Siemens ZIC-4A Service manual

SiemensSiemens

Siemens IndustryIndustry

IndustryIndustry

Industry,,

,Inc.Inc.

Inc.Inc.

Inc.

BuildingBuilding

Building

Tecec

ecec

echnologies Dihnologies Di

hnologies Dihnologies Di

hnologies Divisionvision

visionvision

vision

P/N 315-033050-15

Zone Indicating Card

Installation Instructions

Model ZIC-4A

CONTENTS

INTRODUCTION ............................................................................................... 3

Features............................................................................................................ 3

OPERATION ..................................................................................................... 4

Controls and Indicators ..................................................................................... 4

PRE-INSTALLATION ......................................................................................... 5

Output Zones ................................................................................................... 6

ZIC-4A Switch and Jumper Settings ................................................................. 7

Programming Options ...................................................................................... 7

WIRING ............................................................................................................ 8

Using Multiple Power Supplies......................................................................... 9

INSTALLATION ............................................................................................... 10

ELECTRICAL RATINGS ................................................................................... 10

CONFIGURATIONS ........................................................................................ 11

Bell Follower ................................................................................................... 11

ZIC-4A Supervised Notification Appliance Wiring ........................................... 12

ZIC-4A Supervised Municipal Tie Wiring ......................................................... 13

ZIC-4A Leased Line Wiring ............................................................................. 13

ZIC-4A Releasing Service Wiring .................................................................... 14

ZIC-4A Releasing Service Wiring With PSC-12 Power Supply ......................... 15

ZIC-4A Bell Follower Circuit Wiring ................................................................. 16

ZIC-4A Two-Channel Audio Wiring................................................................... 17

ZIC-4A Single-Channel Audio Wiring ............................................................... 18

ZIC-4A Two-Channel Audio and Strobe Wiring ................................................ 19

ZIC-4A Single-Channel Audio and Strobe Wiring ............................................ 20

FireFinder-XLS/Desigo Fire Safety Modular/Cerberus PRO Modular

Releasing Logic .............................................................................................. 21

INTRODUCTION The Model ZIC-4A from Siemens Industry, Inc. is a zone

indicating card that provides notification appliance circuits

for the FireFinder-XLS/Desigo Fire Safety Modular/

Cerberus PRO Modular system. It has 4 outputs that can

be configured for Class A or Class B and control of audible

and visual notification appliances such as horns, speakers,

bells, strobes etc. Its outputs can also be configured as

connection to Municipal Tie, Releasing Service per NFPA

13 and 2001 or as a connection to a Leased Line remote

monitoring circuit.

Each zone can be configured independently for different

usages as programmed in the Zeus tool and can be

controlled automatically by program logic or manually

using the PMI/PMI-2/PMI-3 (XLS), FCM2041-U2 (Desigo

Fire Safety Modular), FCM2041-U3 (Cerberus PRO

Modular). During the initial power-up condition, each

zone on the ZIC-4A is configured as a steady NAC, Class

A configuration with 2A current limit. The ZIC-4A then

sends a message to the PMI/PMI-2/PMI-3 (XLS),

FCM2041-U2 (Desigo Fire Safety Modular), FCM2041-U3

(Cerberus PRO Modular) indicating that it is

unconfigured.

The ZIC-4A supports synchronized and non-synchronized

strobes.This selection is available in the Zeus tool under

the detail properties for each ZIC-4A circuit. Synchroniza-

tion across multiple ZIC-4A cards is automatic as a part of

the FireFinder-XLS/Desigo Fire Safety Modular/Cerberus

PRO Modular operating characteristics. Refer to docu-

ment P/N 315-096363 for a list of strobes that support

synchronization.

Features ZIC-4A features are as follows:

• Class A / Class B circuit configuration

• Zones can be configured independently

• Can have independent input source for each output

• Zone input voltage supervision

• Zone output supervision

• Intelligent self-restoring power limiting

• Coded signal synchronization capability

• Card level Ground Fault detection

• Communicate H-Net protocol

• Uploadable firmware update

• Ability to pass through up to 3A per circuit

GND FAULT

TRBL

ZONE 4 ACTIVE

TRBL

ZONE 2 ACTIVE

ZONE 1 ACTIVE

TRBL

ZONE 3 ACTIVE

CARD FAIL

HNET FAIL

CAN FAIL

RESET

POWER

ZIC-4A

HNET/CAN

HUNDREDS

TENS

ONES

Figure 1

ZIC-4A Zone Indicating Card

SiemensSiemens

Siemens IndustryIndustry

IndustryIndustry

Industry,,

,Inc.Inc.

Inc.Inc.

Inc.

BuildingBuilding

Building

Tecec

ecec

echnologies Dihnologies Di

hnologies Dihnologies Di

hnologies Divisionvision

visionvision

vision

P/N 315-033050-15

Installation Instructions

Model ZIC-4A

Zone Indicating Card

Siemens Industry, Inc.

Building Technologies Division

P/N 315-033050-154

OPERATION The ZIC-4A contains four Class A circuits. Each circuit is rated at 3A at 24VDC and

has an input connected to the power source and an output where the NAC devices,

Municipal Tie, Releasing service and Leased Line remote monitoring device are

connected. The zone inputs are isolated from one another and are supervised for the

presence of power. This allows the use of different power sources with different

ground references.The zone output is supervised for open and short circuit condi-

tions while the zone is inactive and allows different combinations of output configura-

tions (Standard NAC, Releasing, etc.) per card. Each ZIC-4A card occupies any one

card slot in the CC-5 cardcage.The ZIC-4A also has the capability to detect ground

fault on its zone output as indicated by a diagnostic LED.

Controls and Indicators The front panel of the ZIC-4A contains one reset switch, thirteen LEDs, and three

HNET address switches as shown in Figure 1.

A reset switch is located on the top of the front panel. Pushing the reset switch

re-initializes the ZIC-4A operation.

The LEDs follow the reset switch and their functions are defined as follows:

POWER (Green) Normally ON. When illuminated, indi-

cates that power for the ZIC-4A is

applied to the card.

CARD FAIL (Yellow) Normally OFF. When illuminated, indi-

cates that the card microprocessor has

failed.

CAN FAIL (Yellow) Normally OFF. When illuminated, indicates

that the CAN communication with the

ZIC-4A has terminated and the card goes

into degrade mode (applicable only when

card resides in a CAN network). NOT

USED for FireFinder-XLS/Desigo Fire

Safety Modular/Cerberus PRO Modu-

lar applications.

HNET FAIL (Yellow) Normally OFF. When illuminated, indi-

cates that the HNET communication with

the ZIC-4A has terminated and the card

goes into degrade mode (applicable only

when card resides in the HNET network).

GND FAULT (Yellow) Normally OFF. When illuminated, indi-

cates that the ZIC-4A has detected either

a negative or positive ground fault on its

field wiring.

ZONE 1 ACTIVE (Red) Normally OFF. When illuminated, indi-

cates that Zone 1 is active.

TROUBLE (Yellow) Normally OFF. When illuminated, indi-

cates that the ZIC-4A has detected a

trouble on Zone 1 (open circuit or short

circuit).

ZONE 2 ACTIVE (Red) Normally OFF. When illuminated, indi-

cates that Zone 2 is active.

Siemens Industry, Inc.

Building Technologies Division

P/N 315-033050-155

TROUBLE (Yellow) Normally OFF. When illuminated, indi-

cates that the ZIC-4A has detected a

trouble on Zone 2 (open circuit or short

circuit).

ZONE 3 ACTIVE (Red) Normally OFF. When illuminated, indi-

cates that Zone 3 is active.

TROUBLE (Yellow) Normally OFF. When illuminated, indi-

cates that the ZIC-4A has detected a

trouble on Zone 3 (open circuit or short

circuit).

ZONE 4 ACTIVE (Red) Normally OFF. When illuminated, indi-

cates that Zone 4 is active.

TROUBLE (Yellow) Normally OFF. When illuminated, indi-

cates that the ZIC-4A has detected a

trouble on Zone 4 (open circuit or short

circuit).

Three rotary dial switches at the bottom of the front panel are used to set the HNET

network address of the ZIC-4A.

PRE-INSTALLATION The following components must be set prior to inserting the card to the CC-5 (refer

to Figure 2):

S1 Primary Bell Follower Select Switch:

This switch selects Zone 1 as the Primary

Bell Follower.Toggle the S1 switch

towards the bottom of the board if Zone

1 is configured as a Primary Bell Follower;

otherwise toggle it to the top of the

board for normal operation (as shown in

Figure 2.)

S2, Leased Line Select Switches:These

switches select the zones configured for

Leased Line application.Toggle each

switch to the ON position if the corre-

sponding zone is configured as Leased

Line. If the zone is not configured as a

Leased Line application, the correspond-

ing zone switch must be set to the OFF

position.

During card failure, Zone 1 and Zone 2

outputs will activate if the FireFinder-

XLS/Desigo Fire Safety Modular/Cerberus

PRO Modular Alarm bus is asserted,

Zone 3 outputs will activate the if the

FireFinder-XLS/Desigo Fire Safety

Modular/Cerberus PRO Modular Trouble

Bus is asserted.You must configure each

zone to the proper Leased Line remote

monitoring circuit.

Silver line on S1 and jumpers P1 and

P4 indicates normal operation.

96 PIN DIN

PLUG CONNECTOR

RESET

SWITCH

LEASED LINE

SELECT

ZONE INPUT

SUPR ENABLE

NETWORK

ADDRESS

INPUT

POWER

SELECT

EXT

POWER

Figure 2

ZIC-4A Switch Location

Siemens Industry, Inc.

Building Technologies Division

P/N 315-033050-156

S2-SW1: Set to ON if Zone 1 usage = Leased Line, Alarm Default only

S2-SW2: Set to ON if Zone 2 usage = Leased Line, Alarm Default only

S2-SW3: Set to ON if Zone 3 usage = Leased Line,Trouble Default only

S2-SW4: Set to OFF: Not Used

S3, Reset Switch: Momentarily Closed switch that when pressed will initiate a hard

reset to the ZIC-4A (similar to a cold boot).

S4, S6, S7 Network Address Switch: Set the three-digit HNET network address for

the ZIC-4A using the three rotary dial address switches located near the bottom of

the front panel. (Refer to Figure 1 for the location of the switches.) The address for

the ZIC-4A must be the same as the address selected for it in the Zeus Programming

Tool. To set the address, turn the pointers on each of the three dials to the numbers

for the selected address. For example, if the address is 123, set the pointer for the

HUNDREDS dial to “1”, set the pointer for the TENS dial to “2”, and set the pointer for

the ONES dial to “3”. The range of allowable addresses is from 001 to 251 (leading

zeros must be used).

S5 Input Power Select: This switch selects the source of voltage input to power the

ZIC-4A. BP Power indicates that the input is derived from the backplane of the CC-2/

CC-5 and EXT Power indicates that the input is derived from E5/E11 terminal of the

CC-2/CC-5, normally connected to non-power limited output of the PSC-12/PSX-12. It

is important to take into account the source of the voltage during battery calculations.

P1, P2, P3, P4 Shunt Headers, NAC Input Supervision Enable:These headers

select the NAC input zone supervision. If usage application is set for speaker func-

tion, place the shunt jumpers of the corresponding zone between 1—2 and between

5—6, otherwise place the shunt jumpers between 1—3 and 4—6.

P1 selects NAC input supervision for Zone 1

P2 selects NAC input supervision for Zone 2

P3 selects NAC input supervision for Zone 3

P4 selects NAC input supervision for Zone 4

Output Zones The ZIC-4A can be configured for the following usages:

Standard NAC Zone - Configurable as the following NAC zones:

Steady Strobe (Synchronized or Unsynchronized)

Zone Coding Temporal Code

Temporal 4, when used with Audible Base SBGA-34

March Time 120 March Time 60

March Time 30 Horn / Strobe

Releasing Zone - For release of FM-200, Halon, Pre-action & Deluge Sprinklers for

Canada or USA. Releasing zone requires an REL-EOL module for proper wire supervision.

Municipal Tie - Configurable as a supervised connection to municipal tie. Municipal

Tie usage application requires the LLM-1 interface module.

Leased Line - Configurable as a connection to a remote monitoring system. Leased

Line usage application requires LLM-1 interface module.

Bell Follower Primary - Configurable as a Bell Follower Primary (Zone 1 only).

Bell Follower Secondary - Configurable as a Bell Follower Secondary.

HNET

Siemens Industry, Inc.

Building Technologies Division

P/N 315-033050-157

SGNITTESREPMUJDNAHCTIWSA4-CIZ

EGASUENOZ1S2SNOITISOPREDAEH

CANlamroNFFO6-4,3-1

eiTlapicinuMlamroNFFO6-4,3-1

enoZgnisaeleRlamroNFFO6-4,3-1

eniLdesaeLl

amroNNO-)enoZ(WS6-4,3-1

yramirP-rewolloFlleB )ylnO1enoZ( lamroNffOFFO6-4,3-1

yradnoceS-rewolloFlleBlamroNFFO6-4,

3-1

gnidoCenoZlamroNFFO6-4,3-1

slleBdedoClamroNFFO6-4,3-1

enoZrekaepSlamroNFFO6-5,2-1

Programming Options In order to perform its intended operation, the ZIC-4A card must be programmed

using the Zeus Programming Tool. The ZIC-4A card and its Out Ckt properties must

be set prior to normal operation.

In the Zeus Programming Tool, highlight the selected ZIC-4A card in the Physical

View and open the Detail View - Properties to modify and/or define the following

ZIC-4A card properties:

HNET Address This address must match the address

set in the ZIC-4A hardware.

Slot Location This defines the location where the

ZIC-4A is inserted in the CC-5.

Base Language Custom Message The message associated with the ZIC-4A

card.

Alternate Language Custom Message The message associated with the ZIC-4A

card in an alternate language.

ZIC Card 24V Power Source Select back plane or screw terminals.

Each ZIC-4A card is subdivided into four output circuits that can be programmed

independently of each other. In the Zeus Programming Tool, highlight the selected

ZIC-4A Output Ckt in the Physical View and open the Detail View - Properties to

modify and/or define the following ZIC-4A output circuit properties:

Device Address Shows preset address of ZIC card output.

Base Language Custom Message The message associated with the ZIC-4A

output circuit.

Alternate Language Custom Message The message associated with the ZIC-4A

output circuit in an alternate language.

Device Usage Signal

ZIC Circuit Usage Select usage required (see list).

ydaetSCANmrlAeniLdesaeL

dedoCCANyramirPloflleB

cnySebortSnroHyradnoceSloflleB

)ebortSnroH(ylnOnroH.liSrekaep

SV52

cnySebortSrekaepSV07

cnySnUebortSrekaepSV001

eiTlapicinuMenoZgnisaeleR

Degrade Mode Alarm Activation Determines if Degrade Alarm will activate

the ZIC-4A circuit when asserted.

Siemens Industry, Inc.

Building Technologies Division

P/N 315-033050-158

Figure 3

Wiring The 24VDC Power Lines To The

ZIC-4A Slot In The CC-5

12345678

910111213141516

CLASS A

OUTPUTS SHOWN IN ACTIVE STATE

CLASS A

17 18 19 20 21 22 23 24

ZONE 1

ZONE 3

ZONE 1

INPUT

ZONE 2

ZONE 4

ZONE 2

INPUT

ZONE 3

INPUT

ZONE 4

INPUT

ONE SLOT OF CC-5

Silenceable Determines if the circuit is Silenceable or

Non-Silenceable.

Wiring Type Defines if the circuit is Class A or Class B

wiring type.

Total Current Drawn Select actual current load of output

circuit (see list).

pmA0.0pmA5.1pmA0.3

pmA5.0pmA0.2pmA5.3

pmA0.1pmA5.2pmA0.4

If the zone usage is set in the Zeus Programming tool as “Sil Horn Only (Horn Strobe)”,

the Silenceable Option is always set and is specific to the Horn of the Horn Strobe

device and the strobe is always Non-Silenceable.

Some restrictions apply to certain usage selections (for example, Municipal Tie can

only be configured as Class B wiring type) that are enforced by the Zeus tool during

Edit mode or Compile time.

Refer to the Zeus Quick Start Manual, P/N 315-033875, or the Zeus self-help index

for more information.

WIRING

Remove all system power before installation, first battery then AC. (To power up,

connect the AC first, then the battery.)

All field wiring to the ZIC-4A is connected to

the terminal blocks of the CC-5 card cage

slot in which it is installed (Refer to Figure 3).

To Connect External Wiring

1. Loosen the screw of the terminal

by turning it counterclockwise.

2. Insert the wire into the side of the

terminal block.

3. Tighten the screw of the terminal

block by turning it clockwise.

The top terminals (1 through 8 and 9

through 16) are connected to the notifica-

tion appliance devices such as bells, horns,

strobes, speakers, etc. Each zone has four

terminal connections: (+), Class A (+), (-),

Class A (-). These terminals are power

limited.

The bottom terminals (17 through 24) are

connected to the input power source of the

NAC devices. Each zone has a (+) terminal

and (-) terminal. These terminals are not

power limited.

Siemens Industry, Inc.

Building Technologies Division

P/N 315-033050-159

Care must be taken when installing the zone input and zone output field wiring to

prevent possible cross wiring.This can cause severe damage to the system

when powered up or when zone is activated.

The screw terminals can accommodate one 12-18 AWG or two 16-18 AWG.

If the total output of all 4 zones exceeds 12 amps, a single PSC-12 cannot be used to

supply the ZIC-4A. Refer to the PSC-12 Installation Instructions, P/N 315-033060 for

information when the total system load exceeds 12 amps.

17 18 19 20 21 22 23 24

TO PSC-12, TB4 +

TO PSX-12, TB4 +

TO PSC-12, TB4 -

TO PSX-12, TB4 -

ONE SLOT OF CC-5

USING A SINGLE

PSC-12 TO

POWER A ZIC-4A

USING A PSC-12 TO

POWER INPUTS 1-3

AND A PSX-12 TO

POWER INPUT 4

USING A PSC-12 TO

POWER INPUTS 1-2

AND A PSX-12 TO

POWER INPUTS 3- 4

Figure 4

Using Multiple Power Supplies

Siemens Industry, Inc.

Building Technologies Division

P/N 315-033050-1510

Figure 5

Installing The ZIC-4A

INSTALLATION The ZIC-4A plugs perpendicularly into one slot in the CC-5 card-cage via two 96-pin

DIN connectors and can occupy any slot in the card cage. (Refer to Figure 5.)

Insert the ZIC-4A card into the card guides right side up (lettering on the front panel

is legible).

Slide the card in until the card edge connectors contact the recep-

tacles on the motherboard.

Verify that the DIN connectors of the card and the card-cage aligned

properly. The card can only plug in one direction to the card cage, if it

does not align, DO NOT FORCE the card.

Place thumbs on the front panel adjacent to the captive screws and

gently apply even pressure on the card until the connectors seat in the

receptacles on the motherboard. Secure with the captive screws.

If the ZIC-4A is being powered from an external source, verify that E5 has the proper

voltage and proper terminal connections.

ELECTRICAL RATINGS

roenalPkcaBV42 tnerruCrewoPlanretxE wolebETONeeS

tnerruCV42lanimreTwercStnerruCeciveDlatoT

tnerruCenalPkca

BV2.60

tnerruCybdnatSV42Am98

:ETON .A4-CIZehtfotkCCIZhcaefoepytgniriwdnaegasuehtnotnednepedsitnerrucV42ehT .epytgniriwdnaegasuenozhcaerofswardtnerrucderiuqerehterawolebdetsiL

tnemeriuqeRtnerruCA4-CIZ

egasUenoZ tnerruCtuptuO tnemeriuqeR tnerruCAssalC tnemeriuqeR

desUtoN00

CANAm71Am6

.cnyS-ebortSAm71Am6

.cnysnU-ebor

tSAm71Am6

ASU-eiTlapicinuMAm430

adanaC-eiTlapicinuMAm710

enoZgnisaeleRAm710

mralA-eniLdesaeLAm710

elbuorT-eniLdesaeLA

m710

vpuS-eniLdesaeLAm710

yramirP-rewolloFlleB00

yradnoceS-rewolloFlleBAm71Am6

enoZrekaepSAm43Am6

dedoC-CANAm71Am6

Am9

8=tnerruCybdnatSA4-CIZ

Table of contents

Other Siemens Control Unit manuals

Siemens

Siemens 3RK1408-8K.00-0AA2 User manual

Siemens

Siemens SIMOTION D4 5-2 Series User manual

Siemens

Siemens XDLC User manual

Siemens

Siemens SINAMICS S120 Technical Document

Siemens

Siemens SIMATIC ET 200S User manual

Siemens

Siemens SINUMERIK 828D Turning User manual

Siemens

Siemens SIRIUS 3RT2 User manual

Siemens

Siemens LFE1 Series User manual

Siemens

Siemens SIRIUS 3SB3 User manual

Siemens

Siemens HLIM User manual

Siemens

Siemens SI120 Instruction sheet

Siemens

Siemens SINAMICS G120 User manual

Siemens

Siemens SINAMICS G120 User manual

Siemens

Siemens RVD240 Operator's manual

Siemens

Siemens CU240S DP-F User manual

Siemens

Siemens SIPROTEC 7SJ61 Instruction manual

Siemens

Siemens SINUMERIK 840D Parts list manual

Siemens

Siemens SINUMERIK 802D sl Owner's manual

Siemens

Siemens SINAMICS S120 User manual

Siemens

Siemens 8GK9735-1KK.0 User manual

Siemens

Siemens RC-30U User manual

Siemens

Siemens LGI16 Series User manual

Siemens

Siemens SIMOCODE pro 3UF7902-0AA00-0 User manual

Siemens

Siemens SINAMICS CONNECT 500 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual