s.

Complete wiring of the converter as shown in Figure 7

before installing the ACC-1 in the enclosure.

• Place the end-of-line resistors in the locations

specified in Figure 7.

• Install the cable P/N IC-12 between the converter

and the ACC-1.

• Refer to the AnaLASER Air Sampling Smoke

Detection Manual, P/N 315-092893, for connec-

tion to the AnaLASER detector and power supply,

as well as mechanical mounting of the ACC-1.

GROUND FAULT DETECTED AT <70K OHMS FOR TERMINALS 1-4.

VESDA Interface

The VESDA Air Sampling interface connects to the

MOM-4/2, TB3 or TB4, terminals 12-16, depending on

where the NIM-1W is installed (Refer to Figure 8). Up

to 31 Air Sampling detectors can be connected to a

single NIM-1W.

The VESDA/MXL-IQ Intelligent Interface requires a

model CPY-HLI which consists of an MXL-IQ/VESDA

High Level Interface and a VESDAnet Socket. The

CPY-HLI can support up to 31 VESDA detectors

utilizing a VESDA network. Refer to the CPY-HLI

Installation Instructions, P/N 315-099200, for mount-

ing and installation of the CPY-HLI to the VESDA

detectors.

Complete wiring of the Intelligent Interface as shown

in Figure 8.

• Place the end-of-line resistors in the locations

specified in Figure 8.

• Install the 5 leads of the Model CPY-HLICABLE

interface cable (P/N 500-699911) to the MOM-4/2

according to the CPY-HLI Installation Instructions,

P/N 315-099200. (Refer to Figure 8.)

• To connect the CPY-HLI to the VESDA network,

refer to the CPY-HLI Installation Instructions, P/N

315-099200.

NOTE: VESDA is supported in NIM-1W firmware

version 2.0 and higher, SMB ROM version 6.10 and

higher and CSG-M version 11.01 and higher.

ELECTRICAL RATINGS

tnerruCeludoMCDV5evitcAAm0

tnerruCeludoMCDV42evitcAAm06

tnerruCeludoMCDV42ybdnatSAm06

1231234567 8

9 10 1112 131415 16

17 18 19 20 21 22 23 24

ONE SLOT OF CC-5 #1 WITH HUB-4

INSTALLED

AAAABB BB

++ --++ --

AABB

++ --

PSC-12

TB4+-

TB1

TB2

LLM-1

12 34

AABB

++ --

MODEM OR

OR RS-485

INTERFACE

Port #3

MODEM OR

OR RS-485

INTERFACE

Port #4

Power limited to NFPA 72 per NEC 760

Shield

MODEM

JP1

JP3

JP2

FSK @ 19.2kbps

Transmit level : 10Dbm

Receive level: 43 Dbm

MODEM OR

OR RS-485

INTERFACE

Port #2

Refer to NIM-1M instructions, P/N 315-099105 for

configuration settings and specific wiring guidelines

NIM-1M Module

Board

* The LLM-1 inserts

10 ohms between

TB1 and TB2

terminals 2 and 3

(20 ohms total).

Install the LLM-1 in the MXL enclosure.

Modem Ratings

14-18 AWG 10 miles Max.

20 AWG 6 miles Max.

22 AWG 4 miles Max.

0.8 uf max line to line

14-22 AWG unshielded twisted pair

The interface type

(Modem or RS-485)

must match on each

COM-2 card. If only

one interface is used

on a COM-2 card, it

must be placed on

Port #1 or Port #3

NCC-WAN

Chassis

Ground

Positive or negative ground fault detected <5K ohm

on CC-5 1-16

Figure 6

Connecting HUB-4 to NIM-1W with Modem Block

P/N 315-099165-10

Document ID A6V10239281

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Canada Limited

Building Technologies Division

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 Canada

MODEL CPY-HLICABLE (P/N 500-699911) Requirements:

1. 18 AWG minimum.

2. Maximum distance between MXL-IQ and CPY-HLI

enclosures is 6 feet.

3. Cable must be in rigid conduit and can not leave the room.

4. Shielded cable is not recommended.

5. Power limited to NFPA 70 per NEC Article 760.

REFER TO THE CPY-HLI INSTALLATION INSTRUCTIONS, P/N 315-099200,

FOR MOUNTING AND INSTALLATION OF THE MODEL CPY-HLI TO THE

VESDA DETECTORS.

CPY-HLI

PCB

CPY-HLI

PCB

V’net

VESDAnet

Socket

VESDAnet

Socket

MOM-4

NIM-1W

CABLE P/N 555-190967

TO SMB

24V

MODEL CPY-HLICABLE

P/N 500-699911

E.O.L.R.

