Prorack K992 User manual
K992
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 1 x 1
x 4 x 2 x 2
Revision No: 1A 1
Fitting Kit K992
MAX kgs (lbs)
W/P WHD
SsangYong
Actyon, 5dr SUV 05-13 AU 60 kgs (132 lbs) 60 kgs (132 lbs)
Actyon, 5dr SUV 05-13 ZA 60 kgs (132 lbs) 60 kgs (132 lbs)
Actyon, 5dr SUV 05-13 EU 60 kgs (132 lbs) 60 kgs (132 lbs)
Actyon, 5dr SUV 06-14 CN 60 kgs (132 lbs) 60 kgs (132 lbs)
2
Fitting Kit K992
X
A B C 1 2 3
Actyon, 5dr SUV 05-13 (AU) -215mm 425mm - 980mm 935mm -
-8 -7/16ths" 16 3/4ths" - 38 9/16ths" 36 13/16ths" -
Actyon, 5dr SUV 05-13 (ZA) -215mm 425mm - 980mm 935mm -
-8 -7/16ths" 16 3/4ths" - 38 9/16ths" 36 13/16ths" -
Actyon, 5dr SUV 05-13 (EU) -215mm 425mm - 980mm 935mm -
-8 -7/16ths" 16 3/4ths" - 38 9/16ths" 36 13/16ths" -
Actyon, 5dr SUV 06-14 (CN) -215mm 425mm - 980mm 935mm -
-8 -7/16ths" 16 3/4ths" - 38 9/16ths" 36 13/16ths" -
3
Fitting Kit EN
K992
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4
Fitting Kit EN
K992
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5
Fitting Kit EN
K992
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = A835
B = A836
C = A837
D = A838
6
Fitting Kit EN
K992
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
7
Fitting Kit EN
K992
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 243
●Place rubber pads (supplied with fitting kit)
on the vehicle roof. Pad may vary in shape
to that shown.
●Make sure the pad fits into the holes
underneath the foot.
8
Fitting Kit EN
K992
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
9
Fitting Kit EN
K992
●Tighten locking screw on both legs evenly,
2.5 Nm (1.8 ft lb).
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K145 User manual
Prorack
Prorack K577W User manual
Prorack
Prorack Q19 User manual
Prorack
Prorack K395 Operation and installation manual
Prorack
Prorack K823 User manual
Prorack
Prorack K919 User manual
Prorack
Prorack K781 User manual
Prorack
Prorack K507 User manual
Prorack
Prorack K077 User manual
Prorack
Prorack K464 User manual
Prorack
Prorack K450 User manual
Prorack
Prorack PR3501 User manual
Prorack
Prorack K102 User manual
Prorack
Prorack K175 User manual
Prorack
Prorack K120 User manual
Prorack
Prorack K157 User manual
Prorack
Prorack K377 User manual
Prorack
Prorack K987 User manual
Prorack
Prorack K601 User manual
Prorack
Prorack K828 User manual
