PEERLESS SUT632P Guide

Installation and Assembly:

Peerless Ultra-Thin Tilt Mount for 22" to 40"* Flat Panel

Displays

Models: SUT632P

*Display Compatability Requirements

•Depth of display must be less than 2"

•The depth of this mount (0.68") may not provide sufﬁcient space

for proper ventilation on some displays. Please refer to the

manufacturer's requirements for mounting your display before

installation.

• The display must have a ﬂat mounting surface, or the mounting

holes need to be on the furthest back surface of the display.

• Input/Output connection must be properly oriented to accomodate

mounting 0.68" from the wall. Max UL Load Capacity: 60 lb (27.2 kg)

USC

ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com

2 of 38 ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11

NOTE: Read entire instruction sheet before you start installation and assembly.

Table of Contents

Parts List.................................................................................................................................................................................3

Installation to Wood Stud Wall................................................................................................................................................4

Installation to Solid Concrete/Cinder Block walls ...................................................................................................................5

Installing Adapter Plate...........................................................................................................................................................6

Mounting and Removing Flat Panel Display...........................................................................................................................8

Tools Needed for Assembly

•stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

•drill

• 5/16" (8mm) bit for concrete and cinder block wall

• 5/32" (4mm) bit for wood stud wall

•level

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This mount is designed to attach the display 0.68" from the wall. Please refer to manufacturer's installation guide

recommendations for required distance from wall to avoid risk of injury or property damage.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum UL Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

•Wood Beam Included

•Solid Concrete Included

•Cinder Block Included

•Metal Stud Contact Qualiﬁed Professional (not evaluated by UL)

•Brick Contact Qualiﬁed Professional (not evaluated by UL)

•Other or unsure? Contact Qualiﬁed Professional

WARNING

3 of 38 ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11

Parts may appear slightly different than illustrated.

Before you begin, make sure all parts shown are included with your product.

CEFGHI

KLM N OJ

PQ R

Description Qty. Part #

wall plate 1 046-P1058

Badapter plate 1 046-P1092

Cwood screws 2 500-1090

Dconcrete anchors 2 590-0320

EM4 x 12 mm phillips screw 6504-9013

FM4 x 25 mm phillips screw 4504-1015

GM5 x 12 mm phillips screw 4520-1027

HM5 x 25 mm phillips screw 4 520-9543

IM6 x 12 mm phillips screw 4520-1128

JM6 x 20 mm phillips screw 4 520-9402

KM6 x 25 mm phillips screw 4 520-1208

LM6 x 30 mm phillips screw 4 510-9109

MM8 x 16 mm phillips screw 6 520-9257

NM8 x 25 mm phillips screw 4 520-1031

OM8 x 40 mm phillips screw 4 520-1136

P.5" x .5" spacer 4 540-1057

Q.5 x .75" spacer 4 540-1059

Rmulti-washer 6 580-1036

S4 mm driver 1 560-1133

T4 mm allen wrench 1 560-9646

Parts List

4 of 38 ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11

Installation to Wood Stud Wall

Wall plate (A) must be mounted to a single wood stud. Use a stud ﬁnder to locate the edges of the stud. Use of an

edge-to-edge stud ﬁnder is highly recommended. Based on the stud's edges, draw a vertical line down the stud’s

center. Place wall plate on wall as a template. The top mounting slots must be located 1.48" (38mm) above the

desired display center as shown in ﬁgure 1.1. Level wall plate, and mark the center of the two mounting holes.

Make sure that the mounting holes are on the stud centerline. Drill two 5/32" (4mm) dia. holes 2" (51mm) deep.

Make sure that the wall plate is level and secure wall plate using two wood screws (C) as shown in ﬁg. 1.2.

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-

ers are responsible to provide hardware for other types of mounting situations. (not evaluated by UL)

WARNING

ﬁg. 1.2

ﬁg. 1.1

CENTER OF DISPLAY

STUD

1.48"

(38Mm)

5 of 38 ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11

Installation to Solid Concrete or Cinder Block

Make sure that wall plate (A) is level and use wall

plate as a template to mark two mounting holes. The

top mounting slots should be located 1.48" (38mm)

above the desired display center as shown in ﬁgure

1.1 on page 4. Drill two 5/16" (8mm) dia. holes to a

minimum depth of 2.5" (64mm). Insert anchors (D) in

holes ﬂush with wall as shown. Place wall plate over

anchors and secure with two wood screws (C). Level,

then tighten all fasteners.

SOLID CONCRETE CINDER BLOCK

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35mm) of actual

concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount

in a solid part of the block, generally 1" (25mm) minimum from the side of the block. Cinder block must meet ASTM

C-90 speciﬁcations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all at-

tached hardware and components.

WARNING

• Tighten screws so that wall plate is ﬁrmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Always attach concrete anchors directly to load-

bearing concrete.

• Never attach concrete anchors to concrete covered

with plaster, drywall, or other ﬁnishing material.

If mounting to concrete surfaces covered with a

ﬁnishing surface is unavoidable (not evaluated by

UL), the ﬁnishing surface must be counterbored

as shown below. Be sure concrete anchors do not

pull away from concrete when tightening screws. If

plaster/drywall is thicker than 5/8" (16mm), custom

fasteners must be supplied by installer (not evaluated

by UL).

WARNING

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate

wall

plate

plaster/

drywall

plaster/

drywall

concrete concrete

Drill holes and insert anchors (D).

Place plate (A) over anchors (D) and secure with screws (C).

Tighten all fasteners.

concrete

surface

6 of 38 ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11

Attaching Adapter Plate to Display using VESA 100 x 100

FOR VESA 100 x 100 MOUNTING PATTERN:

NOTE: Adapter plate (B) must be fully extended to access mounting holes.

Begin with the shortest length screw, hand thread through adapter adapter plate and spacer in that order into

display. Screw must make at least three full turns into the mounting hole and ﬁt snug into place. Do not over

tighten. If screw cannot make three full turns into the display, select a longer length screw. Repeat for remaining

mounting holes and tighten screws.

NOTE: For displays with a hole pattern in a pocket, spacers (P or Q) go between adapter plate (B) and display.

• Tighten screws so adapter brackets are ﬁrmly attached. Do not tighten with excessive force. Overtightening can

cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become

detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to display or product may fail.

WARNING

SCREW

DISPLAY

For displays with a hole

pattern in a pocket,

spacers (P,Q) go between

adapter plate (B) and

display.

7 of 38 ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11

Attaching Adapter Plate to Display using VESA 200 x 200 and VESA 200 x 100

• Tighten screws so adapter brackets are ﬁrmly attached. Do not tighten with excessive force. Overtightening can

cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become

detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to display or product may fail.

WARNING

Begin with longer length screw, hand thread through multi-washer, adapter plate and spacer in that order into

display. Screw must make at least three full turns into the mounting hole and ﬁt snug into place. Do not over

tighten. If screw cannot make three full turns into the display, select a shorter length screw. Repeat for remaining

mounting holes and tighten screws.

NOTE: Multi-washers and spacers may not be used depending on type of display.

NOTE: For displays with a hole pattern in a pocket, spacers (P or Q) go between adapter plate (B) and display.

For displays with a hole

pattern in a pocket,

spacers (P,Q) go between

adapter plate (B) and

display.

SCREW

MULTI-WASHER

DISPLAY DISPLAY

200 x 200 VESA PATTERN 200 x 100 VESA PATTERN

Notes:

• Multi-washers and spacers may not be

used, depending upon the type of display.

• Use the corresponding hole in the multi-

washer that matches your screw size.

LARGE HOLE FOR M6 SCREWS

SMALL HOLE FOR M4 SCREWS

MEDIUM HOLE FOR M5 SCREWS

MULTI-WASHER

8 of 38 ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11

AWALL

PLATE

FLANGES

ﬁg. 3.1

DETAIL 1

Mounting and Removing Flat Panel Display

• Always use an assistant or mechanical lifting equipment to safely lift and position the ﬂat panel displays.

• Be careful not to pinch ﬁngers when opening and closing mount from the wall.

WARNING

Fully extend tilt brackets (B) and move tilt brackets

toward wall plate (A) as shown in ﬁgure 3.1. Hook

the tilt bracket onto both sets of ﬂanges on wall

plate as shown in detail 1. Be sure ﬂanges of tilt

bracket is fully seated into wall plate ﬂanges.

Tighten safety screws using allen wrench (T) to

lock down safety latches securing adapter plate to

wall plate as shown in detail 2. Reverse step 3 to

remove display.

DETAIL 2

SAFETY

LATCH

WALL

PLATE

SAFETY

SCREW

TILT

BRACKET

FLANGES

TILT

BRACKET

FLANGES

• Tilt bracket ﬂanges must fully engage wall plate

ﬂanges as shown in detail 1 or product damage

may occur.

CAUTION

9 of 38 ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11

All other brand and product names are trademarks or registered trademarks of their respective owners.

From the collapsed position, pull from top to achieve up to 15° of forward tilt as illustrated in detail 5.

For more tilt adjustment, slightly pull out bottom and pull from top to desire tilt angle.

DETAIL 5

123

Tilt Angle Adjustment

To collapse adapter plate, grasp top and bottom of display, push bottom of display toward wall then push top of

display toward wall as illustrated in detail 3.

To extend adapter plate and access back of display, grasp top and bottom of display, pull top of display away

from wall then pull bottom of display away from wall as illustrated in detail 4.

DETAIL 3

DETAIL 4

123

Peerless Industries, Inc.

2300 White Oak Circle

Aurora, Il 60502

www.peerlessmounts.com

Instalación y ensamblaje:

Soporte inclinación Peerless Ultra-Delgado para

pantallas planas de 22" a 40"*

Modelos: SUT632P

*Requisitos para la compatibilidad de las pantallas

• La profundidad de la pantalla tiene que ser menos de 2".

• Es posible que la profundidad del soporte (0.68") no proporcione suﬁciente

espacio para la ventilación adecuada de algunas pantallas. Por favor,

repase los requisitos del fabricante en relación con la instalación de la

pantalla antes de proceder.

• La pantalla tiene que tener una superﬁcie plana para la instalación o tiene

que tener los agujeros de montaje en la superﬁcie trasera más alejada de la

pantalla.

• La conexión de entrada / salida tiene que tener la orientación adecuada

para acomodar una instalación a 0.68" de la pared. Capacidad máxima de soportar carga

por UL: 60 lb (27.2 kg)

USC

PUBLICADO: 09-10-09 HOJA #: 202-9365-4 04-05-11

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com

Table of contents

Languages:

Other PEERLESS Rack & Stand manuals

PEERLESS

PEERLESS PED 410 Guide

PEERLESS

PEERLESS PLA 50-UNL Guide

PEERLESS

PEERLESS SmartMount D-FPF-320 Guide

PEERLESS

PEERLESS Paramount PT650 Guide

PEERLESS

PEERLESS SA761P Guide

PEERLESS

PEERLESS ACC951 Guide

PEERLESS

PEERLESS ST 640 Guide

PEERLESS

PEERLESS SP730P Guide

PEERLESS

PEERLESS PARAMOUNT PRA2X2 User manual

PEERLESS

PEERLESS Smartmount Guide

PEERLESS

PEERLESS DS-VW760 and assembly Guide

PEERLESS

PEERLESS IM760P Guide

PEERLESS

PEERLESS PARAMOUNT PT640 and assembly Guide

PEERLESS

PEERLESS Solid-Point PLCM 2 Guide

PEERLESS

PEERLESS Paramount PS200 Guide

PEERLESS

PEERLESS Smartmount SA752P Guide

PEERLESS

PEERLESS SPK 811W User manual

PEERLESS

PEERLESS SUF640P and assembly Guide

PEERLESS

PEERLESS JMWS 30 Guide

PEERLESS

PEERLESS FPZ-655 Guide

PEERLESS

PEERLESS DS-VW660 and assembly Guide

PEERLESS

PEERLESS PARAMOUNT PA740 User manual

PEERLESS

PEERLESS SmartMount SF650 Guide

PEERLESS

PEERLESS CMJ 470W Guide

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 