Siemens FS-TRI-M User manual

SiemensBuilding Technologies, Inc.

FlorhamPark, New Jersey 07932

RED BLK ORG ORG GRN

EARTH

GND

TOCONTROL PANEL

ORPREVIOUS ADDRESSABLE DEVICE

MODEL: FS-TRI-M

REFER TO INSTL. INSTR.

P/N 315-699487

DEVICE ADDR.__________

ALLTERMINALS ARE POWERLIMITED

NOTE:

DO NOT USE

REAR CONDUIT ENTRY

SINGLE GANG

SWITCHBOX

(USER SUPPLIED)

SINGLE GANG

SWITCHPLATE (BLANK)

(USER SUPPLIED)

FS-TRI-M

UNDERWRITERS

LABORATORIES

The SIEMENS FS-TRI-M Contact Monitoring Module,

as shown in Figure 1, interfaces normally open contact

devices to an ddressable Device Circuit of a fire

alarm control unit.

The FS-TRI-M supports Style B (Class B) Initiating

Device Circuit wiring. Each module uses one address

on the ddressable Device Circuit. It does not require

any mechanical address programming. Use the FS-FPI

Programmer/Tester to program and test the module.

PROGRAMMING INSTRUCTIONS

CAUTION:

1. To prevent damage to the FS-FPI, do not

connect module to the FS-FPI until the

Addre able Device Circuit wiring i

di connected.

2. Only one device mu t be connected to the

FS-FPI at a time.

1. Connect the red and black wires of the FS-TRI-M

to the SIEMENS FS-FPI Programmer/Tester. Use

the cable provided with the Programmer/Tester

and the 2 alligator clips provided.

2. Set the address for the module by following the

instructions in the FS-FPI Programmer/Tester

Manual (P/N 315-699480).

3. Record the device address on the label located

on the module. The module can now be installed

and wired to the system.

MOUNTING

The FS-TRI-M mu t be in talled in a

UL Li ted electrical box.

Refer to Figure 2.

1. Connect the appropriate wires using wire nuts.

Tuck the FS-TRI-M module inside the electrical

box and dress the wiring as required.

2. Fasten the cover plate (user supplied) to the box.

Figure 2

FS-TRI-M Mounting

P/N 315-699487-1

Siemens Building Technologies, Inc.

8 ernwood Road

lorham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 CN

Installation Instructions

Models FS-TRI-M

Contact Monitoring Module

Fire Safety

Figure 1

FS-TRI-M Module

Figure 3

FS-TRI-M Wiring

NOTES:

1. ll circuits are power limited.

2. In supervisory:

FS-TRI-M draws 1.5m

3. Initiating Device Circuit ratings:

Style B, Class B

See NFP 72 standard for the number of normally open contact devices allowed.

Voltage (max.): 5 VDC (during polling)

Supervisory current (max.): 0.5m (during polling)

larm current (max.): 0.8m (during polling)

IDC cable requirements:

Wire size: 18 to 14 WG

Wire resistance (max.): 2 ohms

Cable length (max.): 200 feet

Cable Type: Data grade, twisted pair

4. If Earth Ground is available, the green wire should be connected to earth ground.

5. If Earth Ground is NOT available, the IDC wiring should be limited to the same room.

RED

BLACK

GREEN

ORANGE

FS-TRI-M

-TO NEXT

ADDRESSABLE DEVICE

FROM ADDRESSABLE DEVICE

CIRCUIT OF A COMPATIBLE

CONTROL UNIT OR PREVIOUS

ADDRESSABLE DEVICE

GROUND

SEE NOTES 4 AND 5

END OF LINE RESISTOR

P/N 140-820185

3.6K, 1/4W, 5%

CONTACT DEVICE

INITIATING DEVICE CIRCUIT

SUPERVISED, SEE NOTE 3

ADDRESSABLE DEVICE CIRCUIT

24VDC NOMINAL, SUPERVISED

WIRING

Remove all y tem power before in tallation, fir t battery and then AC.

(To power up, connect AC first then battery.)

Refer to the wiring diagram and wire the module accordingly.

P/N 315-699487-1

Other Siemens Control Unit manuals

Siemens

Siemens SIRIUS User manual

Siemens

Siemens VAG60 Series User manual

Siemens

Siemens Desigo PXC4.E16 User manual

Siemens

Siemens MJ-X Series User manual

Siemens

Siemens MICROMASTER 420 User manual

Siemens

Siemens IP-Module User manual

Siemens

Siemens CPU 412-5H Technical Document

Siemens

Siemens SR-35 User manual

Siemens

Siemens Flowrite 599 Series Owner's manual

Siemens

Siemens SINAMICS G120P CU230P-2 Administrator guide

Siemens

Siemens XT55 GPS Startup User manual

Siemens

Siemens HCP User manual

Siemens

Siemens SINAMICS CONNECT 500 User manual

Siemens

Siemens SIMATIC S7-300 FM 350-1 User manual

Siemens

Siemens SIMATIC 8DO 24 V DC/0.5 A HF User manual

Siemens

Siemens K60R User manual

Siemens

Siemens SINAMICS S120 User manual

Siemens

Siemens SIRIUS ACT 3SU1400-1GE10-1AA0 User manual

Siemens

Siemens SIMATIC ET 200SP Technical Document

Siemens

Siemens AZL2 Series User manual

Siemens

Siemens 3VM9.88-0LB10 User manual

Siemens

Siemens XCI2001-U1 Guide

Siemens

Siemens SINUMERIK 828D PPU Series User manual

Siemens

Siemens Logo! CM EIB User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual