Siemens HZM User manual

SiemensSiemens

Siemens IndustryIndustry

IndustryIndustry

Industry,,

,Inc.Inc.

Inc.Inc.

Inc.

BuildingBuilding

Building

Tecec

ecec

echnologies Dihnologies Di

hnologies Dihnologies Di

hnologies Divisionvision

visionvision

vision

P/N 315-034850-8

INTRODUCTION The Model HZM from Siemens Industry, Inc. is an intelligent device that connects a

single zone of conventional devices to a DLC (FireFinder-XLS System) or FS-DLC (FS-

250 System) device loop.The HZM can power up to fifteen compatible 2-wire, ioniza-

tion or photoelectric smoke detectors or it can power one PB-1191 Beam Detector. It

can also monitor an unlimited number of shorting devices such as waterflow switches,

thermal detectors, manual stations, etc.

Each HZM can be assigned a custom message using either the Zeus Programming

Tool (FireFinder-XLS System) or the FS-CT2 (FS-250 System). Refer to the Zeus Quick

Start Manual, P/N 315-033875, or the FS-250 Programming Manual, P/N 315-049403,

as applicable.The alarm verification configuration is used only for non-shorting detectors.

The HZM supports Class A and Class B wiring.The module uses one address on the

device loop. It does not require any mechanical address programming. Use the DPU

Device Programming Unit to program and test the module.

HZM HZM

FRONT BACK SIDE

ALARM

1 2 3 4 56 7 8 9

PROGRAMMING

POINTS

Figure 1

HZM Module

The HZM is not listed for use in mass notification applications.

Controls And Indicators The HZM has a multicolor LED, visable through the cover plate, which indicates the

condition of the circuit.This multicolor LED displays red for alarm, yellow for trouble,

and green for normal operation (See Figure 1).

PRE-INSTALLATION Setting The Module Address

1. Using the DPU Device Programming Unit, plug the programming cable into

the programming points on the HZM (See Figure 1).

2. Set the address for the HZM by following the instructions in the DPU

Manual, P/N 315-033260.

Remote Conventional Zone Module

Installation Instructions

Model HZM

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034850-82

INSTALLATION

Remove all system power before installation, first battery then AC. (To power up,

connect the AC first, then the battery.)

Electrical Connections After you have set the HZM address, connect the field wiring.

There are three basic

connections

to the HZM: initiating devices, DLC or FS-DLC device loop, and 24 VDC

power. All terminals are power limited.

Initiating Devices (Figures 2, 3, and 4)

The HZM supports one zone of initiating devices in either Class A or Class B.The

initiating devices are connected to terminals 5–8 on the HZM terminal block. The

HZM is a polarity insensitive module and terminals 1 and 2 can be connected to

either line of the DLC or FS-DLC Device Loop. Figure 2 shows the Class A wiring.

Figure 3 shows the Class B wiring.

123456789

EARTH

DEVICE LOOP

24VDC POWER

LINE 2

LINE 1

TYLE D

(DCLA)

EOL * †

* EOL DEVICE IS 4.7K, 1/4W (P/N 140-820188)

FOR CANADIAN APPLICATIONS, USE MODEL†

EL-33 WITH 4.7K, 1/4W RESISTOR.

+++

Figure 2

HZM Initiating Devices Wiring Diagram

Class A/Style D (ULC DCLA) Installation

Figure 3

HZM Initiating Devices Wiring Diagram

Class B/Style B (ULC DCLB) Installation

DEVICE LOOP

4VDC POWER

LINE 2

LINE 1

6789

EARTH

NOT USED

TYLE B

(DCLB)

* EOL DEVICE IS 4.7K,

1/4W (P/N 140-820188)

FOR CANADIAN APPLICATIONS,†

USE MODEL EL-33 WITH

4.7K, 1/4W RESISTOR.

EOL*

†

NOTES

1. Wire 18 AWG minimum, 12

AWG maximum, 35 ohms Max.

2. Supervised, power limited to

NFPA 70 per NEC 760.

3. Voltage 24VDC.

4. Positive and negative ground

fault detected at <60K ohms

for terminals 5-8.

NOTES

1. Wire 18 AWG minimum, 12

AWG maximum, 35 ohms Max.

(both sides)

2. Supervised, power limited to

NFPA 70 per NEC 760.

3. Voltage 24VDC.

4. Positive and negative ground

fault detected at <60K ohms

for terminals 5, 8.

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034850-83

Figure 4 shows the wiring for the PB-1191 beam detector. When the PB-1191 is used,

the 2-position plug from jumper J1 must be removed.

Follow the steps listed below to remove the 2-position plug from J1:

a. Remove the screw from the center of the HZM plastic cover and place it to

one side.

b. Remove the circuit board and locate jumper J1.

c. Remove the 2-position plug from J1.

d. Reassemble the circuit board and plastic cover using the screw that was

removed in the first step.

e. Be sure to use the correct end of line device with the HZM in this configuration.

PB-1191

A B C D EF

1 2 3 4 56789

BEAM DETECTOR WIRING

CLASS B/STYLE B

(ULC DCLB)

HZM

EARTH

3.6K, 1/4W

EOL RESISTO

P/N 140-820185

O NOT CONNECT MORE THAN

ONE PB-1191 TO AN HZM

DLC DEVICE LOOP

24VDC POWER

LINE 2

LINE 1

NOT USED

Figure 4

HZM Wiring Diagram For PB-1191 Installation

NOTE:

Positive and negative ground fault detected at <60K ohms for terminals 5, 8.

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034850-84

Device Loops (Figures 5 and 6)

The HZM communicates with the FireFinder-XLS via its DLC device loop. The device

loop may be wired Class A or Class B. Figure 5 shows both wiring types. Refer to the

DLC Installation Instructions, P/N 315-033090 for additional wiring information.

Do not mix wiring types; Zone 1 and Zone 2 must be the same wiring type.

NOTES

1. Loop resistance 50 ohms

Max with 252 devices on

the loop. Refer to the DLC

Installation Instructions, P/N

315-033090 if the number of

devices is less than 252.

2. Wire 18 AWG minimum, 12

AWG maximum.

3. No EOL device required.

4. Supervised, power limited to

NFPA 70 per NEC 760.

5. Positive and negative ground

fault detected at <60K ohms

for terminals 5-8 on HZM.

NOTES

1. Loop resistance 50 ohms

Max with 252 devices on

the loop. Refer to the DLC

Installation Instructions, P/N

315-033090 if the number of

devices is less than 252.

2. Wire 18 AWG minimum, 12

AWG maximum.

3. No EOL device required.

4. No jumper required between

terminal 1 and 2, terminal 3

and 4.

5. Supervised, power limited to

NFPA 70 per NEC 760.

6. Positive and negative ground

fault detected at <60K ohms

for terminals 5-8 on HZM.

TALLATI

NO T-TAPPING ALLOWED

CLASS B** INSTALLATION

T-TAPPING ALLOWED

*OPERATES IN FULLCONFORMANCE WITHSTYLE 6(ULC DCLA)

**OPERATES IN FULL CONFORMANCE WITH STYLE 4 (ULC DCLB)

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

CC-5/CC-2

ZON

ZONE

ZON

ZONE

NOT

USED

11 1

22 2

33 3

44 4

55 5

66 6

77 7

88 8

99 9

HZM HZM HZM

HZM

LINE 2

LINE 1

11 1

22 2

33 3

44 4

55 5

66 6

77 7

88 8

99 9

HZM HZM HZM

HZM

LINE 2

LINE 1

NOT USED

11 1

22 233 344 455 566 677 788 899 9

HZM HZM HZM

LINE 2 (RETURN)

LINE 2 (OUT)

LINE 1 (OUT)

LINE 1 (RETURN)

11 1

22 233 344 455 566 677 788 899 9

HZM HZM HZM

LINE 2 (RETURN)

LINE 2 (OUT)

LINE 1 (OUT)

LINE 1 (RETURN)

NOT

USED

CLASS A* INSTALLATION

NO T-TAPPING ALLOWED

CLASS B** INSTALLATION

T-TAPPING ALLOWED

*OPERATES IN FULL CONFORMANCE WITH STYLE 6 (ULC DCLA)

**OPERATES IN FULL CONFORMANCE WITH STYLE 4

(

ULC DCLB

)

ZONE

11 1

22 2

33 3

44 4

55 5

66 6

77 7

88 8

99 9

HZM HZM HZM

HZM

LINE 2

LINE 1

NOT USED

11 1

22 233 344 455 566 677 788 899 9

HZM HZM HZM

LINE 2 (RETURN)

LINE 2 (OUT)

LINE 1 (OUT)

LINE 1 (RETURN)

Loop Circuit

FS-DLC Device

NOT USED

Loop Circuit

FS-DLC Device

NOTES

1. Loop resistance 50 ohms

Max with 252 devices on

the loop. Refer to the FS-

250 Installation, Operation

and Maintenance Manual if

the number of devices is

less than 252.

2. Wire 18 AWG minimum, 12

AWG maximum.

3. No EOL device required.

4. When wiring Class B, no

jumper required between

terminal +OUT and +IN,

terminal -OUT and -IN.

5. Supervised, power limited to

NFPA 70 per NEC 760.

6. Positive and negative ground

fault detected at <60K ohms

for terminals 5-8 on HZM.

Figure 5

HZM Device Loop Wiring Diagram For FireFinder-XLS

The HZM communicates with the FS-250 via its FS-DLC device loop.The device loop

may be wired Class A or Class B. Figure 6 shows both wiring types. Refer to the

FS-250 Installation, Operation and Maintenance Manual, P/N 315-049353, for addi-

tional wiring information.

Figure 6

HZM Device Loop Wiring Diagram For FS-250

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034850-85

1ELBAT YTILIBITAPMOCMZH

snemeiS rotceteD ledoMesaB noitallatsnI snoitcurtsnI

H3/3-IDS3-BD91-349180-513

H3A/3A-IDS

3-BD91-349180-513

H3B/3B-IDI3-DA7-432390-513

11-TD11-BD TPDA-BDhtiwS3-BD 5-924590-513 5-924590-513

121IHE11-BD,1

1-BDa_56318201V6A

121HOE11-BD,11-BDa_76318201V6A

121POE11-BD,11-BDa_76318201V6A

1911-ABP1911-BBP3-424590-513

T11

/11-EP11-BD TPDA-BDhtiwS3-BD P11-DA

01-891490-513 01-891490-513 11-956590-513

24 VDC Power (Figure 7)

In a FireFinder-XLS System, the HZM receives its power from the 24 VDC power

output on TB3 of the PSC-12 or PSX-12. In an FS-250 System, the HZM receives its

power from the 24V power output on the control panel or auxiliary power supply. The

24 VDC power may be wired only as Class B. Since the HZM monitors the power at

its screw terminals, you can star or T-tap the power connection. Refer to Figure 7 for

the wiring diagram.

111

22 2

33 3

44 4

55 5

66 6

77 7

888

999

HZM HZM HZM

HZMHZM

CLASS B INSTALLATION

T-TAPPING ALLOWED

TO 24 VDC

SEE NOTE 5

Figure 7

HZM 24 VDC Wiring Diagram

Mounting

1. Mount the HZM in a standard two gang electrical box. The box must have a

depth of at least 3½ inches.

2. When the field wiring for the initiating devices, device loop, and 24 VDC is

connected, press the HZM into the box and fasten it with the four screws

provided.

