Prorack K411 User manual
K411
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 2 x 2 x 1
x 1 x 2 x 2
Revision No: 2C 1
Fitting Kit K411
MAX kgs (lbs)
W/P WHD
Kia
Cerato , 4dr Sedan 09-+ AU 45 kgs (99 lbs) 45 kgs (99 lbs)
Cerato , 4dr Sedan 09-+ NZ 45 kgs (99 lbs) 45 kgs (99 lbs)
Forte , 4dr Sedan 10-+ US 45 kgs (99 lbs) 45 kgs (99 lbs)
2
Fitting Kit EN
K411
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3
Fitting Kit EN
K411
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment.
●Ensure each end of the crossbar is
adjusted equally.
4
Fitting Kit EN
K411
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Clamp Part Number:
A = 524A
B = 539A
5
Fitting Kit EN
K411
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
6
Fitting Kit EN
K411
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 11-04-255
B = 11-04-254
C = 11-04-243
●Fit rubber pad (supplied with crossbar) to
foot.
●Make sure the pad fits into the holes
underneath the foot.
7
Fitting Kit EN
K411
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Clamps directly to edge of roof under the
doors
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 5 Nm (3.7 ft lb).
8
Fitting Kit EN
K411
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
9
Fitting Kit EN
K411
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K091 User manual
Prorack
Prorack K363 User manual
Prorack
Prorack PR3715 User manual
Prorack
Prorack K127 User manual
Prorack
Prorack K474 User manual
Prorack
Prorack K182 Operation and installation manual
Prorack
Prorack K112 User manual
Prorack
Prorack S16 User manual
Prorack
Prorack K584 User manual
Prorack
Prorack K375 User manual
Prorack
Prorack K838 User manual
Prorack
Prorack K1245 User manual
Prorack
Prorack K938 User manual
Prorack
Prorack K631 User manual
Prorack
Prorack K377 User manual
Prorack
Prorack K751 User manual
Prorack
Prorack K1228 User manual
Prorack
Prorack K927 User manual
Prorack
Prorack K537 User manual
Prorack
Prorack K671 User manual
