PEERLESS WBK100-W Guide

Visit the Peerless Web Site at www.peerlessmounts.com ISSUED: 03-23-09 SHEET #:055-9262-2 10-11-12

Installation and Assembly:

WALL PLATE ACC KIT FOR PSTA-%, PSTK-%

Models: WBK100,

WBK100-W

IMPORTANT: Read instruction sheet before you start installation and assembly.

NOTE: Some parts may appear slightly different than illustrated.

1Select model of projector wall arm. Secure wall arm (sold separately) to wall plate (A) using four carriage bolts (E)

and lock nuts (D).

PSTA-028, PSTA-028-W

PSTK-028, PSTK-028-W PSTA-2955, PSTA-2955-W

PSTK-2955, PSTK-2955-W

SoldSeparately

WBK-100 WBK-100-W

Description Qt

. Part # Part #

wall plate 1 055-1923 055-2923

B#14 x 2.5 phillips hex head wood screw 4 5S1-015-C03 5S1-015-C04

Cconcrete anchor 4 590-0320 590-0320

Dlock nut 4 530-1016 530-2016

Ecarriage bolt 4 520-9207 520-2047

Parts List

Max UL Load Capacity: 50 lb (22.7 kg)

Note: The max load capacity for the

combined assembly is not to exceed the

lowest of all listed max load capacities.

Visit the Peerless Web Site at www.peerlessmounts.com ISSUED: 03-23-09 SHEET #:055-9262-2 10-11-12

2 of 3

Installation to Wood Stud Walls

Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended.

Based on its edges, draw a vertical line down the stud's center. Place wall plate (A) on wall as a template. Mark

the center of the four mounting holes. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Secure wall plate

(A) to wood stud using four #14 x 2-1/2" wood screws (B) as shown. Skip to Step 3 of universal projector wall

arm.

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is

highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs or joists.

Installers are responsible to provide hardware for other types of mounting situations.

WARNING

Visit the Peerless Web Site at www.peerlessmounts.com ISSUED: 03-23-09 SHEET #:055-9262-2 10-11-12

3 of 3

Installation to a concrete or cinder block wall

Drill four 5/16" (8 mm) dia. holes to a minimum depth

of 2.5" (64 mm). Attach wall plate (A) using four

concrete anchors (C)and four #14 x 2 -1/2" wood

screws (B) as shown in Illustration A and 1, 2, and 3.

Tighten all fasteners.

• Tighten wood screws firmly, but do not overtighten.

Overtightening can damage the screws, greatly

reducing their holding power.

• Never tighten in excess of 80 in • lb (9 N.M.).

WARNING

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual con-

crete surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a

solid part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90

specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the wall will safely support four times the combined load of the equipment and all attached

hardware and components.

Illustration A

Tighten all fasteners.

concrete

surface

UTAWAY VIEW

INCORRECT CORRECT

wall

plate

wall

plate

plaster/

drywall

plaster/

drywall

concrete concrete

Drill holes and insert anchors

Place wall plate over anchors and secure with screws

• Concrete anchors are not intended for attachment to

concrete wall covered with a layer of plaster, drywall,

or other finishing material. If mounting to concrete

wall covered with plaster/drywall is unavoidable,

plaster/drywall (up to 5/8" thick) must be

counterbored as shown right. If plaster/drywall is

thicker than 5/8", custom fasteners must be supplied

by installer. Custom fasteners were not evaluated

and tested by Underwriters Laboratories Inc.

WARNING

This manual suits for next models

Other PEERLESS Rack & Stand manuals

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 