Prorack K447 User manual
K447
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 6 x 6
x 6 x 4 x 2 x 6
Revision No: 7G 1
Fitting Kit K447
x 2 x 1 x 1 x 1
x 2
2
Fitting Kit K447
MAX kgs (lbs)
W/P WHD
Volkswagen
Caddy Maxi (3 Bar), 5dr Van 08-14 ZA 35 kgs (77 lbs) 50 kgs (110 lbs)
Caddy Maxi (3 Bar), 5dr Van 08-Nov 15 AU 35 kgs (77 lbs) 50 kgs (110 lbs)
Caddy Maxi (3 Bar), 5dr Van 08-Nov 15 NZ 35 kgs (77 lbs) 50 kgs (110 lbs)
3
Fitting Kit K447
X
A B C 1 2 3
Caddy Maxi (3 Bar), 5dr Van 08-14 (ZA) 100mm 860mm - 818mm 790mm 782mm
3 15/16ths" 33 7/8ths" - 32 3/16ths" 31 1/8ths" 30 13/16ths"
Caddy Maxi (3 Bar), 5dr Van 08-Nov 15 (AU) 100mm 860mm - 818mm 790mm 782mm
3 15/16ths" 33 7/8ths" - 32 3/16ths" 31 1/8ths" 30 13/16ths"
Caddy Maxi (3 Bar), 5dr Van 08-Nov 15 (NZ) 100mm 860mm - 818mm 790mm 782mm
3 15/16ths" 33 7/8ths" - 32 3/16ths" 31 1/8ths" 30 13/16ths"
4
Fitting Kit EN
K447
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
5
Fitting Kit EN
K447
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
●Please check the front of this manual for
information relating specifically to your
vehicle.
6
Fitting Kit EN
K447
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
7
Fitting Kit EN
K447
●Refer to the underside of the pad for the
part number.
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 11-04-216 Pads with bars
B = 11-04-219
C = 11-04-226
D = 11-04-227
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
8
Fitting Kit EN
K447
Fitment
●Remove fixed-point cover screws with 5mm
Hex Key.
●Use the following grubscrew lengths for
each position:
A = M8 x 55mm (2 1/8")
B = M8 x 70mm (2 3/4")
●Select grubscrews and screw into the
vehicle's fixed points.
●For additional weather protection, apply
silicon sealant in and around fixed point
hole and grubscrew (sealant not supplied).
●Place M8 washer over grubscrew.
●Fit nut to grubscrew.
●Height
Front: 60mm
Middle: 35mm
Rear: 40mm
9
Fitting Kit EN
K447
●Place crossbar foot over clamp.
●Tighten the plastic knob.
●In the fully tightened position, the knobs
should be parallel with the vehicle.
●Repeat for all four positions.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack PR3213 User manual
Prorack
Prorack PR3205 User manual
Prorack
Prorack PR3077 User manual
Prorack
Prorack K992 User manual
Prorack
Prorack K586 User manual
Prorack
Prorack K312 User manual
Prorack
Prorack K426 User manual
Prorack
Prorack K988 User manual
Prorack
Prorack Fitting Kit K440 User manual
Prorack
Prorack K411 User manual
Prorack
Prorack K381 User manual
Prorack
Prorack K156 User manual
Prorack
Prorack K053 User manual
Prorack
Prorack K603 User manual
Prorack
Prorack K105 Operation and installation manual
Prorack
Prorack PR3090 User manual
Prorack
Prorack K998 User manual
Prorack
Prorack K122 User manual
Prorack
Prorack K327 User manual
Prorack
Prorack K120 User manual