120 OHMS, 1/2 W,

P/N 140-099066

E.O.L.R.

120 OHMS, 1/2 W,

P/N 140-099066

DO NOT USE

RS-232 PORT

7 8 9 10111213141516

TB3

TB6

123456

SUPERVISED

BLACK

BROWN

GREEN

RED

WHITE

Figure 8

Connecting the NIM-1W to the CPY-HLI

REFER TO WIRING SPECIFICATION FOR MXL, MXL-IQ AND MXLV SYSTEMS,

P/N 315-092772 REVISION 6 OR HIGHER, FOR ADDITIONAL WIRING

INFORMATION.

NOTES:

1. 18 AWG minimum.

2. 80 ohms maximum per pair.

3. Use twisted pair or shielded twisted pair.

4. Terminate the shield at the NIM-1W enclosure only.

5. Power limited to NFPA 70 per NEC 760.

6. Maximum voltage 8V peak to peak.

7. Maximum current 150mA.

8. Refer to Wiring Specification for MXL, MXL-IQ and MXLV

Systems, P/N 315-092772 revision 6 or higher, for additional wiring

information.

AIC-4Z AIC-4Z

13 141516 9

910

10 11

11 12

E.O.L.R.

120 OHMS, 1/2 W,

P/N 140-099066

DO NOT USE

TO POWER SUPPLY, TB2 LOAD -

TO POWER SUPPLY, TB2 LOAD +

TO ACC, TB2, TERMINAL 9

TO ACC, TB2, TERMINAL 10

MULTI ZONESINGLE ZONE

CON4

CON4 CON3

CON3 CON2

CON2 CON1

CON1

TB1

LK1

LK2

LK3

TO ACC #31, P4

TO ACC #30, P4

TO ACC #29, P4

TO ACC #28, P4

TO ACC #1, P4

CABLE P/N IC-12

CABLE P/N 500-693801

JUMPER SETTINGS

LK1 1-2 JUMPERED

LK2 2-3 JUMPERED

LK3 2-3 JUMPERED

JUMPER SETTINGS

LK1 1-2 JUMPERED

LK2 2-3 JUMPERED

LK3 2-3 JUMPERED

MOM-4

NIM-1W

SUPERVISED

CABLE P/N 555-190967

TO MMB, SMB OR PSR-1

24V

141516

E.O.L.R.

120 OHMS, 1/2 W,

P/N 140-099066

E.O.L.R.

120 OHMS, 1/2 W,

P/N 140-099066

DO NOT USE

LK1

LK2

7 8 9 10111213141516

TB3

123456

P10

TB7

REFER TO THE ANALASER AIR SAMPING

SMOKE DETECTION MANUAL, P/N 315-092893,

FOR CONNECTION OF THE ACC, THE POWER

SUPPLY, AND THE ANALASER DETECTOR AND

AIR SAMPLING NETWORK.

LK3

Figure 7

Connecting the NIM-1W to the AnaLASER

GROUND FAULT DETECTED AT <70K OHMS FOR TERMINALS 1-4.

Table of contents

Other Siemens Control Unit manuals

Siemens

Siemens VBI60.15-5L User manual

Siemens

Siemens WFZ43 User manual

Siemens

Siemens ZIC-4A Service manual

Siemens

Siemens FS-TRI-M User manual

Siemens

Siemens SINAMICS G130 TM150 User manual

Siemens

Siemens ASIsafe 3RK1205-0B.00 User manual

Siemens

Siemens ST950 User manual

Siemens

Siemens SIMATIC ET 200SP CM 1xDALI User manual

Siemens

Siemens Simatic Net Scalance M812 User manual

Siemens

Siemens MM7000 Series User manual

Siemens

Siemens SINUMERIK 828D Turning Parts list manual

Siemens

Siemens LMU54 Series Operator's manual

Siemens

Siemens SINAMICS Startdrive User manual

Siemens

Siemens SINUMERIK 840D sl User manual

Siemens

Siemens WF 723 C Operating instructions

Siemens

Siemens 3RA2816-0EW20 User manual

Siemens

Siemens Simatic S7-1500 User manual

Siemens

Siemens SIMATIC ET 200SP User manual

Siemens

Siemens SIRIUS 3RT1916-4KA User manual

Siemens

Siemens SINAMICS Series Technical Document

Siemens

Siemens SINAMICS G130 User manual

Siemens

Siemens HZM User manual

Siemens

Siemens SINAMIC G130 User manual

Siemens

Siemens SIMADYN D MS51 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual