Prorack K312 User manual
K312
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 2 x 4 x 4
Revision No: 6F 1
Fitting Kit K312
MAX kgs (lbs)
W/P WHD
Mazda
2, 5dr Hatch 02-06 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
2, 5dr Hatch 02-06 CN 50 kgs (110 lbs) 50 kgs (110 lbs)
2, 5dr Hatch Dec 02-Aug 07 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
2, 5dr Hatch Dec 02-Aug 07 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Demio, 5dr Hatch Dec 02-Aug 07 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
2
Fitting Kit K312
X
A B C 1 2 3
2, 5dr Hatch 02-06 (EU) -180mm 450mm - 795mm 785mm -
-7 -1/16ths" 17 3/4ths" - 31 5/16ths" 30 15/16ths" -
2, 5dr Hatch 02-06 (CN) -180mm 450mm - 795mm 785mm -
-7 -1/16ths" 17 3/4ths" - 31 5/16ths" 30 15/16ths" -
2, 5dr Hatch Dec 02-Aug 07 (AU) -180mm 450mm - 795mm 785mm -
-7 -1/16ths" 17 3/4ths" - 31 5/16ths" 30 15/16ths" -
2, 5dr Hatch Dec 02-Aug 07 (NZ) -180mm 450mm - 795mm 785mm -
-7 -1/16ths" 17 3/4ths" - 31 5/16ths" 30 15/16ths" -
Demio, 5dr Hatch Dec 02-Aug 07 (NZ) -180mm 450mm - 795mm 785mm -
-7 -1/16ths" 17 3/4ths" - 31 5/16ths" 30 15/16ths" -
3
Fitting Kit EN
K312
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4
Fitting Kit EN
K312
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5
Fitting Kit EN
K312
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 461A
B = 462A
6
Fitting Kit EN
K312
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Fit rubber pads (supplied with fitting kit) to
foot.
7
Fitting Kit EN
K312
●Make sure the pad fits into the holes
underneath the foot.
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
8
Fitting Kit EN
K312
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
9
Fitting Kit EN
K312
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
This manual suits for next models
1
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K998 User manual
Prorack
Prorack K949 User manual
Prorack
Prorack K361 User manual
Prorack
Prorack K708 User manual
Prorack
Prorack K122 User manual
Prorack
Prorack TP1 User manual
Prorack
Prorack EXP360U User manual
Prorack
Prorack K1222 User manual
Prorack
Prorack K049 User manual
Prorack
Prorack K062 User manual
Prorack
Prorack K145 User manual
Prorack
Prorack K310 User manual
Prorack
Prorack K527 User manual
Prorack
Prorack PR3600 User manual
Prorack
Prorack K376 User manual
Prorack
Prorack K410 User manual
Prorack
Prorack K027 Operation and installation manual
Prorack
Prorack K512 User manual
Prorack
Prorack K855 User manual
Prorack
Prorack K442 User manual