3. Attach a dress bezel if necessary, making sure that the ALARM LED is

aligned with the hole in the bezel.

COMPATIBILITY The devices in Table 1 are listed for use with the HZM.

• Use up to fifteen detectors, any combination of those listed.

• Only one PB-1191 (consisting of a PBA-1191 detector and PBB-1191

base), and no additional devices, can be connected to an HZM.

• Detector operated accessories cannot be used with the HZM.

• The model numbers listed are the UL compatibility identifiers.

NOTES

1. Wire 18 AWG minimum, 12

AWG maximum.

3. No EOL device required.

4. Supervised, power limited to

NFPA 70 per NEC 760.

5. A power supply which is

resettable, power limited

and UL listed for fire

protective signaling use and

is rated between 18.8-28.2

VDC.

6. Positive and negative ground

fault detected at <60K ohms

for terminals 5-8 on HZM.

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034850-86

:enoZeciveDgnitaitinI

ecnatsiseRenoZ.xaMlatotsmho53

egnaRegatloVyrosivrepuSevawllufderetlifCDV5.42-81

tner

ruCenoZ.xaMAm43

rewoPCDV42

egnaRegatloVCDV2.82-8.81

tnerruC.xaMAm001

tnerruCybdnatSAm66

pooLCLD-SF/CLD

tnerruC.

xaMAm1

ELECTRICAL RATINGS

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034850-87

Cyber security disclaimer

Siemens products and solutions provide security functions to ensure the secure operation of

building comfort, fire safety, security management and physical security systems. The security

functions on these products and solutions are important components of a comprehensive security

concept.

It is, however, necessary to implement and maintain a comprehensive, state-of-the-art security

concept that is customized to individual security needs. Such a security concept may result in

additional site-specific preventive action to ensure that the building comfort, fire safety, security

management or physical security system for your site are operated in a secure manner. These

measures may include, but are not limited to, separating networks, physically protecting system

components, user awareness programs, defense in depth, etc.

For additional information on building technology security and our offerings, contact your Siemens

sales or project department. We strongly recommend customers to follow our security advisories,

which provide information on the latest security threats, patches and other mitigation measures.

http://www.siemens.com/cert/en/cert-security-advisories.htm

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Canada, Ltd.

1577 North Service Road East

Oakville, Ontario

L6H 0H6 Canada

P/N 315-034850-8

This page has been left intentionally blank.

Document ID A6V10233195

Table of contents

Other Siemens Control Unit manuals

Siemens

Siemens SIMATIC Panel PC 677 User manual

Siemens

Siemens SIMATIC ET 200S User manual

Siemens

Siemens ZIC-4AC User manual

Siemens

Siemens SIMATIC ET 200SP User manual

Siemens

Siemens PN16 User manual

Siemens

Siemens SINUMERIK 828D Turning User manual

Siemens

Siemens IM 155-6 PN ST User manual

Siemens

Siemens LYC11 User manual

Siemens

Siemens SINUMERIK 840DE SL Quick start guide

Siemens

Siemens SIMOTION Parts list manual

Siemens

Siemens SIMATIC TDC User guide

Siemens

Siemens SIMATIC S5 User manual

Siemens

Siemens SINAMICS G120D User manual

Siemens

Siemens SIMOTION D4 5-2 Series User manual

Siemens

Siemens DESIGO PXM20 User manual

Siemens

Siemens WF 725 Technical manual

Siemens

Siemens SIRIUS ACT 3SU1400-2EM10-6AA0 User manual

Siemens

Siemens VSA-1 User manual

Siemens

Siemens MXG461B Series Owner's manual

Siemens

Siemens SIMADYN D MS51 User manual

Siemens

Siemens SINAMICS G120 User manual

Siemens

Siemens SIMATIC S5 1P 243 Technical Document

Siemens

Siemens 3VL9800-3MJ00 User manual

Siemens

Siemens FM 458-1 DP User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual